1982 Jaguar XJ6 Steering and Chassis Parts
Find Your Specific 1982 Jaguar XJ6 Steering and Chassis Parts
Below you will find various in-demand Jaguar Steering and Chassis Parts, components and accessories for your 1982 XJ6. Advance Auto Parts has popular XJ6 parts like Ball Joints, Sway Bars, Tie Rods and more. You’ll also find aftermarket and OEM Steering and Chassis Parts for other XJ6 model years including
1989,
1990,
1991,
1992,
1993,
1994,
1995,
1996,
1997 and more. Select a category of 1982 Jaguar XJ6 Steering and Chassis Parts below and start saving instantly.
Popular 1982 Jaguar XJ6 Steering and Chassis Parts Categories
Essential Steering and Chassis Parts for 1982 Jaguar XJ6s
Edelmann – Factory New Power Steering Pump (Part No.6158U)
from
$334.99
Edelmann Elite power steering pumps represent a step up in quality and performance over typical aftermarket brand power steering pumps and are built to meet or exceed OE specifications for form, fit, and function. Designed and built with 100% new components and up-to-date designs provide for a better replacement part. Each pump is painstakingly engineered to not only eliminate commonly experienced failures caused by the OE design, but also incorporates the latest OE revisions and enhancements. Every pump has a unique Designated Numeric Asset identification number etched into the part, which verifies its authenticity and corresponds to an individualized test inspection report that is included with the product to confirm its level of quality.
Product Features:
See More
Product Features:
- Every component is 100% completely new, never reused
- Each part’s unique DNA number and testing report provides confidence that the quality of your purchase is a verified fact, not just a concept
- Re-engineered designs fix traditional OE flaws and prevent premature, repeated failures. This commitment to “working out the bugs” in OE design will allow you to leave the risk of remanufactured units behind
- Includes necessary hardware where applicable (o-ring, washers, etc…)
- Pre-installed pulley and reservoir for ease and time saving install
- U.S. based A.S.E. Certified Technical Support stands ready to provide you with assistance
Lares – Remanufactured Power Steering Pump (Part No.2009)
from
$112.99
Power Steering Pumps are thoroughly cleaned and exterior surfaces reconditioned for like-new look. Each component is carefully inspected and replaced if not to OE tolerances. All seals and O-rings are replaced with OE equivalent parts. Each unit is tested to insure OE performance. Painted with a high quality paint. All units are carefully packaged to insure safe arrival at your door. Remanufactured in the USA.
See More
Powercraft – Rack Pinion Seal Kit (Part No.9103)
from
$191.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Cardone – Power Steering Filter (Part No.20-0012F)
from
$47.49
CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.
Product Features:
See More
Product Features:
- In-line filter with serviceable filter element
- Patented built-in bypass that filters up to 190 micron particles
- Designed to extend the life of the steering system
- Sure-grip barb connections are included to ensure proper hose fitment
BBB Industries – Power Steering Filter (Part No.991-FLT4)
Rare Parts – Tie Rod End (Part No.RP28993)
from
$97.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Restores vehicle handling
- Restores OE alignment
- Reduces tire wear
- Improves steering response
Rare Parts – Tie Rod End (Part No.RP27395)
from
$89.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Restores vehicle handling
- Restores OE alignment
- Reduces tire wear
- Improves steering response
Carquest Premium – 3/8" I.D. Return Hose J189 (Part No.35002)
from
$46.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Driveworks – Tapered Cone/Cup Wheel Bearing Set (Part No.S-A-15)
from
$10.29
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
National – Tapered Roller Bearing Cone (Part No.HM89446)
from
$40.99
Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Whiteline – Sway Bar Link Washers (Part No.KW2)
from
$9.99
Has the thin galvanised metal washers on your OEM links flogged out? Whiteline have a specially designed, shaped and case hardened washers to suit the rigours wear and tear loads on sway bar link washers.
Product Features:
See More
Product Features:
- Protective plating on all metal components acts as a hard skin that is much tougher than conventional paint allowing this product to withstand the toughest conditions and resist corrosion for years to come.
Cardone – Remanufactured Rack and Pinion Assembly (Part No.26-1915)
from
$180.99
CARDONE Remanufactured Rack and Pinions are re-engineered, built and tested to meet or exceed O.E. fit and performance. 100 percent new, O.E.-style o-rings and seals are installed to ensure leak-free, long-lasting performance. A final protective coating is applied and each unit is tested to guarantee a perfect fit and function.
Product Features:
See More
Product Features:
- Protective coating applied to each unit to extend the life of the unit (where applicable).
- 100 percent performance testing to ensure perfect fit, function and reliable performance.
- 100 percent hydraulic testing for proper flow, leakage and performance ensures perfect fit and function (where applicable).
- Racks are surfaced to precise specifications to prevent leaking between chambers and extend unit life.
- 100 percent new O.E.- style o-rings and lip seals ensure leak-free and long-lasting performance (where applicable).
- All new spool valve seals and rack donut seals are installed to eliminate internal leaks and ensure reliable performance (where applicable).
- Valve housings have polished micro-finish sleeves for durability (where applicable).
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.
Cardone – Remanufactured Rack and Pinion Assembly (Part No.26-6001E)
from
$421.99
CARDONE Remanufactured Rack and Pinions are re-engineered, built and tested to meet or exceed O.E. fit and performance. 100 percent new, O.E.-style O-rings and seals are installed to ensure leak-free, long-lasting performance. A final protective coating is applied and each unit is tested to guarantee a perfect fit and function.
Product Features:
See More
Product Features:
- Protective coating applied to each unit to extend the life of the unit (where applicable).
- 100 percent performance testing to ensure perfect fit, function and reliable performance.
- 100 percent hydraulic testing for proper flow, leakage and performance ensures perfect fit and function (where applicable).
- Racks are surfaced to precise specifications to prevent leaking between chambers and extend unit life.
- 100 percent new O.E.- style O-rings and lip seals ensure leak-free and long-lasting performance (where applicable).
- All new spool valve seals and rack donut seals are installed to eliminate internal leaks and ensure reliable performance (where applicable).
- Valve housings have polished micro-finish sleeves for durability (where applicable).
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.
Rare Parts – Ball Joint (Part No.RP10718)
from
$104.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Heat treated components
- Dust seal to prevent contamination
- Restores vehicle handling
- Restores OE alignment
Rare Parts – Ball Joint (Part No.RP10716)
from
$97.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Heat treated components
- Dust seal to prevent contamination
- Restores vehicle handling
- Restores OE alignment
Carquest Premium – Power Steering Pressure Hose, 16mm Fixed Male S.A.E. x 16mm Male "O" Ring (Part No.37937)
from
$76.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
Product Features:
See More
Product Features:
- Switch sockets allow re-installation of OE pressure sensors
- Zinc coated tubes protect against rust and corrosion
- Banjo end lock tabs prevent hose end from loosening
- Double lock beading with barbed tube end provides superior hose/coupling integrity
- Heat/abrasion tubing protects vital areas
- Restrictor helps absorb vibration and reduce noise
- Movable mount bracket for easy, secure installation
- Silver heat guard protects hose in high heat areas
- Original style fittings, no adapters required
Carquest Premium – Power Steering Pressure Hose Assembly, 5/16" Male Inv. Flare x 16mm Male "O" Ring (Part No.36325)
from
$103.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Rare Parts – Bellows Kit (Part No.RP28160)
from
$60.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Protects Rack & Pinion surfaces from contamination
- Hardware included
Beck/Arnley – Steering Rack Boot Kit (Part No.103-2734)
from
$31.99
Beck/Arnley parts meet foreign nameplate OE specifications for form, fit and function. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.
Product Features:
See More
Product Features:
- Matches OE form, fit and function
- One piece neoprene boot (this is not a split boot)
- Includes boot and two clamps for complete installation.
- Quality construction for durability
- Application specific for this vehicle
Carquest Premium – 3/8" ID Return Hose (sold by each) (Part No.34995)
from
$3.29
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Carquest Premium – Power Steering Return Hose Assembly, 3/8" Male Inv. Flare x 3/8" I.D. Hose (Part No.40074)
from
$46.49
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Carquest Premium – 3/8" I.D. Return Hose J189 (Part No.36196)
from
$39.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Powercraft – Pump Drive Shaft Seal Kit (Part No.8709)
from
$13.49
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Powercraft – Pump Complete Rebuild Kit (Part No.7910)
from
$29.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Powercraft – Pump Complete Rebuild Kit (Part No.8630)
from
$36.49
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Powercraft – Pump Seal Kit (Part No.8834)
from
$65.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Powercraft – Pump Seal Kit (Part No.7918)
from
$36.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Powercraft – Pump Seal Kit (Part No.8631)
from
$14.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Upgrade your 1982 Jaguar XJ6 with Top-Quality Steering and Chassis Parts
When it comes to maintaining or upgrading your 1982 Jaguar XJ6, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Jaguar or enhancing its overall performance, Steering and Chassis Parts are key to keeping your XJ6 functioning at its best. At Advance Auto Parts, we offer a wide selection of 32 Steering and Chassis Parts for the 1982 Jaguar XJ6, designed to meet your needs without breaking the bank.
From
Ball Joint
replacements to
Sway Bars
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Steering and Chassis Parts for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Steering and Chassis Parts for your 1982 Jaguar XJ6 at great prices.
Our Steering and Chassis Parts inventory for this model
ranges from just $3.29 to $334.99, with
an average price of $68.17.
Our 32 Steering and Chassis Parts in stock come from 10 trusted brands, so you’re sure to find the right part for your 1982 Jaguar XJ6 without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1982 Jaguar XJ6, we stock popular OEM and aftermarket Steering and Chassis Parts from top names
like Carquest Premium, and more.
Carquest Premium Steering and Chassis Parts
start at just $39.99 and boast an impressive 4.4 stars average rating from customers.
With 208 customer reviews and counting, our 1982 Jaguar XJ6 Steering and Chassis Parts have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Steering and Chassis Part upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1982 Jaguar XJ6 is always ready to roll. We’re committed to providing you with everything you need to keep your XJ6 in top shape, all in one place.
Start shopping confidently below for your 1982 Jaguar XJ6!
Best-Selling Ball Joints for 1982 Jaguar XJ6s
Enhance the driving experience in your Jaguar with 2 quality Ball Joint components, starting at $97.99.
Rare Parts – Ball Joint (Part No.RP10718)
from
$104.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Heat treated components
- Dust seal to prevent contamination
- Restores vehicle handling
- Restores OE alignment
Rare Parts – Ball Joint (Part No.RP10716)
from
$97.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Heat treated components
- Dust seal to prevent contamination
- Restores vehicle handling
- Restores OE alignment
Most Popular 1982 Jaguar XJ6 Sway Bars
Customize your Jaguar with 1 Sway Bars products
like Suspension Stabilizer Bar Link Sleeves, all
priced under $9.99.
Whiteline – Sway Bar Link Washers (Part No.KW2)
from
$9.99
Has the thin galvanised metal washers on your OEM links flogged out? Whiteline have a specially designed, shaped and case hardened washers to suit the rigours wear and tear loads on sway bar link washers.
Product Features:
See More
Product Features:
- Protective plating on all metal components acts as a hard skin that is much tougher than conventional paint allowing this product to withstand the toughest conditions and resist corrosion for years to come.
Top Picks for 1982 Jaguar XJ6 Tie Rods
Upgrade Jaguar XJ6s with top-quality Tie Rods parts, including 2 OEM and aftermarket selections for your 1982 model.
Rare Parts – Tie Rod End (Part No.RP28993)
from
$97.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Restores vehicle handling
- Restores OE alignment
- Reduces tire wear
- Improves steering response
Rare Parts – Tie Rod End (Part No.RP27395)
from
$89.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Restores vehicle handling
- Restores OE alignment
- Reduces tire wear
- Improves steering response
In-Demand Power Steering Parts for 1982 Jaguar XJ6s
Select from 27 premium Power Steering Parts parts for your 1982 Jaguar XJ6, with prices ranging from $3.29 to $334.99.
Powercraft – Pump Drive Shaft Seal Kit (Part No.8709)
from
$13.49
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Cardone – Power Steering Filter (Part No.20-0058F)
from
$50.99
CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.
Product Features:
See More
Product Features:
- In-line filter with serviceable filter element
- Patented built-in bypass that filters up to 190 micron particles
- Designed to extend the life of the steering system
- Sure-grip barb connections are included to ensure proper hose fitment
Cardone – Power Steering Filter (Part No.20-0012F)
from
$47.49
CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.
Product Features:
See More
Product Features:
- In-line filter with serviceable filter element
- Patented built-in bypass that filters up to 190 micron particles
- Designed to extend the life of the steering system
- Sure-grip barb connections are included to ensure proper hose fitment
Cardone – Remanufactured Power Steering Pump (Part No.20-840)
from
$92.99
CARDONE Remanufactured Power Steering Pumps are engineered to meet or exceed O.E. performance. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Every unit undergoes a hydraulic efficiency test to ensure reliable, long-lasting performance.
Product Features:
See More
Product Features:
- All critical components (campacs, spool valves, etc.) are triple-tested to ensure product reliability.
- All units are built with 100 percent new O-rings and premium-grade HNBR seals to prevent leaks. HNBR does not break down at high temperatures like conventional seal material.
- Shafts are surfaced to precise specifications to eliminate premature seal wear and extend pump life.
- Units are supplied with 100 percent tested and calibrated pressure relief valves.
- Final pump assembly is computer-tested to measure pressure, bypass, fluid flow, valve operation, steering effort and noise to ensure reliable performance.
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.
Carquest Premium – 3/8" I.D. Return Hose J189 (Part No.36196)
from
$39.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Carquest Premium – 3/8" I.D. Return Hose J189 (Part No.35002)
from
$46.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Powercraft – Pump Seal Kit (Part No.7918)
from
$36.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Cardone – New Power Steering Filter (Part No.20-0038F)
from
$32.99
CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.
Product Features:
See More
Product Features:
- In-line filter with serviceable filter element.
- Patented built-in bypass that filters up to 190 micron particles.
- Designed to extend the life of the steering system.
- Sure-grip barb connections are included to ensure proper hose fitment.
Powercraft – Pump Complete Rebuild Kit (Part No.7910)
from
$29.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Carquest Premium – 3/8" I.D. Return Hose (J189) (sold by foot) (Part No.35001)
from
$8.79
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Carquest Premium – 3/8" ID Return Hose (sold by each) (Part No.34995)
from
$3.29
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Cardone – Power Steering Filter (Part No.20-P038F)
from
$35.49
CARDONE Steering Filters are uniquely designed to protect the steering system from damaging contaminates, which impacts performance and leads to premature power steering pump failure. These compact filters are easy to install, provide magnetic filtration, can be serviced in-line and are highly recommended to extend the life of your steering system. Available in 3/8″, 1/2″, and 5/8″ sizes to cover a most vehicle applications.
Product Features:
See More
Product Features:
- In-line filter with serviceable filter element
- Patented built-in bypass that filters up to 190 micron particles
- Designed to extend the life of the steering system
- Sure-grip barb connections are included to ensure proper hose fitment
Carquest Premium – 3/8" I.D. Return Hose J189 (Part No.36197)
from
$52.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Edelmann – Elite Power Steering Filter; Fits 99% of Hydraulic Power Steering vehicles (Part No.70699)
from
$34.99
Product Features:
See More
- Interchangeable end sizes allow the filter to fit virtually any hose size and vehicle
- Small size provides an easy fit, even in cramped systems
- Dual filtration technology eliminates metal and non-metal debris, ensuring a cleaner system
- Filter can be easily serviced, extending its functional lifespan considerably
National – Tapered Roller Bearing Cone (Part No.HM89446)
from
$40.99
Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Powercraft – Rack Pinion Seal Kit (Part No.9103)
from
$191.99
Premium-quality parts for lasting repairs. Engineered to OE design and specifications.
See More
Lares – Remanufactured Power Steering Pump (Part No.2020)
from
$111.99
Power Steering Pumps are thoroughly cleaned and exterior surfaces reconditioned for like-new look. Each component is carefully inspected and replaced if not to OE tolerances. All seals and O-rings are replaced with OE equivalent parts. Each unit is tested to insure OE performance. Painted with a high quality paint. All units are carefully packaged to insure safe arrival at your door. Remanufactured in the USA.
See More
Edelmann – Factory New Power Steering Pump (Part No.6158U)
from
$334.99
Edelmann Elite power steering pumps represent a step up in quality and performance over typical aftermarket brand power steering pumps and are built to meet or exceed OE specifications for form, fit, and function. Designed and built with 100% new components and up-to-date designs provide for a better replacement part. Each pump is painstakingly engineered to not only eliminate commonly experienced failures caused by the OE design, but also incorporates the latest OE revisions and enhancements. Every pump has a unique Designated Numeric Asset identification number etched into the part, which verifies its authenticity and corresponds to an individualized test inspection report that is included with the product to confirm its level of quality.
Product Features:
See More
Product Features:
- Every component is 100% completely new, never reused
- Each part’s unique DNA number and testing report provides confidence that the quality of your purchase is a verified fact, not just a concept
- Re-engineered designs fix traditional OE flaws and prevent premature, repeated failures. This commitment to “working out the bugs” in OE design will allow you to leave the risk of remanufactured units behind
- Includes necessary hardware where applicable (o-ring, washers, etc…)
- Pre-installed pulley and reservoir for ease and time saving install
- U.S. based A.S.E. Certified Technical Support stands ready to provide you with assistance
Cardone – Remanufactured Rack and Pinion Assembly (Part No.26-913)
from
$245.99
CARDONE Remanufactured Rack and Pinions are re-engineered, built and tested to meet or exceed O.E. fit and performance. 100 percent new, O.E.-style O-rings and seals are installed to ensure leak-free, long-lasting performance. A final protective coating is applied and each unit is tested to guarantee a perfect fit and function.
Product Features:
See More
Product Features:
- Protective coating applied to each unit to extend the life of the unit (where applicable).
- 100 percent performance testing to ensure perfect fit, function and reliable performance.
- 100 percent hydraulic testing for proper flow, leakage and performance ensures perfect fit and function (where applicable).
- Racks are surfaced to precise specifications to prevent leaking between chambers and extend unit life.
- 100 percent new O.E.- style O-rings and lip seals ensure leak-free and long-lasting performance (where applicable).
- All new spool valve seals and rack donut seals are installed to eliminate internal leaks and ensure reliable performance (where applicable).
- Valve housings have polished micro-finish sleeves for durability (where applicable).
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80 percent.
Carquest Premium – Power Steering Pressure Hose Assembly, 5/16" Male Inv. Flare x 16mm Male "O" Ring (Part No.36325)
from
$103.99
Our power steering pressure and return hoses are accurately designed and constructed to match or exceed the original equipment (OE) specifications, guaranteeing a precise and long-lasting installation. With a focus on duplicating the exact routing of the OE hoses, every bend is carefully executed to follow the original hose’s trajectory to ensure a seamless fit into the allotted space. Manufactured with quality materials and incorporating essential safety features, our hoses provide excellent protection against premature failure. Each hose is engineered to withstand the intense pressure pulsations and heat typically encountered in steering systems, offering exceptional resistance to breakdown and system contamination.
See More
Rare Parts – Bellows Kit (Part No.RP28160)
from
$60.99
This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.
Product Features:
See More
Product Features:
- Protects Rack & Pinion surfaces from contamination
- Hardware included
Rare Parts – BELLOWS KIT (Part No.RP26334)
from
$34.99
BELLOWS KIT
Beck/Arnley – Steering Rack Boot Kit (Part No.103-2734)
from
$31.99
Beck/Arnley parts meet foreign nameplate OE specifications for form, fit and function. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.
Product Features:
See More
Product Features:
- Matches OE form, fit and function
- One piece neoprene boot (this is not a split boot)
- Includes boot and two clamps for complete installation.
- Quality construction for durability
- Application specific for this vehicle
BBB Industries – Power Steering Filter (Part No.991-FLT4)
Top-Rated Steering and Chassis Parts Brands For Your 1982 Jaguar XJ6
Shop for the best-rated brands offering Steering and Chassis Parts and other products for your 1982 Jaguar XJ6s. Below you’ll find some of our best rated Steering and Chassis Parts from Carquest Premium, and more. Steering and Chassis Parts from these brands that fit a 1982 XJ6 start at just $39.99 and are rated as high as 4.4 stars. OEM and aftermarket Steering and Chassis Parts don’t get more top quality, durable, and affordable than from the brands below.
Popular Carquest Premium 1982 Jaguar XJ6 Steering and Chassis Parts
When it comes to maintaining or upgrading your 1982 Jaguar XJ6, using quality Steering and Chassis Parts is essential to ensure durability and a perfect fit. Carquest Premium ticks all of those boxes. We offer a wide selection of Carquest Premium Steering and Chassis Parts, specifically designed for the 1982 Jaguar XJ6. With over 2 Carquest Premium brand Steering and Chassis Parts in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $39.99, with an average price of just $43.49. Plus, with over 18 customer reviews and an average rating of 4.4 stars, you can trust that our Carquest Premium Steering and Chassis Parts will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
FAQs for 1982 Jaguar XJ6 Steering and Chassis Parts
Which Steering and Chassis Parts are best-sellers for 1982 Jaguar XJ6s?
Out of 32 Steering and Chassis Parts that fit 1982 Jaguar XJ6s, the following parts are the top sellers:
- 3/8" I.D. Return Hose (J189) (sold by foot) (5190122) – $8.79
- 3/8" ID Return Hose (sold by each) (18070570) – $3.29
- Pump Complete Rebuild Kit (3869172) – $29.99
What’s the price range for 1982 Jaguar XJ6 Steering and Chassis Parts?
Steering and Chassis Part prices for the 1982 Jaguar XJ6 start at $3.29 and go up to $334.99 for the most premium parts.
What’s the average price of a Steering and Chassis Part for a 1982 Jaguar XJ6?
The average price for Steering and Chassis Parts for the 1982 Jaguar XJ6 is $68.17. Keep in mind the variety of part types within our Steering and Chassis Part category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Steering and Chassis Parts for other Jaguar XJ6 model years?
What are the cheapest Steering and Chassis Parts for my 1982 Jaguar XJ6?
The cheapest 1982 Jaguar XJ6 Steering and Chassis Parts we carry in stock are:
- 3/8" ID Return Hose (sold by each) (18070570) – $3.29
- Power Steering Filter (50167394) – $7.99
- 3/8" I.D. Return Hose (J189) (sold by foot) (5190122) – $8.79
- Sway Bar Link Washers (12556806) – $9.99
- Pump Drive Shaft Seal Kit (18071199) – $13.49
What types of Steering and Chassis Parts do you sell for my 1982 Jaguar XJ6?
As of 11/2/25, these are some of the most in-demand types of Steering and Chassis Parts for a 1982 Jaguar XJ6:
Can I get help with 1982 Jaguar XJ6 Steering and Chassis Part orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Jaguar Steering and Chassis Parts and more.
What is your return policy for Jaguar XJ6 Steering and Chassis Parts?
Advance Auto Parts keeps returns simple. For new Jaguar XJ6 Steering and Chassis Parts and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
