1981 Ford E-250 Econoline Differentials

Yukon Trac Loc internals for 8″ & 9″ Ford, 31 spline, includes hub & clutches. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Ford 9″ with Trac Loc positraction with 31 spline axles
• Includes two side gears, four pinion gears, cross pin shaft, clutch hub, roll pin and spider gear thrust washers.

Product Features:

• Standard open carrier case and spiders
• Fits Ford 8.8″ with 31 spline axles

Axle shaft damaged or bearings worn out. This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

Product Features:

• Brand may vary by location

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

• Pilot bearing
• Fits Ford 9″
• 0.656″ thick

Standard open or TracLoc cross pin shafts and block in four pinion design for 9″ Ford.

Product Features:

• Cross pin shaft and block kit
• Fits Ford 9″
• Includes cross pin block and three cross pin shafts

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

2 piece solid spacer for Ford 8.8 and 7.5.

Product Features:

• Crush sleeve eliminator kit for Ford 7.5″ and 8.8″

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 10.25″ & 10.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Ford 10.25″ and 10.5″
• Includes carrier bearings and races and “super” carrier shim kit

Yukon standard open spider gear kit for 9.75″ Ford with 34 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 9.75″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Pinion depth shim kit 9″ Ford.

Product Features:

• Pinion depth shims for Ford 9″

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Yukon Performance 2-3/16″ deck steel spool for 9″ Ford with 35 spline axles. Spool uses 2″ journal bearings (30 degree). Does not fit Mark Williams. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 35 spline axles
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Product Features:

• Trac Loc positraction
• Fits Ford 8.8″ with 31 spline axles

Pilot bearing retainer for Ford 9″.

Product Features:

• Pilot bearing retainer for Ford 9″

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Seal housing for Ford 10.25″ & 10.5″, Zip locker, with o-rings.

Product Features:

• Seal housing for Ford 10.25″ and 10.5″
• Includes o-rings

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with35 spline pinion
• For oversize applications
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

Product Features:

• Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

Product Features:

• Inner oil slinger for Dana Spicer 60

20 long air line for Zip Locker.

Product Features:

• Air line
• 20′ in length

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush and gasket.

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U

Side gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.875″ diameter cross pin shaft applications only