1983 Ford E-250 Econoline Belts and Hoses
More 1983 Ford E-250 Econoline Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 1983 Ford E-250 Econoline, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 1983 Ford E-250 Econoline Belts and Hoses
Gates – Premium Molded Heater Hose (Part No.18020)
from
$14.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 9 Inch Length (Part No.87646)
from
$11.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Gates – Automotive XL« High Capacity V-Belt (Part No.9495)
from
$36.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – FleetRunner« Heavy-Duty V-Belt (Part No.9620HD)
from
$44.99
Designed for the toughest applications, FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at extremely prolonged operating temperatures
- Heavy-duty construction resists cracking, wear, oil and heat
- Special compound provides unmatched stability, load carrying capacity and belt life
- Unique undercord notch pattern offers increased flexibility for smaller diameter pulleys
- Problem solver for troubled drives
- Engineered to save your fleet money and reduce downtime
- Meets RMA oil and heat resistant standards and static conductivity requirements
Dorman – Fuel Filler Neck Hose (Part No.573-019)
from
$40.49
Fuel filler neck leaking? This replacement fuel filler neck hose is engineered and thoroughly tested to match the original filler neck for specific vehicle years, makes and models for a reliable repair.
Product Features:
See More
Product Features:
- Direct replacement – this fuel filler neck hose is made to match the original equipment part on specific vehicles
- Durable construction – made of fuel-resistant materials to reduce future failure potential
- Regulatory compliant – built to meet emission and inspection standards
- Trustworthy value – backed by team of engineers and quality control experts in the United States
Spectra Premium – Fuel Filler Hose (Part No.FNH012)
from
$33.49
Spectra Premium filler neck hoses are engineered, developed and validated by our in-house team of Canadian engineers ensuring it meets or exceeds the OE specifications.
Product Features:
See More
Product Features:
- Manufactured with high quality rubber to ensure it maintains its dimensional characteristics even in extreme cold/hot weather variations seen in the North American market
- OE design to ensure exact fit, form and function
- Fit tested to ensure ease of installation for the application it was intended for
- Part is tested to ensure it meets the same requirements as OE specifications
- Compatible with all fuel types it’s designed for
- Includes necessary clamps for a complete installation solution
Dayco – Serpentine Idler/Tensioner Pulley; Direct Fit, 76 mm Diameter, 8 Grooves (Part No.89053)
from
$32.49
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – V-Belt Idler/Tensioner Pulley; Steel, 94mm Dia., 16.4mm Width, Grooves (Part No.89020)
from
$24.99
Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong pl
Product Features:
See More
Product Features:
- Designed for the majority of automotive vehicle applications on the road today
- High-quality materials help resist wear and improve belt life
- Features premium lubricated bearings to extend service life
- Meets or exceeds OE quality
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 18 Inch Length (Part No.87614)
from
$12.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dorman – Molded Heater Hose: Steel (Part No.626-211)
from
$113.99
This replacement HVAC heater hose assembly is engineered to match the fit and durability of the stock heater hose assembly on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.
Product Features:
See More
Product Features:
- Ideal replacement – this HVAC heater hose assembly directly replaces the original heater hose on specified vehicle years, makes and models
- Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking
- Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
- Industry-leading design – professionally engineered by the aftermarket leader in heater hose assemblies
Gates – Emission Control Duct Hose (Part No.28095)
from
$12.99
Product Features:
See More
- Aluminum polyester construction for economy
- Black fiberglass aluminum for greater strength and durability
- Completely +exible and easily bent, yet retains shape after forming
- Resists heat, cold, oil and water
- Temperature Range: -40 Deg. F to 400 Deg. F (-40 Deg. C to +204 Deg. C)
- Temperature rating: -40 Deg. F to 400 Deg. F (-40 Deg. C to +204 Deg. C).
Dorman – Help – Carburetor Pre-Heater Hose – 2 In. X 18 In. – Aluminum (Part No.96024)
from
$5.99
This HVAC control duct hose is designed to match the fit and function of the original hose on specified vehicles, and is engineered for durability and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this HVAC control duct hose is designed to match the fit and function of the original hose on specified vehicles
- Restores functionality – reliable replacement for an original hose that has failed due to heat or vibration
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 19" Long, 1.50" Diameter (Part No.E70758)
from
$27.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Straight Heater Hose: EPDM, Direct Fit, 0.625" Inside Diameter (Sold by foot) (Part No.28411)
from
$1.49
Premium hose constructed for long service life.
Product Features:
See More
Product Features:
- Good resistance to high temperatures for extended periods of time, which prolongs service life
- Meets SAE 20R3 Standard Wall Class D-2 requirements
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- CAUTION: Do not use for fuel or oil transfer applications
- CAUTION: Do not use for fuel or oil transfer applications
- PLEASE NOTE: Item is priced and sold by the foot. See store for details.
Yukon Gear – Seal Puller Tool (Part No.56063)
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 13.88" Long, 2" Diameter (Part No.C70608)
from
$17.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Vulco-Flex« II Flexible Coolant Hose (Part No.25478)
from
$18.49
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$20.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Dayco – Dayco, Acc. Belt Idler Pulley (Part No.G6020926341DAY)
from
$19.49
The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application.
- Precision bearing
- OE High quality pulley assembly
- Durable long life performance.
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 76 mm Diameter (Part No.900005A)
from
$24.99
This pulley is manufactured by Litens Automotive – inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Litens – O.E Quality Idler/Tensioner Pulley Direct Fit, Thermoplastic, 90 mm Diameter (Part No.906003A)
from
$19.99
This pulley is manufactured by Litens Automotive the original equipment part supplier and the inventor of the first automatic belt tensioner in 1979 and today the world’s largest supplier of Original Equipment (O.E.) belt tensioning and routing products. This pulley is produced for serpentine belt routing applications and as the pulley component on automatic tensioner applications. This pulley conforms to original equipment material, tolerances, and specifications. The part is made in Canada using the O.E. specified design and meets all performance and durability requirements. Heavy duty thermoplastic construction for long life and trouble-free performance. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._
Product Features:
See More
Product Features:
- Manufactured by Litens, the largest original equipment tensioner and pulley supplier in the world, to ensure proper form, fit, and performance
- Heavy Duty Glass Reinforced Polymer Pulley for optimized dimensional control and running surface durability
- Installation instructions included.
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 94 mm Diameter (Part No.900048A)
from
$28.99
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
ACDelco – Professional Molded Coolant Hose (Part No.G2000576511ACD)
from
$49.00
ACDelco Professional, premium aftermarket Molded Coolant Hoses are composed of specially blended materials to help resist electrochemical degradation (ECD), the leading cause of hose failure. They are specially designed, GM OE style factory-molded hoses to fit today’s smaller, tighter-fitting engine compartments. ACDelco Professional Molded Coolant Hoses are temperature rated from -40 degrees Fahrenheit to 275 degrees Fahrenheit (-40 degrees Celsius to 135 degrees Celsius) and are approved for Marine applications. Do not use for fuel or oil transfer applications. These premium aftermarket replacement molded coolant hoses are manufactured to meet or exceed your expectations for fit, form, and function.
Product Features:
See More
Product Features:
- Has a heat and ozone resistant cover to increase the life of the hose
- Comes with a protective sleeve to help duplicate GM OE designs for proper fit and function
- Made of re-engineered materials to resist vacuum collapse and also reduce the need for internal springs in many applications
- Installs without buckling, bending out of shape, or straining at the connection for easy installation
- Inside diameters ranges from 1?4 in to 1 in to fit different types of vehicles
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 14.50" Long, 2" Diameter (Part No.C71216)
from
$25.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Green Stripe« Heavy-Duty Vulco-Flex« Coolant Hose (Part No.26505)
from
$38.49
Heavy-duty flexible hose designed to replace straight or curved coolant hoses. The benefit is maximum coverage with minimum inventory. Hose inside diameter remains constant from end to end. No convolutions inside hose so tube is smooth, allowing free coolant flow. Approved for marine applications.
Product Features:
See More
Product Features:
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Built-in steel spiral wire allows for medium sized curves without kinking or collapsing
- EPDM tube and Neoprene cover for extended service life
- Polyester fabric-ply reinforcement vulcanizes into shape without unnecessary strain on connections
- Resistant to heat, oil and ozone
- Performs to SAE 20R5 Type EC Class D-2 specifications
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Caution: Do not use for fuel or oil transfer applications
- Caution: Do not use for fuel or oil transfer applications.
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 9.75" Long, 1.75" Diameter (Part No.B70311)
from
$17.49
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Popular 1983 Ford E-250 Econoline Belts and Hoses Categories
1983 Ford E-250 Econoline Belts and Hoses
You count on your 1983 Ford E-250 Econoline to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 114 Belts and Hoses ranging in price from $1.49 to $79.99, you’re sure to find everything you need for your 1983 Ford E-250 Econoline.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 9 different brands like Dayco, Dorman, and Spectra Premium. 1983 Ford E-250 Econoline Belts and Hoses start as low as $1.49!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 533 extensive product reviews on 1983 Ford E-250 Econoline Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are Automotive V-Belt with 4.3 stars and Bottom Cog V-Belt; 55 Inch Long, Exact Fit Premium Quality with 3.8 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 1983 Ford E-250 Econoline below to get started!
Top-Rated Belts and Hoses Brands For Your 1983 Ford E-250 Econoline
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1983 Ford E-250 Econoline running right for years to come. In our inventory you’ll find brands like Dayco, Dorman, Spectra Premium, and even more.
Popular Dorman – Help Belts and Hoses
You’ll find popular Dorman – Help brand products across Duct Hoses. All are waiting to get your 1983 Ford E-250 Econoline back on the road. Some of the top-rated Dorman – Help products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 1983 Ford E-250 Econoline, and some of our most reviewed Dayco parts include:
from
$26.99
(27)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 5.50" Long, .63" Diameter
Heater Hoses
FAQs for 1983 Ford E-250 Econoline Belts and Hoses
What are the most purchased Belts and Hoses for the 1983 Ford E-250 Econoline?
Out of 114 Belts and Hoses for the 1983 Ford E-250 Econoline, the most popular in our inventory are:
from
$18.79
(3)
Flex Radiator Hoses; EPDM Rubber, 18.75 Inch Long, 1.75 Inch Inner Dia.
Lower Radiator Hoses
What are the top-rated 1983 Ford E-250 Econoline Belts and Hoses?
Top-rated Belts and Hoses for your 1983 Ford E-250 Econoline based on customer reviews/ratings are:
from
$16.29
(6)
Bottom Cog V-Belt; 55 Inch Long, Exact Fit Premium Quality
“Good fit, looks good and last a long time.”
