from

$27.99

Product Features:

Brand may vary by location

from

$313.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$129.99

Product Features:

Drive flange cap
Fits Dana 60
Yukon engraved

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$205.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:56 & UP

from

$319.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$89.99

Chrome replacement cover for Dana 60 and 61(not reverse rotation!).

Product Features:

Fits standard rotation Dana Spicer 60
Chrome

from

$13.99

Product Features:

Cover gasket
Fits Dana Spicer 60, 70, 70U and 70HD

from

$544.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. This kit does not include ring gear bolts.

Product Features:

Fits 1989-1997 GM 10.5″ 14 bolt truck
Included are Timken bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

from

$317.99

Yukon standard open spider gear kit for 9.5″ GM rear and ’06 and earlier GM 9.25″ IFS with 33 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits GM 9.5″ open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$289.99

Yukon replacement standard open spider gear kit for Dana 70 and 80 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

from

$7.99

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

Power Lok case bolt for Dana Spicer 60 and 70
7/16 x 14 thread
3.5″ long
9/16″ hex head

from

$54.99

Product Features:

MINI INST KIT GM 14BLT 10.5″ 4.10DN 1972-88

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$40.99

Product Features:

Side gear spacer sleeve
Fits GM 9.25″ IFS

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$27.49

Product Features:

Brand may vary by location

from

$69.99

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

Cross pin shaft
Fits Dana Spicer 70 and 80

from

$104.99

Product Features:

Carrier shims for Dana Spicer 60 and 70U

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

from

$215.99

Bearing race driver for Dana 60 front, Dana 70U rear, Chrysler 8.75″ with 42 housing, and ’88 and older GM 14T. No return.

Product Features:

Bearing race driver
Fits HM803110 race
All steel construction

from

$26.99

Replacement pinion nut for Dana 80, 1 7/8″ socket.

Product Features:

Pinion nut for Dana Spicer 80
1 7/8″ socket

from

$323.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$1119.99

Differential

from

$1145.00

Differential

from

$446.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and silicone.

from

$13.99

14T cover gasket.

Product Features:

Cover gasket
Fits GM 10.5″ 14 bolt truck

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications