1984 Chevrolet K5 Blazer Torque Converter and Related Products

Value-priced seal meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

Similar in performance to the Holeshot series, the Tork Master is B&M’s lowest cost torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer
• Washer Between Turbine and Cover

Torque Converter – Traveler Converter (SUV and Light Truck) for GM 1968 to 1981 TH350, TH375B APPLICATION: GM 1968 to 1981 TH350, TH375B (6) (will not fit TH-350C) Provides slightly higher stall speed than stock to improve pulling power at low speeds. New

Product Features:

• Ideal For Motor Homes
• Ideal For Towing Applications
• Precision Pump Drive Tube
• Heavy Duty Needle Bearings
• Furnace Brazed

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• New Turbine Hub
• New Springs/Rollers In Stator

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

• Fluid Balanced

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

• Designed to OE standards for ease of installation
• BWD is a global manufacturer of emission components, complete quality control is maintained through the manufacturing process from componentry to finished product

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

You can forget about the problem of shearing a torque converter bolt after you install these super strong 200,000 PSI gems. They are designed for each specific application and provide the optimum grip. Kits come with hardened parallel ground washers.

Product Features:

• Super Strong, Rated At 200,000 PSI
• Kits Come With Hardened Parallel Ground Washers
• Made In USA
• 0.590″ Underhead Length
• M10 X 1.5 Thread Size
• Set of 6