1983 Chevrolet K5 Blazer Air Intakes

Below you will find various in-demand Chevrolet Air Intakes, components and accessories for your 1983 K5 Blazer. Advance Auto Parts has popular K5 Blazer parts like Carburetor Parts, Carburetor Kits, Air Cleaner Parts and more. You’ll also find aftermarket and OEM Air Intakes for other K5 Blazer model years including 1977, 1978, 1979, 1980, 1981, 1982, 1984, 1985, 1986 and more. Select a category of 1983 Chevrolet K5 Blazer Air Intakes below and start saving instantly.

Popular 1983 Chevrolet K5 Blazer Air Intakes Categories

Intake Manifolds

Air Cleaner Assemblies

Carburetors

Throttle Position Sensors

Intake Manifold Gasket Sets

Intake Manifold Bolt Sets

Carburetor Calibration Kits

Carburetor and Injector Seal Kits

Air Cleaner Mount Gaskets

Carburetor Choke Thermostats

Carburetor Choke Pull-Offs

Intake Manifold Expansion Plugs

Throttle Position Sensor Connectors

Carburetor and Injector Mount Gaskets

Engine Intake Manifold Installation Kit

Essential Air Intakes for 1983 Chevrolet K5 Blazers

from

$5.99

Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.

Product Features:

Manufactured from high quality materials for a long service life
Torque values listed on parts (where applicable)
Easy to install
Constructed to strict engineering quality standards

from

$1972.99

Varying manifold and carburetor combinations. Suits engines air and fuel requirements. High quality Edelbrock intake gasket set. Includes gasgacinch gasket sealer. All necessary hardware included. Resists discoloration from heat. Available in cast, polished or endurashine finish.

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Convert From Single To Dual-Quad Intake
Produces Incredible Top-End Horsepower
Edelbrock Total Power Package Maximizes Gains

from

$66.99

Product Features:

Customize Carburetor Calibration and Performance
Owners Manual has Assembly Help
Includes Metering Rod Retaining Spring
Includes Metering Rods
Includes Metering Jets
Includes Step-Up Springs

from

$17.99

These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.

Product Features:

Grade 5 socket head bolts are zinc plated for protection and appearance
Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
Washers Included

from

$87.99

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

Chrome plated
Grade 8
12-point head
AN washers with no exposed shoulder for a professional appearance

from

$446.99

The Edelbrock AVS2 Series #1906 is a satin-finished four-barrel carburetor with electric choke that is designed and calibrated for optimum street performance in engines that require an air-fuel flow of 650 CFM. The AVS2 is a perfect replacement or upgrade that features annular flow primary boosters with a new calibration for improved off-idle and cruising performance. The annular flow booster design delivers improved fuel atomization to eliminate flat spots that may be encountered as the carburetor transitions from idle to full throttle. Each annular flow booster features eight equally spaced orifices to improve fuel metering from idle to the main circuit. The improved flow metering makes this carburetor ideal for use with a wide variety of small- and big-block engines with either dual- or single-plane intake manifolds. The Edelbrock AVS2 #1906 includes both timed and full vacuum ports for ignition advance. It comes with: .101 primary and.098 secondary metering jets; .070 x .037 metering rods; orange (5″ Hg) step-up spring. Use our Carburetor Stud Kits #8008 or #8024 if needed. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, RPM Air-Gap, Performer RPM, Torker II or other brands of similar design. For a black-finished AVS2 with electric choke, order part #19063.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore

from

$428.99

The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$48.99

The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.

Product Features:

Application matched components ensure carburetor can be returned to like new condition.

from

$69.05

Carquest distributes a full line of engine management products, providing the aftermarket with premium quality and comprehensive coverage.

from

$315.99

Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
Designed to meet or exceed all OEM specifications in fit, form & function
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

from

$103.99

Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
Designed to meet or exceed all OEM specifications in fit, form & function
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

from

$4.29

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$93.99

Application matched components ensure carburetor can be returned to like new condition.

from

$24.99

Application matched components ensure carburetor can be returned to like new condition.

from

$79.99

Product Features:

Application matched component to ensure the system can be returned to like new condition.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$29.99

Product Features:

Application matched component to ensure the system can be returned to like new condition.
Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

from

$16.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$7.49

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$50.99

Product Features:

Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
#1208, #1209 and #1221 fit all Edelbrock Carburetors.
Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
Dimensions are accurate within 1/8″.

from

$46.99

Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.

Product Features:

Stamped From 18-Gauge Steel
Triple-Chrome Plated
High-Quality Finish
Great Looks
Works With All 5.125 in. Carbs
Base Knock-Outs For Use w/Crankcase Ventilation

from

$35.99

Product Features:

For Chevy 1957-86 302-327-350-400 S/B Tunnel Ram
For #7110
Includes Hardware
Multi Piece Configuration
Set of 5

from

$22.99

DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES – Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE – Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED – Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$20.99

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Product constructed to meet all design and operating characteristics as intended by the manufacturer.
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$299.99

Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i

Upgrade your 1983 Chevrolet K5 Blazer with Top-Quality Air Intakes

When it comes to maintaining or upgrading your 1983 Chevrolet K5 Blazer, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Chevrolet or enhancing its overall performance, Air Intakes are key to keeping your K5 Blazer functioning at its best. At Advance Auto Parts, we offer a wide selection of 117 Air Intakes for the 1983 Chevrolet K5 Blazer, designed to meet your needs without breaking the bank. From Carburetor Part replacements to Carburetor Kits upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Air Intakes for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Air Intakes for your 1983 Chevrolet K5 Blazer at great prices. Our Air Intakes inventory for this model ranges from just $4.29 to $1,949.99, with an average price of $672.45. Our 117 Air Intakes in stock come from 11 trusted brands, so you’re sure to find the right part for your 1983 Chevrolet K5 Blazer without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1983 Chevrolet K5 Blazer, we stock popular OEM and aftermarket Air Intakes from top names like FELPRO, Edelbrock, Holley, and more. FELPRO Air Intakes start at just $4.29 and boast an impressive 4.6 stars average rating from customers. Edelbrock and Holley also bring quality to the table, with Air Intakes available starting at $50.99, and at an average 4.4 stars rating. With 534 customer reviews and counting, our 1983 Chevrolet K5 Blazer Air Intakes have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Air Intake upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1983 Chevrolet K5 Blazer is always ready to roll. We’re committed to providing you with everything you need to keep your K5 Blazer in top shape, all in one place. Start shopping confidently below for your 1983 Chevrolet K5 Blazer!

Best-Selling Carburetor Parts for 1983 Chevrolet K5 Blazers

Enhance the driving experience in your Chevrolet with 66 quality Carburetor Part components, starting at $16.99.

show more show less

from

$457.99

The Edelbrock 1404 Performer Series 500 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$799.99

The Ultra Double Pumper Carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. Three different anodized color options (Red, Blue, or Black) allow for a personalized look while maintaining the ultra high strength and durability you get from billet. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Double Pumper Carburetors have an enhanced fuel curve for optimum performance, with many more features such as aluminum construction; anodized billet aluminum metering blocks and base plate; 4 corner idle for precise idle control; mechanical secondaries for great performance; clear fuel level sight plugs for easy, no mess fuel level adjustments; Ford automatic transmission kickdown for use on popular Ford transmissions; four vacuum ports for all necessary vacuum accessories; and for the first time on a Double Pumper, factory pre-set electric choke for easy, fast cold start-ups. The clean, polished look coupled with Red, Blue, or Black metering blocks and throttle body will certainly set your ride apart whether you are at the show or track. Dont trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60s.

Product Features:

Gold Dichromate Finish For Corrosion Resistance w/Classic Look
Optimized Street/Strip Calibration That Works Out Of The Box
Man. Choke Cable Hand Controlled For Cold Start Control
Mechanical Secondaries For Awesome Tire Turning Performance
Dual Accelerator Pumps For Add Fuel Under Initial Acceleration
Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
100% Wet Flow Tested By Holley Technicians

from

$428.99

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$16.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$394.99

The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$474.99

The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$699.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$599.99

Replace your old carburetor with original Holley performance 4160 carburetors. Budget-minded enthusiasts, like you, will be rewarded with maximum performance from your stock or mildly-modified engine. These Holley 4160 adjustable float carburetors are easier to tune than full race carburetors with temperamental secondary metering blocks and dual pumps. Plus, they’re available in your choice of universal or direct fit OE replacement versions with all emission provisions. Bolt-on installation and improved performance; no wonder when car guys think of carburetors, they think of Holley 4160 carburetors!

Product Features:

Universal Holley 4-Barrel Carburetor

from

$524.99

One of the most widely used Holley carbs of all times -the 0-80508S! Its dual feed fuel inlets assure you get all the fuel you need and its 750 CFM of airflow makes it the perfect performance upgrade carb. Its vacuum secondaries and electric choke make it super easy to use on a wide range of vehicles. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.

Product Features:

Vibratory Polished For Good Looks

from

$849.99

Classic Holley carbs have been a staple for rodders around the world for decades. They’re calibrated for use on stock to mildly modified vehicles and have that classic Holley look. Holley’s 0-8007 is calibrated and intended for small V8s or 6 cylinder engines as well as 2×4 street tunnel ram style set ups. Plus, it is Gold Dichromate coated for durability and classic Holley looks. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.

Product Features:

Gold Dichromate Finish For Corrosion Resistance w/Classic Look
Factory Preset Elec Choke For Easy Startups
For All Weights/Gearing/Trans For Smooth Open Of Secondaries
Single Feed Fuel Inlet For Easy Installation
Power Valve Blow-Out Protection
Does Not Work w/A.O.D. Transmissions
Installation/Tuning DVD Incl.

from

$671.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Manual Choke For Precise Cold Start Control
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$631.99

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.

Product Features:

Gold Dichromate Finish For Corrosion Resistance w/Classic Look
Performance Upgrade For Stock To Mildly Modified Vehicles
Universal calibration for easy bolt-on performance
Man. Choke Cable Hand Controlled For Cold Start Control
Vacuum Secondaries For Use On Wide Variety Of Vehicles
Dual feed fuel inlets for constant high volume fuel delivery
Power Valve Blow Out Protection
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$437.99

The Edelbrock 9905 Remanufactured Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 9905 Remanufactured Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

from

$480.99

Vibratory Polished Alum Good Looks/Weight Savings/Lasting Shine
Performance Upgrade For Stock To Mildly Modified Vehicles
Universal Calibration For Easy Bolt-On Performance
Man. Choke Cable Hand Controlled For Cold Start Control
Vacuum Secondaries For Use On Wide Variety Of Vehicles
Single Feed Fuel Inlet For Easy Installation

from

$519.99

The Edelbrock #1901 AV2 Series 500 cfm Carburetor is designed and calibrated for small cubic-inch single carb applications, match with an Edelbrock Performer or Performer EPS manifold or other brands of similar design. Includes both timed and full vacuum

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore

from

$458.99

The Edelbrock #1902 AV2 Series 500 cfm Carburetor is designed and calibrated for small cubic-inch single carb applications, match with an Edelbrock Performer or Performer EPS manifold or other brands of similar design. Includes both timed and full vacuum

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore

from

$599.99

Gold Dichromate Finish For Corrosion Resistance w/Classic Look
Performance Upgrade For Stock To Mildly Modified Vehicles
Universal Calibration For Easy Bolt-On Performance
Man. Choke Cable Hand Controlled For Cold Start Control
Vacuum Secondaries For Use On Wide Variety Of Vehicles
Single Feed Fuel Inlet For Easy Installation
Power Valve Blow Out Protection
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run
Compensates For All Vehicle Weights Gearing/Transmissions

from

$799.99

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

Gold Dichromate Finish For Extreme Off Road Environments
Single Feed Fuel Inlet For Ease Of Installation
Optimized Off-Road Calibration That Works Out-Of-The-Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
One Piece Off-Road Vent Tube Eliminates Fuel Spillover
Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
Limited Lifetime Warranty Defects In Material/Workmanship

from

$849.99

Gold Dichromate Finish For Corrosion Resistance w/Classic Look
Optimized Street/Strip Calibration That Works Out Of The Box
Manual Choke For Precise Cold Start Control
Mechanical Secondaries For Awesome Tire Turning Performance
4 Corner Idle Allows You To Precisely Control Your Idle System
Dual Accelerator Pumps For Add. Fuel Under Initial Acceleration
Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing

from

$699.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Features A Tumble Polished Finish Can Also Be Hand Polished
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Glass Fuel Level Sight Windows For Easy Safe Float Adjustments
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
4 Corner Idle Allows You To Precisely Control Your Idle System
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians

from

$671.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Manual Choke For Precise Cold Start Control
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians

from

$538.99

Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.

from

$516.99

Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
Performance Upgrade For Stock To Mildly Modified Vehicles
Universal Calibration For Easy Bolt-On Performance
Factory Preset Electric Choke For Easy Startups
For All Weights/Gearing/Trans For Smooth Open Of Secondaries
Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
Power Valve Blow-Out Protection
Clear Fuel Level Sight Glasses
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$536.99

Vibrant Polished Alum Good Looks/Weight Savings/Lasting Shine
Performance Upgrade For Stock To Mildly Modified Vehicles
Universal Calibration For Easy Bolt-On Performance
Factory Preset Electric Choke For Easy Startups
For All Weights/Gearing/Trans For Smooth Open Of Secondaries
Single Feed Fuel Inlet For Easy Installation
Power Valve Blow-Out Protection
100% Wet Flow Tested By Holley Technicians

Top Picks for 1983 Chevrolet K5 Blazer Air Cleaner Parts

Upgrade Chevrolet K5 Blazers with top-quality Air Cleaner Parts parts, including 2 OEM and aftermarket selections for your 1983 model.

show more show less

from

$4.29

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$46.99

Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.

Product Features:

Stamped From 18-Gauge Steel
Triple-Chrome Plated
High-Quality Finish
Great Looks
Works With All 5.125 in. Carbs
Base Knock-Outs For Use w/Crankcase Ventilation

In-Demand Throttle Bodies & Carb Parts for 1983 Chevrolet K5 Blazers

Select from 2 premium Throttle Bodies & Carb Parts parts for your 1983 Chevrolet K5 Blazer, with prices ranging from $20.99 to $103.99.

show more show less

from

$20.99

Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
Product constructed to meet all design and operating characteristics as intended by the manufacturer.
OE specified wire gauge to ensure a reliable electrical connection
Designed to meet or exceed OE specifications in form, fit and function

from

$103.99

Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
Designed to meet or exceed all OEM specifications in fit, form & function
Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Most Sold 1983 Chevrolet K5 Blazer Intake Manifold Parts

Explore our best-selling Chevrolet parts for the 1983 K5 Blazer among 39 OEM and aftermarket options starting from $5.99.

show more show less

from

$395.99

Product Features:

Based on Performer Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg .Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
Fits Both Spread and Square Bore Carburetors
Also in Polished/PermaStar/EnduraShine Finish

from

$50.99

Edelbrock part #7215 Intake Gaskets for 1958-1986 E-Tec 200 Small-Block Chevy allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-2N Microp

Product Features:

1.26″x2.24″
E-Tec Port Style
.120″ Thick
Two Piece Configuration
Composite Material

from

$564.99

This is a great Manifold designed for competition engines built for circle track and drag racing using 23 degree standard port heads. Ideal for classes that require cast iron heads that require an unported intake manifold.

Product Features:

Single Plane With Isolated Plenum
Square Bore Carburetor Mounting Flange
Isolated Water Cross Over
Power Band 4500-8500 rpm
w/Maximum Velocity At Ports
Crisp Throttle Response

from

$30.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Validated for fit, form, and function
Engineered for the sealing repair environment
Unsurpassed quality you can trust

from

$34.99

Mr. Gasket Ultra-Seal Intake Manifold Gasketss are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For original equipment replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use

from

$26.99

Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Application specific design to ensure a perfect fit
Meets or exceeds all original equipment specifications
Engineered and manufactured specifically for repair applications
Unsurpassed quality you can trust
Included all parts needed to complete the repair

from

$36.99

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$17.99

Grade 5 socket head bolts are zinc plated for protection and appearance
Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
Washers Included

from

$5.99

Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.

Product Features:

Manufactured from high quality materials for a long service life
Torque values listed on parts (where applicable)
Easy to install
Constructed to strict engineering quality standards

from

$374.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Dual-plane high-rise intake. For square bore carburetors only. For street and high performance use. Available in cast, polished or endurashine finish.

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed for 1500 to 6500 RPM Street-Driven Power
Dual-Plane High-Rise Intake
For Square Bore Carburetors Only

from

$356.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used
Accepts Late-Model Choke; Waterneck; and HEI
Accepts A/C And Alternator
Accepts Exhaust Heated Chokes and Accepts EGR

from

$296.99

Product Features:

Best for the Ultimate in Street High-Performance
Designed for 1500 to 6550 RPM Street-Driven Power
Dual-Plane High-Rise Intake w/180 deg Firing Order
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock Total Power Package Maximizes Gains
Also in Polished/PermaStar/EnduraShine Finish

from

$46.99

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material.
Provides excellent sealing and durability.
Can be trimmed if necessary for modified port applications.
Complete with manifold end seals and distributor gasket.
For OE replacement, high performance street, drag race and oval track use.

from

$60.99

Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.

Product Features:

Nominally Rated At 170,000 PSI Tensile Strength
Precision Machined Threads For Secure Engagement, And Would not Rust
Wide Under Head Flange And Companion Washers Provide Even Load Distribution
Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
Facilitates Optimum Sealing Of Gasket Surfaces

from

$18.99

Replacement gasket for top to bottom. See PN(7110) complete. PN(7067) bottom. PN(7032) top. Includes base and top for intake manifold PN(7110).

Product Features:

Replacement Gasket for Top to Bottom
See PN[7110]Complete; PN[7067]Bottom; PN[7032] Top

from

$1865.99

Based on Performer RPM-Series with Unique Air Gap
Convert From Single To Dual-Quad Intake
Produces Incredible Top-End Horsepower
Edelbrock Total Power Package Maximizes Gains

from

$1332.99

For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.

Product Features:

Street Tunnel Ram; Intake Manifold Top

from

$1022.99

POWER PKG

from

$830.99

POWER PKG

from

$749.99

Polished Version Of Edelbrock PN[7501]
Polish is Hand-Buffed for Brilliant Shine
Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed for 1500 to 6500 RPM Street-Driven Power
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades

from

$746.99

Edelbrock part #71373 Pro-Flo XT intake manifold is designed for 1957-86 small-block Chevy V8 applications. The Pro-Flo XT intakes are engineered with a large plenum and long tapered runners to deliver maximum horsepower and broad torque throughout the rp

Product Features:

1500-7000 RPM Range
Single Plane Type-Throttle Body XT Style Flange
9 in. Front Height, 9 in. Center Height, 8.2 in. Rear Height
Black Powder Coated Finish
Made In The USA

from

$663.99

For 3500 to 7500 RPM
Use Where Low-End Torque is Not a Prime Factor
Great For Engines w/Slightly Modified Heads
Top Has Vacuum Outlet for Power Brakes
Will Accept Forward and Sideways Mounted Carbs
Carburetor Center-to-Center Dimensions 8.875 in
HEI Ignition Will Not Clear Manifold
For Street Mach.; Street Rods; Pro-Street; Marine

Performer EPS Manifold withOil Fill Tube for Small-Block Chevy, Polished Finish

from

$652.99

Edelbrock part No. 27031 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response. This Performer EPS intake manifold combines a modern runner design with a front mounted oil fill tube for those who want the vintage look of our Classic valve covers with no breathers. Includes Oil Fill Tube (not installed) and matching push-in breather cap. The Oil Fill Tube and Breather are also available separately as No. 4803. This intake manifold is optimized to deliver superior performance with Edelbrock square-bore Performer Series or Thunder Series AVS carburetors. This small-block Chevy manifold has a runner design that’s “tuned” for peak torque at 3500 rpm on a 350-inch engine and it’s ideal for power from off-idle to 5500 rpm. Dyno tests showed gains of 5 hp and 9 ft-lbs. of torque over the Edelbrock Performer intake manifold No. 21011 on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft-lbs. of torque for more performance where you need it most. This manifold offers a polished finish for a brilliant shine and classic look.

from

$607.99

Product Features:

Polished Version Of Edelbrock PN[7101]
Polish is Hand-Buffed for Brilliant Shine
Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed for 1500 to 6500 RPM Street-Driven Power
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades

Top-Rated Air Intakes Brands For Your 1983 Chevrolet K5 Blazer

Shop for the best-rated brands offering Air Intakes and other products for your 1983 Chevrolet K5 Blazers. Below you’ll find some of our best rated Air Intakes from FELPRO, Edelbrock, and Holley, and more. Air Intakes from these brands that fit a 1983 K5 Blazer start at just $4.29 and are rated as high as 4.6 stars. OEM and aftermarket Air Intakes don’t get more top quality, durable, and affordable than from the brands below.

Popular FELPRO 1983 Chevrolet K5 Blazer Air Intakes

When it comes to maintaining or upgrading your 1983 Chevrolet K5 Blazer, using quality Air Intakes is essential to ensure durability and a perfect fit. FELPRO ticks all of those boxes. We offer a wide selection of FELPRO Air Intakes, specifically designed for the 1983 Chevrolet K5 Blazer. With over 3 FELPRO brand Air Intakes in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $4.29, with an average price of just $17.42. Plus, with over 88 customer reviews and an average rating of 4.6 stars, you can trust that our FELPRO Air Intakes will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $4.29

(39)

Air Cleaner Mounting Gasket

“Fits great”

from $30.99

(46)

Engine Intake Manifold Gasket Set

“New intake gasket for my 25th Anniversary Corvette”

from $16.99

(3)

Carburetor Mounting Gasket

“Didn’t realize when I ordered that this was a real thick gasket, like 1/4 of some kind of crushable material. Not regular paper gasket. It works, can'”

Popular Edelbrock 1983 Chevrolet K5 Blazer Air Intakes

Edelbrock auto parts is one of the highest quality Air Intake brands in the market. Any 1983 Chevrolet K5 Blazer owner should feel confident when installing genuine Edelbrock parts in their vehicle. To ensure the best fit and performance for your 1983 K5 Blazer, Advance Auto Parts carries a full inventory of 3 Edelbrock Air Intakes. Plus you will be keeping your Chevrolet in peak condition while saving money because prices on these Edelbrock Air Intakes range from $50.99 to $457.99, plus, with more than 4 customer reviews and an impressive 4.4 stars average rating, you can be confident the Fram Air Intakes below will deliver on both quality and value.

from $50.99

(1)

Intake Manifold Gasket for 1958-1986 E-Tec 200 Small-Block Chevy

“Buy American”

from $457.99

(2)

Performer 1404 Carburetor: 500 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

“Easy install with matching Edelbrock 1107 intake manifold. Clear instructions with DVD. I had to flip my carb 180 degs so as to interface with my flat”

from $395.99

(1)

Performer Air-Gap Intake Manifold for 1955-86 Small-Block Chevy

“The casting was beautiful in its natural finish. It had a bright appearance and the surface roughness was good for a sand casting. The machine finish ”

FAQs for 1983 Chevrolet K5 Blazer Air Intakes

Which Air Intakes are best-sellers for 1983 Chevrolet K5 Blazers?

Out of 117 Air Intakes that fit 1983 Chevrolet K5 Blazers, the following parts are the top sellers:

Ultra-Seal Intake Manifold Gasket with Silicone Beading (5020476) – $34.99
Intake Manifold Bolts (6120970) – $17.99
Carburetor Mounting Gasket (5187168) – $16.99

What’s the price range for 1983 Chevrolet K5 Blazer Air Intakes?

Air Intake prices for the 1983 Chevrolet K5 Blazer start at $4.29 and go up to $1,949.99 for the most premium parts.

What’s the average price of a Air Intake for a 1983 Chevrolet K5 Blazer?

The average price for Air Intakes for the 1983 Chevrolet K5 Blazer is $672.45. Keep in mind the variety of part types within our Air Intake category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Air Intakes for other Chevrolet K5 Blazer model years?

Yes, we currently carry Air Intakes for 10 model years of Chevrolet K5 Blazers between 1975 and 1986. Air Intakes are bought most frequently for the following model years: 1986, 1985, 1984, 1982, 1981, 1980, 1979, 1978, and 1977.

What are the cheapest Air Intakes for my 1983 Chevrolet K5 Blazer?

The cheapest 1983 Chevrolet K5 Blazer Air Intakes we carry in stock are:

Air Cleaner Mounting Gasket (5785448) – $4.29
Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (22140133) – $5.99
Carburetor Mounting Gasket (5187168) – $16.99
Intake Manifold Bolts (6120970) – $17.99
Intake Manifold replacement base to top gasket (22341100) – $18.99

What are the top-rated Air Intakes that fit the 1983 Chevrolet K5 Blazer?

Out of 534 reviews by customers, our 1983 Chevrolet K5 Blazer Air Intakes have an average customer rating of . These are some of the highest-rated Air Intake types for the 1983 Chevrolet K5 Blazer and their top-rated products:

Air Cleaner Parts
- Air Cleaner Mounting Gasket (5785448) – $4.29
- Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (17140002) – $46.99
Intake Manifold Parts
- Air Cleaner Mounting Gasket (5785448) – $4.29
- Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (17140002) – $46.99

What types of Air Intakes do you sell for my 1983 Chevrolet K5 Blazer?

As of 11/2/25, these are some of the most in-demand types of Air Intakes for a 1983 Chevrolet K5 Blazer:

Can I get help with 1983 Chevrolet K5 Blazer Air Intake orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Chevrolet Air Intakes and more.

What is your return policy for Chevrolet K5 Blazer Air Intakes?

Advance Auto Parts keeps returns simple. For new Chevrolet K5 Blazer Air Intakes and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1983 Chevrolet K5 Blazer Air Intakes

Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)

Edelbrock – RPM Dual-Quad manifold and carb Kit for Big-Block Chevy Oval-Port (Part No.2065)

Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)

Mr. Gasket – Intake Manifold Bolts (Part No.955G)

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Edelbrock – AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1906)

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Wells Vehicle Electronics – Carburetor Choke Thermostat (Part No.2C1098)

Carquest – Carburetor Choke Thermostat (Part No.779-1485)

Carquest Premium – Throttle Sensor (Part No.ECC1767)

Carquest Premium – Throttle Position Sensor (Part No.ECC1245)

Felpro – Air Cleaner Mounting Gasket (Part No.60038)

Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1142)

Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1065)

Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1852)

Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1740)

Felpro – Carburetor Mounting Gasket (Part No.60482)

Felpro – Carburetor Mounting Gasket (Part No.60249)

Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)

Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)

Edelbrock – Intake Manifold replacement runner to base gaskets (Part No.6950)

Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 90314-3)

Carquest Premium – Multi-Use Connector (Part No.PTA1166)

Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)

Edelbrock – Performer 1404 Carburetor: 500 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1404)

Holley – Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet (Part No.0-4776C)

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Felpro – Carburetor Mounting Gasket (Part No.60482)

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)

Holley – Prem Street Carbs (Avengers) (Part No.0-80770)

Holley – Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate (Part No.0-9776)

Holley – Street Carbs (Part No.0-80508S)

Holley – Street Carbs (Part No.0-8007)

Holley – Prem Street Carbs (Avengers) (Part No.0-81570)

Holley – Street Carbs (Part No.0-3310C)

Edelbrock – Performer Remanufactured Carburetor, 600 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9905)

Holley – Street Carbs (Part No.0-1850S)

Edelbrock – AVS2 1901 Carburetor: 500 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1901)

Edelbrock – AVS2 1902 Carburetor: 500 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1902)

Holley – Street Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate (Part No.0-1850C)

Holley – Off Road Carbs (Part No.0-90670)

Holley – Street/Strip Carbs (Part No.0-4779C)

Holley – Carburetor – 770 CFM Alum Street Avenger E/C (Part No.0-83770)

Holley – Prem Street Carbs (Avengers) (Part No.0-81670)

United Carb – Remanufactured Carburetor 4 Barrel (Part No.3-3798)

Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80458SA)

Holley – Street Carburetor: 750 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80459SA)

Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)

Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1740)

Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1746)

Felpro – Air Cleaner Mounting Gasket (Part No.60038)

Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)

Carquest Premium – Multi-Use Connector (Part No.PTA1166)

Carquest Premium – Throttle Position Sensor (Part No.ECC1245)

Edelbrock – Performer Air-Gap Intake Manifold for 1955-86 Small-Block Chevy (Part No.2601)

Edelbrock – Intake Manifold Gasket for 1958-1986 E-Tec 200 Small-Block Chevy (Part No.7215)

Holley – Keith Dorton Series; Intake Manifold (Part No.300-110)

Felpro – Engine Intake Manifold Gasket Set (Part No.MS 90314-2)

Mr. Gasket – Ultra-Seal Intake Manifold Gasket with Silicone Beading (Part No.5821)

Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 91585)

Mr. Gasket – Intake Manifold Bolts (Part No.6091)

Mr. Gasket – Intake Manifold Bolts (Part No.955G)

Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)

Edelbrock – Performer RPM Small Block Chevy AIR-Gap Intake Manifold (Part No.7501)

Edelbrock – Performer Small-Block Chevy Intake Manifold for Street Performance (Part No.3701)

Edelbrock – Performer RPM Small Block Chevy Intake Manifold (Part No.7101)

Mr. Gasket – Intake Gasket (Part No.116)

ARP Auto Racing – For Use With Chevy 265/ 400 Cubic", 12 Point Head Type, Polished, With Washers (Part No.434-2101)

Edelbrock – Intake Manifold replacement base to top gasket (Part No.6999)

Edelbrock – RPM Dual-Quad manifold and carb Kit for 1957-86 Small-Block Chevy (Part No.2025)

Edelbrock – Small Block Chevy Street Tunnel Ram Polished (Part No.71101)

Edelbrock – POWER PKG (Part No.2020)

Edelbrock – POWER PKG (Part No.2021)

Edelbrock – Performer RPM AIR-Gap Small Block Chevy Polished Intake Manifold (Part No.75011)

Edelbrock – Pro-Flo XT Small Block Chevy EFI Black Intake Manifold (Part No.71373)

Edelbrock – Street Tunnel Ram Small Block Chevy Intake Manifold (Part No.7110)

Edelbrock – Performer EPS Manifold withOil Fill Tube for Small-Block Chevy, Polished Finish (Part No.27031)

Edelbrock – Performer RPM Small Block Chevy Polished Intake Manifold (Part No.71011)