1982 Ford E-250 Econoline Performance Ignition Products
More 1982 Ford E-250 Econoline Performance Ignition Products
Find your specific 1982 Ford E-250 Econoline original or aftermarket Performance Ignition Products below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1982 Ford E-250 Econoline Performance Ignition Products
MSD Ignition – Crank Trigger Kit; Big Block Ford (Part No.8644)
from
$538.99
For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.
Product Features:
See More
Product Features:
- Absolutely the most accurate way to trigger the ignition
- The non-magnetic pickup cannot be false triggered.
- Powerful magnets are embedded in a billet aluminum trigger wheel.
- Incl. brackets/mounting hardware to fit a variety of engines
MSD Ignition – Crank Trigger Kit; Small Block Ford (Part No.8640)
from
$593.99
For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.
Product Features:
See More
Product Features:
- Absolutely The Most Accurate Way To Trigger The Ignition
- The non-magnetic pickup cannot be false triggered.
- Powerful magnets are embedded in a billet aluminum trigger wheel.
- Incl. brackets/mounting hardware to fit a variety of engines
MSD Ignition – Coil; Ford 4.6/5.4L 2-Valve 98-14 Single (Part No.8242)
from
$54.39
The improved spark energy and voltage of MSD’s blaster 2 coils, combined with reliability, have made them a favorite for performance enthusiasts. Whether firing a restored BOSS 429 or a Saturday night circle tracker, the blaster 2 has always gotten the job done. MSD is excited to offer blaster coils for late model Ford engines with coil-on-plug technology. The new blaster COPs are designed as a direct bolt-in replacement coil for many SOHC Modular Motors. The housing and installation are the same as the factory, but that’s where the similarity ends. Inside the MSD red housing, engineers spec’d better material to assemble the primary and secondary windings. There is also patented dual magnet technology to step up the output. Together, this combines a coil that produces higher voltage and spark energy. The coil-on-plug design of the blaster COPs puts the spark energy right out of the coil and across the plug gap to improve the combustion and output of the engine. The blaster 2 COPs are available individually or as a complete set of eight.
Product Features:
See More
Product Features:
- Fits 1999-2004 4.6L And 5.4L SOHC 2V
- Improved Spark Energy And Voltage Output
- Patented Winding Design and Materials
- Direct Bolt-In to Factory Connectors
- CARB approved legal for use in all states
Accel – Supercoil (Part No.140001)
from
$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
Accel – Ford 1984-98 Eec-Iv Supercoil (Part No.140012)
from
$77.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.
Product Features:
See More
Product Features:
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Standard Motor Products SMP Fd-478
- MSD 5527
- Standard Motor Products SMP Fd-478
- MSD 5527
- Resists Shock And Vibration
- Resists Corrosion
Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)
from
$42.49
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary
Product Features:
See More
Product Features:
- 42000 Volts
- Effective To 6500 RPM
- Quicker Starting
- Improved Throttle Response
- Higher RPM Power
- Can Finished In Yellow
MSD Ignition – Coil; Street Fire; Ford TFI (Part No.5527)
from
$65.99
These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.
Product Features:
See More
Product Features:
- Bolt-on Performance
- Factory replacement coil
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Popular 1982 Ford E-250 Econoline Performance Ignition Products Categories
1982 Ford E-250 Econoline Performance Ignition Products
Maybe you’re in the middle of a full rebuild of that 1982 Ford E-250 Econoline. Maybe you just need a couple of Performance Ignition Products. Either way, Advance Auto Parts has 7 different Performance Ignition Products in our inventory ranging from $30.49 to $593.99. That means you can find the exact parts or products you need to keep that 1982 Ford E-250 Econoline running smoothly.
Performance Ignition Products are only as good as their brand. We stock 3 different brands to make sure you have plenty of trusted parts to choose from for your 1982 Ford E-250 Econoline. Accel, Mallory, and MSD Ignition are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Performance Ignition Products for your 1982 Ford E-250 Econoline, but don’t take our word for it – read our customer ratings and reviews and buy with confidence.
So if you’re in the market for aftermarket Performance Ignition Products to keep your 1982 Ford E-250 Econoline rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Performance Ignition Products Brands To Make Your 1982 Ford E-250 Econoline Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1982 Ford E-250 Econoline demands trusted brand parts and products to keep it running. Many trusted brands of Performance Ignition Products make up Advance Auto Parts’ inventory, and all are ready to help make your E-250 Econoline the best it can be. Be sure to browse some of our top Performance Ignition Products brands and parts.
Popular Mallory Performance Ignition Products
We carry Mallory parts in our stock across Performance Ignition Parts categories, plus more. For a 1982 Ford E-250 Econoline, our most popular Mallory Performance Ignition Products include:
Top 1982 Ford E-250 Econoline Performance Ignition Products from Accel
Accel products are another trusted brand when it comes to Performance Ignition Products for your 1982 Ford E-250 Econoline. Popular Accel parts include:
from
$42.49
(54)
Super Stock Replacement Coil for Improved Performance, Starting, and Power
Performance Coils
FAQs for 1982 Ford E-250 Econoline Performance Ignition Products
What are the most purchased Performance Ignition Products for the 1982 Ford E-250 Econoline?
Out of 7 Performance Ignition Products for the 1982 Ford E-250 Econoline, the most popular in our inventory are:
