1982 Ford C800 Starter Parts

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Carquest Starters take advantage of the power of 100% NEW to restore hard working vehicles to OE specified performance & endurance. All new units and components offer unmatched performance, reduce downtime & customer comebacks. Carquest Starters are primed to keep fleets moving forward. Built to perform in severe duty environments, with high output capabilities built in through improved technical & material formulas for high power output and efficient performance.

Product Features:

• High quality components form the foundation our parts are built from. Transpo¿s innovative and high quality electronic technologies for internal components are incorporated to achieve high performance outputs.
• Power & Efficiency are designed into every component. No matter the ambient temperature, starters will provide maximum cranking power to get engines running.
• Connectors and power transmission components are highly resistant to extreme moisture environments because we use nickel plated contactors and double armature coating. We maintain a rigorous test schedule with endurance, salt spray, dirt and grime and out
• Integrated magnetic switch provides protection against weak power from batteries.
• Over-Crank Protection (OCP) Monitors heat in starter from over cranking & shuts down starter to prevent burning
• Precision design and machining are the Extreme vibration failure solution. Vehicles often perform in adverse conditions like extreme temperatures that create tolerance shifts that produce high frequency vibration, which leads to resistance in power transf

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The Starter Solenoid is the relay of the starting circuit that carries the high amperage required when the starter motor is engaged. The solenoid is typically energized by the starter switch when commanded by the vehicle operator. Starter solenoids may also be used in other high amperage circuits, compare solenoid specification to your circuit needs before installing.

Product Features:

• Application matched component to ensure the system can be returned to like new condition.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.