from

$512.99

The industry standard for over 30 years, this shifter offers state of the art transmission control for popular manual transmissions. Dedicated applications assure a custom fit to a wide variety of vehicles.

Product Features:

High Ratio Pivot Mechanism
Adjustable Bias Spring Loads
Adjustable Stops
Chrome Plated Steel Bolt On Stick
Easy Installation

from

$15.99

Designed to fit all GM HEI distributors with E clips. The kit includes two weights, special center plate, three sets of color coded springs and two pairs of nylon bushings. Also, included is a comprehensive instruction sheet, complete with graphs showing typical advance rates using various spring/weight combinations.

Product Features:

Fits 1974-79 GM HEI distributors with e-clips
Includes detailed instructions
Weights springs center plate and nylon bushings

from

$55.99

This AIRAID Direct-Fit Replacement Filter is a drop-in replacement for your vehicle’s stock paper air filter that is designed to improve horsepower and acceleration. The air filter is constructed with multiple layers of filter media and provides significant improvements in air flow and filtration compared to typical replacement filters with the added benefit of being washable and reusable. Why throw money away on a paper filter each time the old one gets dirty when you can upgrade to a serviceable AIRAID Direct-Fit Replacement Filter for often less than the cost of two stock replacements? Installation takes only minutes and is as simple as replacing your stock filter.

from

$113.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$25.99

Creates a positive seal. Controlled swelling gasket. Thickness will not decrease. Eliminates re-torque of valves. High-tensile strength. Handles ex flange pressure and forms a leak proof seal. Black latex coating.

Product Features:

Creates a positive seal by controlling swelling
Available in extra thick for rocker arm clearance

from

$243.99

Product Features:

GM 10BL 8.5 R/P 2.73 FRT/REAR MGP

from

$5.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$461.99

Matched assembly for maximum reliability. An excellent choice for high performance street applications.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability
Designed for Street And Street Strip Applications

from

$71.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$154.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$18.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$72.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$40.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$125.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$186.99

This Spectre Oil Pan was designed for 1974-1981 Pontiac 301-455 engines. This triple chrome plated oil pan has a stock capacity.

Product Features:

Triple chrome-plated
Steel construction
Stock capacity
For 1974-1981 Pontiac 301-455 engines

from

$696.99

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

2800-3200 RPM
Small And Big Blocks
Serious Performance
Furnace Brazed
Fully Balanced

from

$513.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used
Accepts Late-Model Choke; Waterneck; and HEI
Accepts A/C And Alternator
Accepts Exhaust Heated Chokes and Accepts EGR

from

$23.79

Spectre’s Pontiac water neck fits 1967 – 1978 Pontiac V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts and sealing O-ring.

Product Features:

Fits 1967 – 1978 Pontiac V8 engines
Includes sealing O-ring and bolts
Chrome plated
Easy to install

from

$25.99

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features:

Made from HYPER-Flex Polyurethane
Allows Vehicle to Work At Maximum Efficiency
Easy to Install
Superior Performance and Greater Longevity
Lasts Much Longer Than OEM Rubber End Links

from

$266.99

Quality chrome plated and remanufactured to exceed OEM specifications for maximum dependability. Tested and output rated at 60 amps.

Product Features:

Exceeds OEM specifications
Output rated to 60 amps
Remanufactured

from

$15.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for repair applications
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$766.99

Product Features:

Designed For Carbureted V8s
Power Increases From 100-250 HP
Precision EDM Machined Spray Bars
Simple To Install

from

$11.99

Energy Suspension performance bump stops help cushion a collapsing suspension, preventing bottoming-out and expensive vehicle damage. Hyper-Flex performance polyurethane bump stops for control arms, traction bars, leaf springs, etc. are guaranteed to last longer and operate more efficiently than original rubber stops. The smaller, general purpose bullet shaped snubber is ideal for control arms. the low profile button head is for use when clearance is limited. Our large competition race style bump stops smooth out compression better and have a large reinforced metal plate welded to the mounting plate and molded-in. Each style is specially designed for a perfect and custom fit and each style has it’s own durometer, hardness, characteristics. Energy’s wide selection of bump stops are available in red or black color.

Product Features:

Made of Superior Hyper-Flex+ Material
Helps Prevent Damage to Control Arm

from

$622.99

New qwik-tune adjustable secondary air valve. Optional single or dual fuel inlet. Distinctive black accented hardware. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage. Exclusive 12 month complete satisfaction warranty.

Product Features:

New Qwik-Tune Adjustable Secondary Air Valve
Optional Single Or Dual Fuel Inlet
Distinctive Black Accented Hardware
No Gaskets Below Fuel Level to Prevent Leakage
Metering Rod/Step Up Springs Can Be Changed Easily
GM/AMC-Style Throttle Linkage
Exclusive 12 Month Complete Satisfaction Warranty

from

$88.99

Designed for 1968-1981 Buick 350 V8 engines, this valve cover features chrome-plated steel construction. The valve cover is stock height and baffled to provide optimum function. Spectre engineers its valve covers to look great for applications ranging from replacing a stock valve cover to a custom build. Includes two valve covers.

Product Features:

Fits 1968-81 Buick 350 V8 engines
Two valve covers are included
Steel construction with a triple chrome-plated finish
Features OEM style and height

from

$30.99

Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:

Withstands intense exhaust heat
Graphite-impregnated facing
Steel expanded metal core
Superior tensile strength
Resists deteriorating
Anti-stick properties
Easy removal for disassembly

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$133.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features: