1982 Chevrolet G10 Performance Engines

Essential 1982 Chevrolet G10 Performance Engines

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Intake Bolt Kit

from

$75.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:
  • Chrome plated
  • Grade 8
  • 12-point head
  • AN washers with no exposed shoulder for a professional appearance
See More

Edelbrock – RPM Small-Block Chevy Cylinder Head SBC 70cc Flat Tappet Cam Polished (Part No.607519)

RPM Small-Block Chevy Cylinder Head SBC 70cc Flat Tappet Cam Polished

from

$958.99
The Edelbrock #607519 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

Product Features:
  • Complete Single For Hydraulic Flat Tappet
  • 70cc Combustion Chamber Volume
  • 185cc Intake/65cc Exhaust Runner Volume
  • 2.02 in. Intake/1.6 in. Exhaust Valve Diameter
  • 0.562 in. Deck Thickness
See More

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Engine Timing Cover Gasket

from

$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Steel core gasket construction
  • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Competition Cams – CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA (Part No.12-602-4)

CAMSHAFT, SBC 295 BIG MUTHA THUMPR HYDRAULIC 1 EA

from

$529.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Pushrod Set for S/B Chevy

from

$187.99


Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Edelbrock – Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish (Part No.2104)

Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish

from

$329.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 Deg Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
  • Accepts Late-Model Choke; Waterneck; and HEI
  • Accepts A/C And Alternator
  • Accepts Exhaust Heated Chokes
See More

Mr. Gasket – Ultra Seal: Sure-Lock Rocker Arm Nuts (Part No.920G)

Ultra Seal: Sure-Lock Rocker Arm Nuts

from

$64.19
These are high quality nuts with allen set screws to provide you with that positive lock needed for Race or original equipment Rocker Arms.

Product Features:
  • They Are Zinc Dichromate Plated Steel
  • They Have Black Oxide Coated Set Screws
  • Keeps Rocker Arms Positively Locked
  • (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
  • Includes Locks and Hex Wrench
  • Shank O.D. .603″
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Cylinder Head Dowel Pins

from

$14.99
Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5801G)

Ultra Seal: Head Gasket

from

$64.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.190 inch, Compressed thickness 0.038 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Mr. Gasket – Intake Gasket (Part No.143)

Intake Gasket

from

$42.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
See More

Edelbrock – Intake Manifold Gasket for 1985-1995, Chevy V6 200-229-262 (Part No.7209)

Intake Manifold Gasket for 1985-1995, Chevy V6 200-229-262

from

$27.99
Edelbrock part #7209 Intake Gaskets for 1985-1995, Chevy V6 200-229-262 (3.8 and 4.3L) allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-

Product Features:
  • 1.28″x2.10″
  • Stock Port Style
  • .060″ Thick
  • Multi Piece Configuration
  • Composite Material
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1819)

PERFORMANCE OIL PAN GASKET SET

from

$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Engine Sealing (Part No.6560)

Engine Sealing

from

$499.99
Manufactured from cellulose and nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement, high performance street, drag race and oval track.

Product Features:
  • Made of high temp silicone or nitrile blend rubber
  • Torque limiters to prevent over tightening
  • One piece molded rubber
  • Fits left and right hand dipsticks
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Performer Series Retainer (Qty 16)

from

$95.99
Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:
  • Valve Spring Retainers for Use OE Cast Iron Heads
  • Superior Quality Heat-Treated Steel
  • Machined for Strength with Black Oxide Finish
  • Finish Ensures Rust and Corrosion Protection
See More

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Performance Torque Converter for GM TH400, 350, & 375 Transmissions

from

$299.99
Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

B & M – Holeshot 2400 (Part No.20412)

Holeshot 2400

from

$499.99
HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

Weiand – Team G; Water Pump Spacer Kit (Part No.8207)

Team G; Water Pump Spacer Kit

from

$112.99
Use with a short water pump to convert to a long water pump.

Product Features:
  • Water Pump Spacer Kit
See More

Mr. Gasket – Bolt Water Pump (Part No.4998)

Bolt Water Pump

from

$32.99
This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:
  • Chrome Plated
  • Grade 5
  • AN washers with no exposed shoulder for a professional appearance
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

Engine Valve Cover Gasket Set

from

$23.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Valve Cover Gasket Set for Chevrolet (Part No.7549)

Valve Cover Gasket Set for Chevrolet

from

$35.99
Product Features:
  • Valve Cover Gasket
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$151.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

PERFORMANCE REAR MAIN SEAL SET

from

$36.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Rear Main Seal Gasket

from

$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

1982 Chevrolet G10 Performance Engines

Maybe you’re in the middle of a full rebuild of that 1982 Chevrolet G10. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 88 different Performance Engines in our inventory ranging from $14.99 to $1,268.99. That means you can find the exact parts or products you need to keep that 1982 Chevrolet G10 running smoothly.

Performance Engines are only as good as their brand. We stock 6 different brands to make sure you have plenty of trusted parts to choose from for your 1982 Chevrolet G10. Mr. Gasket, Edelbrock, and FEL-PRO Performance are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1982 Chevrolet G10, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 330 reviews in this category, some of the top rated parts include Action Plus Water Pumps with 3.7 stars and Action Plus Water Pumps with 1.5 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1982 Chevrolet G10 rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1982 Chevrolet G10 Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1982 Chevrolet G10 demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your G10 the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular B & M Performance Engines

We carry B & M parts in our stock across Performance Torque Converters categories, plus more. For a 1982 Chevrolet G10, our most popular B & M Performance Engines include:
Tork Master 2400
from $339.99
(1)
Tork Master 2400
Performance Torque Converters
Tork Master 3000
from $499.99
(1)
Tork Master 3000
Performance Torque Converters

Top 1982 Chevrolet G10 Performance Engines from Mr. Gasket

Mr. Gasket products are another trusted brand when it comes to Performance Engines for your 1982 Chevrolet G10. Popular Mr. Gasket parts include:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats

FAQs for 1982 Chevrolet G10 Performance Engines

What are the most purchased Performance Engines for the 1982 Chevrolet G10?

Out of 88 Performance Engines for the 1982 Chevrolet G10, the most popular in our inventory are:
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
from $195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
from $39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $52.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets

What are the top-rated 1982 Chevrolet G10 Performance Engines?

Top-rated Performance Engines for your 1982 Chevrolet G10 based on customer reviews/ratings are:
Action Plus Water Pumps
from $215.99
(3)
Action Plus Water Pumps
“I bought this item for my 1979 Camaro SBC for Street/Strip application. Water pump weighs 4 LBS less than factory, comes with its own cork gaskets. N”
Action Plus Water Pumps
from $215.99
(2)
Action Plus Water Pumps
“The twisted neck comes to far up on the hub. For a 2 groove pulley it causes the pulley to hit the water pump. You will also need new bolts for the”
MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST
from $213.99
(1)
MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST
“just spill on break in oil on rocker wheels,adjust nut down till u can’t go any more and then back off 1/2 turn and your done no noise on start up eve”