1983 Chevrolet K10 Differentials

Essential 1983 Chevrolet K10 Differentials

Yukon Gear – 14 Plate Carbon Clutches For GM 8.2", GM 8.5", 12T, 12P, Ford 8.8" & Cast Iron ‘Vette (Part No.16041)

14 Plate Carbon Clutches For GM 8.2", GM 8.5", 12T, 12P, Ford 8.8" & Cast Iron 'Vette

from

$404.99
Product Features:
  • Clutch kit
  • Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
  • 14 piece kit
  • Carbon fiber clutches
See More

Yukon Gear – Dana 44 Pinion Gear Thrust Washer (Part No.33281)

Dana 44 Pinion Gear Thrust Washer

from

$4.99
Dana 44, GM55P & 8.2″ GM pinion gear Thrust washer.

Product Features:
  • Pinion gear thrust washer for Dana Spicer 44, GM 8.2″ and 1955-1964 GM passenger car
See More

Yukon Gear – Minor Install Kit For Dana 44 Differential (Part No.12017)

Minor Install Kit For Dana 44 Differential

from

$142.99
Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:
  • Fits standard rotation Dana Spicer 44 front
  • Included are a pinion seal, axle seals, complete shim kit, marking compound and brush.
See More

Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)

Dana 60, Dana 70 & Dana 80 Cover Bolt

from

$5.99
3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:
  • Cover bolt for Dana Spicer 60, 70 and 80
  • 3/8″
See More

Yukon Gear – Pinion Install Kit For GM 55P And 55T Differential (Part No.13060)

Pinion Install Kit For GM 55P And 55T Differential

from

$276.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:
  • Fits 1955-1964 GM truck and passenger car
  • Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
See More

Yukon Gear – Super Carrier Shim Kit For Ford 7.5", GM 7.5", 8.2" & 8.5" (Part No.55001)

Super Carrier Shim Kit For Ford 7.5", GM 7.5", 8.2" & 8.5"

from

$59.99
Product Features:
  • Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
  • Interlocking design makes installation much easier
See More

Yukon Gear – Crush Sleeve For GM 7.6" IRS, 8.5", 8.6", 8.75", 8.875" & Nissan Titan Rear – Approx 0.620" Long (Part No.33097)

Crush Sleeve For GM 7.6" IRS, 8.5", 8.6", 8.75", 8.875" & Nissan Titan Rear - Approx 0.620" Long

from

$5.99
Replacement Crush Sleeve for GM 7.6″ IRS, 8.5″, 8.6″, 8.75″, 8.875″ & Nissan Titan rear. Approx 0.620″ long.

Product Features:
  • Crush sleeve for Jeep JK rear, GM 7.6″ IRS, 8.5″ and 8.6″ and Nissan Titan rear
  • 0.620″ tall
See More

Driveworks – Tapered Roller Bearing (Part No.S-M-802048)

Tapered Roller Bearing

from

$16.99
Product Features:
  • Brand may vary by location
See More

Yukon Gear – Dana 30 / 44 Roll Pin Replacement (Part No.33312)

Dana 30 / 44 Roll Pin Replacement

from

$12.99
Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:
  • Roll pin for Dana Spicer 30 and Dana Spicer 44
  • 0.235″ diameter
See More

Richmond Gear – Differential Mini Spool (Part No.78-1028-1)

Differential Mini Spool

from

$124.99
Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:
  • For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
  • The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
  • Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
  • Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
  • Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.
See More

Richmond Gear – RngPnnInstlKt (Part No.83-1018-B)

RngPnnInstlKt

from

$39.49
RngPnnInstlKt

Yukon Gear – High Performance Replacement Ring & Pinion Gear Set For Dana 60 In A 5.13 Ratio, Thick (Part No.24607)

High Performance Replacement Ring & Pinion Gear Set For Dana 60 In A 5.13 Ratio, Thick

from

$429.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:
  • Fits standard rotation Dana Spicer 60
  • 9.75″ ring gear diameter
  • 29 spline pinion
  • 12 ring gear bolts
  • 5.13 ratio
  • Thick gear for 4.11 and down carrier
See More

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

Redline Synthetic "Shock Proof" Oil With Positraction Additive - 4 Quarts

from

$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:
  • Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
See More

Yukon Gear – Zip Locker For Dana 60 With 30 Spline Axles, 4.56 & Up (Part No.34023)

Zip Locker For Dana 60 With 30 Spline Axles, 4.56 & Up

from

$1487.99
The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:
  • Fits Dana Spicer 60 with 30 spline axles
  • 4.56 and up ratio only
  • Forged case and 8620 internals for added strength
  • Works with a variety of air delivery systems
  • Assembled in the USA
See More

Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)

Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18

from

$4.99
Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:
  • Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
  • 1/2″ x 18 thread
See More

Yukon Gear – Bearing Race Driver (Part No.56014)

Bearing Race Driver

from

$215.99
Bearing race driver. No return.

Product Features:
  • Bearing race driver
  • Fits HM88510 race
  • All steel construction
See More

Yukon Gear – Replacement Chrome Cover For Dana 44 (Part No.32004)

Replacement Chrome Cover For Dana 44

from

$67.99
0.080″ thick Chrome replacement cover for Dana 44.

Product Features:
  • Fits standard rotation Dana Spicer 44
  • Chrome
See More

National – Bearings (Part No.LM603014)

Bearings

from

$19.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Yukon Gear – Standard Open Side Gear And Thrust Washer For GM 12 Bolt Car And Truck (Part No.33380)

Standard Open Side Gear And Thrust Washer For GM 12 Bolt Car And Truck

from

$7.99
Standard Open side gear thrust washer for 12P and 12T GM.

Product Features:
  • Side gear thust washer for GM 12 bolt passenger car and truck
  • Fits standard open differentials only
See More

Yukon Gear – 3/8" Ring Gear Bolt Washer For GM 12 Bolt Car & Truck, 8.2 Bop & More (Part No.33347)

3/8" Ring Gear Bolt Washer For GM 12 Bolt Car & Truck, 8.2 Bop & More

from

$4.99
3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:
  • Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac
See More

Victor Reinz – Differential Cover Gasket (Part No.71-14868-00)

Differential Cover Gasket

from

$8.79
With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:
  • Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
See More

Yukon Gear – Standard Open Carrier Case, GM 8.5", 2.73 & Up (Part No.20083)

Standard Open Carrier Case, GM 8.5", 2.73 & Up

from

$239.99
8.5″ GM standard Open case, 2.73 & up, 28 or 30 spline.

Product Features:
  • Standard open carrier case
  • Fits GM 8.5″ with 28 or 30 spline axles
  • 2.73 and up ratio only
  • Does not include spider gears
See More

Pro-King – Differential Cross Shaft (Part No.742G673)

Differential Cross Shaft

from

$28.49
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:
  • All products are designed to meet or exceed OE quality, form, fit and funtion.
See More

Yukon Gear – Carrier Installation Kit For GM 8.5" Differential With HD Bearings (Part No.57009)

Carrier Installation Kit For GM 8.5" Differential With HD Bearings

from

$148.99
Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.5″ differential with HD bearings for large journal carrier. This kit contains carrier bearings, races and shims. This kit is used in 8.5″ differentials using a Yukon Dura Grip, Eaton posi, ValueTrac, True Trac, Pro-Series Auburn, Detroit Locker or standard carrier with large bearing journals.

Product Features:
  • Fits GM 8.5″ with aftermarket positraction
  • Works with Heavy Duty Bearings
  • Includes carrier bearings and races and “super” carrier shim kit
See More

Yukon Gear – 1541H Inner Axle For ’78 And Newer 8.5" GM (Part No.21122)

1541H Inner Axle For '78 And Newer 8.5" GM

from

$284.99
Yukon 1541H inner axle for ’78 and newer 8.5″ GM with a length of 35.5 inches and with 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy front axles come with a one year warranty against manufacturing defects.

Product Features:
  • 28 spline
  • 35.5″ long
  • Fits GM 8.5″ in 1979-1991 GM 1/2 ton
  • Left hand inner
  • 5-760X U-joint size
See More

Yukon Gear – Front 4340 Chrome-Moly Replacement Axle Kit For ’69-’80 GM Truck And Blazer (Part No.21414)

Front 4340 Chrome-Moly Replacement Axle Kit For '69-'80 GM Truck And Blazer

from

$1497.99
Yukon front 4340 Chrome-Moly replacement axle kit for ’69-’80 GM truck and Blazer, Dana 44 with 19/30 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. This kit comes with inner & outer axles for both left and right sides along with Yukon Superjoints. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:
  • 30 spline inner and 19 spline outer
  • Fits Dana Spicer 44 in 1969-1980 GM 1/2 ton
  • Includes inner and outer 4340 Chromoly axles and Yukon Super Joints
See More

Yukon Gear – Replacement Pinion Nut For Dana 25, 27, 30, 36, 44, 53 & GM 7.75" (Part No.33143)

Replacement Pinion Nut For Dana 25, 27, 30, 36, 44, 53 & GM 7.75"

from

$6.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:
  • Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
  • 3/4″ x 16 thread
See More

Yukon Gear – Pinion Nut For Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan Rear 1 5/16" Nut 7/8" X 14 Thread (Part No.33144)

Pinion Nut For Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan Rear 1 5/16" Nut 7/8" X 14 Thread

from

$7.99
Replacement pinion nut for Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan rear. 1 5/16″ nut, 7/8″ x 14 thread.

Product Features:
  • Pinion nut for Jeep JK rear, Dana Spicer 44HD, 60, 70, 70U, 70HD and Nissan Titan rear
  • 7/8″ x 14 thread
  • 1 5/16″ socket
See More

1983 Chevrolet K10 Differentials

Maybe you’re in the middle of a full rebuild of that 1983 Chevrolet K10. Maybe you just need a couple of Differentials. Either way, Advance Auto Parts has 279 different Differentials in our inventory ranging from $1.99 to $1,969.99. That means you can find the exact parts or products you need to keep that 1983 Chevrolet K10 running smoothly.

Differentials are only as good as their brand. We stock 14 different brands to make sure you have plenty of trusted parts to choose from for your 1983 Chevrolet K10. Valvoline, FELPRO, and Driveworks are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Differentials for your 1983 Chevrolet K10, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 2,421 reviews in this category, some of the top rated parts include Differential Shaft Lock Bolt with 4.0 stars and Differential Master Bearing Kit – Koyo with 3.8 stars.

So if you’re in the market for aftermarket Differentials to keep your 1983 Chevrolet K10 rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Differentials Brands To Make Your 1983 Chevrolet K10 Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1983 Chevrolet K10 demands trusted brand parts and products to keep it running. Many trusted brands of Differentials make up Advance Auto Parts’ inventory, and all are ready to help make your K10 the best it can be. Be sure to browse some of our top Differentials brands and parts.

Top 1983 Chevrolet K10 Differentials from Felpro

Felpro products are another trusted brand when it comes to Differentials for your 1983 Chevrolet K10. Popular Felpro parts include:
Differential Cover Gasket
from $9.99
(195)
Differential Cover Gasket
Rear Differential Cover Gaskets

FAQs for 1983 Chevrolet K10 Differentials

What are the most purchased Differentials for the 1983 Chevrolet K10?

Out of 279 Differentials for the 1983 Chevrolet K10, the most popular in our inventory are:
Tapered Cone/Cup Wheel Bearing Set
from $13.99
(14)
Tapered Cone/Cup Wheel Bearing Set
Front Differential Pinion Bearings
3 Qt - 80W90 Conventional Gear Oil With Posi Additive
from $57.99
This product is not rated
3 Qt – 80W90 Conventional Gear Oil With Posi Additive
Differential Oil
Bearings
from $23.99
(7)
Bearings
Front Differential Pinion Bearings

What are the top-rated 1983 Chevrolet K10 Differentials?

Top-rated Differentials for your 1983 Chevrolet K10 based on customer reviews/ratings are:
Differential Shaft Lock Bolt
from $5.99
(11)
Differential Shaft Lock Bolt
“great”
Differential Master Bearing Kit - Koyo
from $156.99
(5)
Differential Master Bearing Kit – Koyo
“was delivered as promised and on time”
Differential Ring and Pinion
from $241.99
(4)
Differential Ring and Pinion
“Perfect match and easy install”