from

$54.71

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers. Mounted on side of brake pressure regulator. Fine thread pitch.

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$13.69

This wheel disc hardware kit includes rubber components used to protect the caliper pins or bolts. Worn or cracked rubber components will allow excessive movement of guide pins or bolts.

from

$1086.13

ATE is one of the world’s leading OE suppliers of brake control and brake assist systems. Hydraulic brake boosters make efficient use of the existing energy supply system in a vehicle. The hydraulic pump is used to supply, for example, power steering with the necessary high-pressure oil. It is only about the same size and weight as the tandem master cylinder. It has a substantially higher runout pressure than vacuum boosters, and is not dependent on a vacuum supply. It can therefore also be used without problem on diesel engine vehicles or on vehicles whose engines produce low vacuum levels. If the steering pump fails, the hydraulic pressure reservoir contains an adequate pressure reserve to apply the brakes several times with full boost effect. Even after this pressure reserve has been used up, it is always still possible to brake – although without reinforcement, and therefore with a significantly greater force from the foot.

Product Features:

Original equipment (OE) quality
Wide range of single and tandem Brake Boosters
Unique tie-rod design meaning lighter and thinner parts for more efficient performance

from

$48.02

ATE Original brake pads provide quality friction just like the OE pads they replace, providing customer-pleasing brake performance. With the best mixture of materials on the market and a production process which emphasizes quality all the way through, original ATE brake pads represent the state-of-the-art. In order to prevent noise during braking, highly effective primary and secondary measures are both used on brake pads. Primary measures act directly on the point of friction. Here, the main issue is optimization of the materials used for the relevant parts. In many cases, ATE uses the most effective variant and the best primary measure for noise suppression in the industry: the intermediate layer or underlayer! On the other hand, secondary measures are intended to prevent the structure-borne sound which is produced from reaching the ear of the driver and pedestrians. Secondary measures can generally be divided into four groups: damping plates, damping foils, paints and greases. ATE works with over 150 different mixtures of friction material to ensure that the optimal result is always achieved for any particular application. The friction materials are always being refined and developed for this purpose. The pad material consists of various components which each fulfill different functions during braking

Product Features:

OE engineered brake system technology assures optimum fit and performance
Advanced friction vehicle specific formulations
Reduced dusting and extend pad life
Application matched premium quality friction grade
Underlayer design helps reduce noise, vibration and harshness
Shims, chamfers, slots, wear sensors and other premium features included Original ATE Brake pads – Presentation

from

$19.93

The FAE Stop Light Switch is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium aftermarket replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$25.49

This disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this disc brake caliper bolt kit is designed to precisely tighten into stripped holes to easily repair the brake caliper or knuckle on specified vehicles
Ideal solution – this kit provides is a reliable replacement for original hardware that has stripped
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$38.82

Brake Reservoir Cap

from

$20.78

Brake Line Junction

from

$16.18

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$299.45

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

from

$16.79

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

Triggers a warning light on the dashboard
Should be replaced each time the brake pad is replaced
Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

from

$16.79

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

Triggers a warning light on the dashboard
Should be replaced each time the brake pad is replaced
Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

from

$80.96

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$282.22

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$436.24

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$25.49

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Tensile minimum load holds up to 1800 N
All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
Brand may vary by location

from

$20.73

Highest mechanical stability under load, highest compressive strength and resistance ATE/Continental has been contributing hydraulic brake hose assemblies for the automotive industry since the 1920’s. With an annual production of approximately 40 million brake hose assemblies, ATE/Continental is one of the world leaders in this sector today. As a full brake system supplier, ATE/Continental distinctively places its direct knowledge of overall hydraulic brake design into this product. The complete OEM experience, coupled with the specialized technology of an OE world market leader, uniquely places ATE/Continental near the top for brake hose assemblies with their ATE brand. ATE brake hoses are suitable for all brake fluids (DOT 3, DOT 4, DOT 4 LV, DOT 5.1)

Product Features:

More than 70 braiding machines for braid production.
Autoclaves or vulcanizing presses, and automatic surface control for the production of the inner and outer rubber layers.
Primary use of extruded connectors.
Test stands and laboratories are abundantly available for assured accuracy in satisfying the rigid criteria of all customer specifications.
Outstanding quality standards with compliance certifications for FMVSS106 on our ATE brake hose assemblies, as well as ISO 14001 certification for production.
In-house ATE N standards that exceed the legal requirements. Original ATE Brake hoses – Presentation

from

$13.98

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$9.53

Caliper housing spring retaining clips are an essential component of ATE-designed fist floating brake calipers. The fist floating caliper consists of a holder and housing, which is located in rubber damping sleeves. It slides within the holder together with the outer brake pad while as the pad wears. To prevent the housing from lifting off the pad and causing noise issues, the caliper is pulled against the brake pad by the caliper housing spring retaining clip. These clips are exposed to continuous corrosion attack and should therefore also be replaced each time the brake pads are changed.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$59.96

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$24.85

ATE Continental Teves, Inc. of Germany is one of the largest Original Equipment brake system manufacturers in the world, supplying brake components that are installed as Original Equipment by many premier vehicle automakers.

from

$20.00

ATE Continental is further extending its range of Brake Caliper Pin Boot Kits for ATE brake calipers. ATE caliper Pin Boot Kits are an essential component of ATE-designed fist floating brake calipers. The floating caliper consists of a holder and housing, which is located in rubber damping pins and sleeves.

Product Features: