1980 GMC K1500 Performance Engines

Product Features:

• Valve Cover Gasket

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

• Advance the cam for increased torque and horsepower
• Tune your powerband for more end torque or increase top end horsepower
• Includes (4) offset bushings and (1) 0 degree bushing
• Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
• Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
• Increase Top-End Horsepower

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

use Performer 2-O #2161.

Product Features:

• 2500 to 6500 RPM High Performance Street Engines
• Single-Plane Low-Rise Intake Good for High RPM
• Ideal for Applications with Limited Hood Clearance
• For Top-End HP and Adequate Throttle Response
• Not for Mileage or Emissions Applications
• Use with Large Oval Port Heads (1975 and Earlier)
• Will fit Under Corvette Hood Without Modifications
• Not For Tall Block V8 Engines

Edelbrock part #9646 Pushrods are designed for small-block Chevy V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise forme

Product Features:

• 7.25 in. Length
• 0.312 in. Diameter
• 4130 Chromoly Steel Material
• Black Oxide Finish
• Made In The USA

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

• Fits Chevy engines
• Includes a 1/2 inch NPT threaded hole for by-pass hose
• Includes bolts
• Chrome plated
• Easy to install
• O-ring/gasket not included

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

Product Features:

• HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.
• 279/296 Advertised Duration, 227/241 Duration @ .050″, .498″/.483″ Lift, 107 Lobe Separation
• Valve spring upgrade required

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Product Features:

• Made of aluminum with a natural finish
• 100cc chambers with 290cc intake ports
• 2.19 in. intake and 1.88 in. exhaust valves
• Bare Cylinder Head
• Standard intake and exhaust port location

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection

Mr. Gasket screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street applications. OE style press in rocker studs can actually pull out of the cylinder head when using high lift camshafts. Includes sixteen studs 3/8-24 x 1.47 inch long top x 7/16-14 bottom.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Grade 8 Steel

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

• Cylinder Head Bolts
• Longer-Than-Stock
• High Quality Grade 8 Alloy
• Increase Torque Settings
• Higher Clamp Loads On Gasket

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.O.D. Dia. 1 I.D. Dia. 2 Damper Seat Load Open Load Coil Bind Rate (Lbs./In.) Titanium Retainer Steel Retainer Cup Seat Shims 1.524 1.110 Y 122 @ 1.900 309 @ 1.400 1.200 373 721, 732 1732, 741 4779* 4757

Product Features:

• Seat pressure: 122 lbs. @ 1.900″, Open Pressure: 309 lbs. @ 1.400″
• O.D.: 1.524″, I.D.: 1.110″
• Single valve springs with damper

Manufactured from cellulose/nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile rubber composition gasket material
• Provides excellent sealing and durability
• Complete with molded rubber front/rear oil pan end seals where applicable
• For OE replacement, high performance street, drag race and oval track use
• Graphite Non-Wicking Rubber
• No Cork Particles
• Easy Removal For Disassembly

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Holeshot 2400 for GM 1998 to 2002 4L60E Camaro and Firebird with an LS1 engine Application: GM 1998 to 2002 4L60E Camaro and Firebird with LS1 A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benef

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

This Mr. Gasket Water Pump Bolt Set includes chrome plated grade 5 hex head fasteners to install the water pump on your small or big block Chevrolet with the long style water pump. Includes four 3/8 inch-16 x 2 inch bolts with four 3/8 inch AN washers. AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

• Chrome Plated
• Grade 5
• AN washers with no exposed shoulder for a professional appearance

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

• Twisted Snout Water Pump Design For Updated Style
• Street Performance
• Heavy Duty Shaft w/5/8 in. Pilot
• Six-Blade Stamped Steel
• Anti-Cavitation Impeller
• 100 Percent Leak Tested

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

• Twisted Snout Water Pump Design For Updated Style
• Street Performance
• Heavy Duty Shaft w/5/8 in. Pilot
• Six-Blade Stamped Steel
• Anti-Cavitation Impeller
• 100 Percent Leak Tested