from

$3.99

AT SHF LINK BUSHING

from

$33.49

Fully adjustable vacuum modulator to maintain accurate shift points.

Product Features:

Meets or exceeds OE fit, form and function

from

$45.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$8.99

AT OIL PUMP ORING

from

$22.99

Detent cables connect the throttle mechanism to the transmission. Old cables can bind, break, or just become sluggish. The best repair is to replace the old cable with a new one. ATP Detent cables are designed to fit And function just like the original part to ensure durability And long life.

Product Features:

Includes brackets, grommets, etc to match original
Helps transmission determine ideal downshift
Improves vehicle performance

from

$25.99

Detent cables connect the throttle mechanism to the transmission. Old cables can bind, break, or just become sluggish. The best repair is to replace the old cable with a new one. ATP Detent cables are designed to fit and function just like the original part to ensure durability and long life.

Product Features:

Includes brackets, grommets, etc to match original
Helps transmission determine ideal downshift
Improves vehicle performance

from

$58.99

These universal fit adjustable cables will work in 95% of all listed transmission applications, yet are less expensive than OE models. Use as straight replacement cable or ease the installation of transmission swaps.

Product Features:

Universal Fit Adjustable
Less Expensive Than OE Models
Ease Trans. Swap Installation

from

$84.99

When swapping the TH400 transmission into any vehicle, this kit makes installation of the transmission’s kickdown feature a snap. This switch mounts to either a TH700R4, TH200, TH200-R4 or TH350 throttle cable bracket.

Product Features:

Allows High Speed Cruise
Cruise In Overdrive
Prevents Part Throttle Kickdown
Quick Installation

from

$109.99

This kit allows you to adjust the shift points of your transmission after it is installed in your vehicle. The Governor Recalibration Kit is very useful if you have a vehicle that is very light; has a low rear-end gear ratio.

Product Features:

Adjust Shift Points Of Transmission
Useful For Light Vehicles
For Low Rear End Gear Ratio
Or Useful If It Is Conversion

from

$18.99

Product Features:

Edelbrock Part # 8026 GM Transmission adapter is for use with 2004R, 700R4, 4L60 transmissions.
This kit relocates the pin position on an Edelbrock Carburetor when hooking up to a throttle valve style transmission (700R4, 2004R, 4L60).
The pin location is critical as the TV controls line pressure, shift points, shift firmness, and part throttle downshifts.

from

$30.99

Includes dipstick with chromed steel handle and chromed steel dipstick tube with mounting tab. 27 inch long.

Product Features:

Fits GM Th350 – Chevy Specific. Modify For Others
27 In Length
Chrome Plated Steel

from

$1995.99

(PDT)Premium Drivetrain Transmissions are remanufactured to original equipment (OEM) demanding specifications by an OEM builder. Each transmission assembly is manufactured with the highest technology equipment, the most intelligent engineering support, and the best practices available in remanufacturing today.

Product Features:

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
Product might not be available in all states due to local laws.

from

$1995.99

(PDT)Premium Drivetrain Transmissions are remanufactured to original equipment (OEM) demanding specifications by an OEM builder. Each transmission assembly is manufactured with the highest technology equipment, the most intelligent engineering support, and the best practices available in remanufacturing today.

Product Features:

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
Product might not be available in all states due to local laws.

from

$2353.00

Our remanufactured transmissions have improved torque converters included with every transmission to eliminate the possibility of front seal leaks, vibration or premature bushing wear, All torque converters are tested for leaks, lock-up, concentricity & balance. Every fully remanufactured valve body, with complete system correction & recalibration kit, is tested independently & includes updated throttle valve, manual valve, 4-spool switch valve, pressure regulator valve & governor plugs for improved shifting, lubrication & performance. All wear-prone valves are restored to stringent specifications & vacuum tested to confirm proper function. Each remanufactured transmission is hot, cold, load & simulated road testing. All remanufactured transmissions are backed by the industry’s best, no-hassle nationwide warranty.

Product Features:

Our Remanufactured Transmissions include torque convertors, trans is completely disassembled & checked then reassembled to spec for tolerances, vacuum, seal & balance, all wear parts replaced & sim tested.
If we have important installation information it will be included on tags or in the paperwork packaged with your transmission.
Transmissions are securely packaged in a recyclable container that will also protect your core on the return trip. Our nationwide warehouse network means speedy delivery.
All of our transmissions are Dyno tested to ensure the highest standard of trouble free service and longevity.

from

$1995.99

(PDT)Premium Drivetrain Transmissions are remanufactured to original equipment (OEM) demanding specifications by an OEM builder. Each transmission assembly is manufactured with the highest technology equipment, the most intelligent engineering support, and the best practices available in remanufacturing today.

Product Features:

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
Product might not be available in all states due to local laws.

from

$3.99

AT SOLENOID SEAL

from

$7.99

This brake pedal bushing is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this brake pedal bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$8.29

This clutch pilot bushing is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this clutch pilot bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$7.99

This clutch pilot bushing is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this clutch pilot bushing matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience