1981 Ford E-350 Econoline Differentials

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

• Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 10.25″ & 10.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Ford 10.25″ and 10.5″
• Includes carrier bearings and races and “super” carrier shim kit

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction

Product Features:

• Inner oil slinger for Dana Spicer 60

Product Features:

• Pinion depth shims for Dana Spicer 60 and 70U

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Differential Carrier

Yukon replacement standard open spider gear kit for Dana 60 with 32 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 60 open differential with 32 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Replacement pinion seal for 1998 and newer Ford (flanged style) Dana 80.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Dana Spicer 80 with 4.375″ O.D. pinion bearing

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

This kit uses Koyo bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. USA Standard Gear does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Dana Spicer 70HD
• Fits Dana Spicer Super 70
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion nut, marking compound and brush.

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• Carrier shim kit
• Fits Dana Spicer 70 and 70HD

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 35 spline axles
• 4.10 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 60 rear
• Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

Seal housing for Ford 10.25″ & 10.5″, Zip locker, with o-rings.

Product Features:

• Seal housing for Ford 10.25″ and 10.5″
• Includes o-rings

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 60

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Dana Spicer 60 with 30 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Differential

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Replacement pinion nut for Dana 80, 1 7/8″ socket.

Product Features:

• Pinion nut for Dana Spicer 80
• 1 7/8″ socket

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Product Features:

• Bulkhead fitting

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This gear set is designed for 1993 and newer trucks. When installing this gear set in a 99-’06 10.5″ housing you will need a PK F10.25 or YK F10.25 kit. If installing into a ’07-’10 10.5″ housing, use a PK F10.5-B or YK F10.5-B kit. If installing into a ’92 & down housing a new yoke will be needed.

Product Features:

• Fits 1993 – 1999 Ford 10.25″
• 10.25″ ring gear diameter
• 31 spline pinion
• Long pinion
• 12 ring gear bolts
• 4.11 ratio

Product Features:

• Fits Dana Spicer 80
• Finned aluminum

This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

Dana 70 & Dana 80 standard Open cross pin shaft, one piece case.

Product Features:

• Cross pin shaft
• Fits Dana Spicer 70 and 80