from

$475.88

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$16.79

The Wearever brand offers a complete line of quality products that are appealing alternatives to higher priced brands without sacrificing quality, durability or performance. Wearever Brake Pad Wear Sensors offer an OE safety feature designed to warn the driver when a brake pad is worn or at the end of its life cycle.

Product Features:

Triggers a warning light on the dashboard
Should be replaced each time the brake pad is replaced
Not available for all makes and models, refer to your vehicle’s owner Manual to validate the number of brake pad wear sensors are required, when applicable

from

$23.75

Highest mechanical stability under load, highest compressive strength and resistance ATE/Continental has been contributing hydraulic brake hose assemblies for the automotive industry since the 1920’s. With an annual production of approximately 40 million brake hose assemblies, ATE/Continental is one of the world leaders in this sector today. As a full brake system supplier, ATE/Continental distinctively places its direct knowledge of overall hydraulic brake design into this product. The complete OEM experience, coupled with the specialized technology of an OE world market leader, uniquely places ATE/Continental near the top for brake hose assemblies with their ATE brand. ATE brake hoses are suitable for all brake fluids (DOT 3, DOT 4, DOT 4 LV, DOT 5.1)

Product Features:

More than 70 braiding machines for braid production.
Autoclaves or vulcanizing presses, and automatic surface control for the production of the inner and outer rubber layers.
Primary use of extruded connectors.
Test stands and laboratories are abundantly available for assured accuracy in satisfying the rigid criteria of all customer specifications.
Outstanding quality standards with compliance certifications for FMVSS106 on our ATE brake hose assemblies, as well as ISO 14001 certification for production.
In-house ATE N standards that exceed the legal requirements. Original ATE Brake hoses – Presentation

from

$43.99

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

Application-specific friction formulations provide shorter stopping distances and extended pad life
Hardware included for most applications, provides better value and
OE-designed slots and chamfers to reduce noise and vibration
Multi-layer shim provides near silent braking
Powder-coated backing plate prevents corrosion

from

$2.30

Platform specific rubber to metal composite material designed to solve noise and vibration problems. MTC rubber to metal composite materials for noise damping in disc brakes combine a number of valuable Features and Benefits: vibration insulation, compressibility and excellent adhesion. The rubber composite materials are excellent for applications with demanding insulation for vibration and noise. The materials retain their integrity even when subjected to high pressure and high temperature. MTC brake pad shims are cut specially to suit specific vehicle models and fit perfectly with genuine pads and those made by other manufacturers.

Product Features:

Platform Specific Design
Combats Brake Squeal
OE-Style Composite Core Shim
Effective Thermal Barrier

from

$28.30

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$15.00

Wagner TQ® brake pads feature a zero-copper friction formulation and a unique Integrally Molded Insulator (IMI) technology for quieter operation.

Product Features:

QUIETER OPERATION — Application-specific design and a unique laser-shaped friction spreads out heat, sound and vibration to reduce noise opportunities
COMPREHENSIVE COVERAGE — Brake pads available for most vehicles on the road

from

$61.69

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$68.14

Since 2008 Zimmermann is offering almost 400 Standard and almost 400 Sports Brake Discs in a coated version named Coat Z. The Zimmermann Coat-Z brake disc provides a protective coating that prevents rust and corrosion, extended rotor life and improved visual appearance. To improve the rust protection during storage and usage, Otto Zimmermann GmbH implements this new Coat-Z technology step by step in its production range. Beside the still optimum function of the brake disc, this coating ensures a consistent attractive appearance. Zimmermann brake discs are usually made of cast iron (with flake graphite) of different qualities; they correspond to the material used for the original spare parts. Therefore, the utilization of such materials (referred to as High Carbon by the competition) has always been a matter of course for Otto Zimmermann.

Product Features:

Coat-Z protective anti-corrosion coating
No formation of rust at the hub and herewith improved visual appearance
Immediate functional capability without removal of the coating before mounting
Excellent deceleration action and no distortion of friction ring at high temperatures
Substantial weight saving and therefore less unsprung mass
Floating mounting enables radial expansion of the brake disc under relatively heavy loads, thus preventing shielding and increasing resistance to heat cracks
Hot spots prevented by optimized design of ventilation channels
1:1 exchange of original disc possible
Not subject to registration: general ABE certification supplied with disc
No conversion required for brake tuning

from

$1.61

Parking Brake Shoe Spring

from

$1.21

Oil Drain Plug Gasket

from

$140.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$147.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$562.43

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$682.99

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$688.49

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$53.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$484.70

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$53.99

Carquest Premium Brake Calipers are manufactured to meet or exceed original equipment manufacturer specifications for performance and durability. Where applicable, Carquest Premium Brake Calipers feature a specially formulated OE style zinc di-chromate anti-corrosion finish that provides superior rust protection in all conditions. Carquest Premium Brake Calipers feature new OE design, stainless steel pistons manufactured for maximum durability, and precision machined for an exacting fit and smooth application of braking force. Carquest Premium Brake Calipers include 100% new OE design dust boots and EPDM rubber seals that provide increased resistance to thermal deterioration and years of-leak free operation. Carquest Premium Brake Calipers include application-specific brackets and abutment hardware where required, for easy installation and confident restoration of stopping power. 100% end-of-line inspection and pressure testing guarantees perfect performance right out of the box.

Product Features:

Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
Meets or exceeds original equipment specifications for performance and durability
OE design stainless steel pistons provide maximum durability and are precision machined for a perfect fit in the caliper body
Application-specific caliper bodies for easy installation
Brackets included where required, for complete system restoration
OE style, zinc di-chromate anti-corrosion finishes provide superior resistance to rust on all iron caliper bodies and brackets
100% new, OE style rubber dust boots and EPDM rubber seals for improved resistance to thermal deterioration and cracking
New bleeder screws, banjo bolts, and crush washers included for a complete repair
OE Style, stainless steel pad abutment hardware included
100% end-of-line inspection and pressure testing ensures quality and performance
Caliper finish or coating may vary

from

$12.99

Brakes are designed as a system and all the parts need to work together for best performance. The kits provide advance protection for your brake by assuring brakes perform at an optimum level.

Product Features:

This part matches Original Equipment (OE) quality specifications
Exact fitment and original replacement
Helps deliver a quieter, more efficient braking system
Low-friction PTFE coating to reduce drag
Manufactured with quality materials to suppress high stress levels

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$11.35

This is a brake hardware kit consisting of (4) 000 991 03 60 brake pins and (2) 000 421 02 91 anti-rattle spring. The ATE Brake Pad Pin is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features: