from

$11.99

9″ Ford gasket.

Product Features:

Dropout gasket
Fits Ford 9″

from

$313.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Ford 9″
9.00″ ring gear diameter
28 spline pinion
10 ring gear bolts
6.50 ratio

from

$215.99

Bearing race driver for Dana 44 rear. (TK 31520) No return.

Product Features:

Bearing race driver
Fits 31520 race
All steel construction

from

$167.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 2009 and down Ford 8.8″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$49.99

Product Features:

USA Standard Gear heavy-duty cross pin shaft
Fits Ford 9″
Works with Spartan Locker or standard open spider gears
Long shaft

from

$57.99

Product Features:

Fits Ford 9″ with 31 spline axles
Installs into a standard open carrier case
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$729.99

9″ Yukon 3.062″ aluminum case, HD dropout housing with forged caps. The Yukon aluminum dropouts feature a adjuster lock which is offset 90 degrees, offering an uninterrupted bearing cap for higher strenth. Made from A356-T6 aluminum and featuring a through-bolt desgin, this dropout is built for high horsepower & tall tires.Rated up to 1000HP!

Product Features:

Fits Ford 9″
3.062″ carrier race diameter
A356-T6 aluminum
Thru-bolt design added strength

from

$203.99

Yukon yoke (short, for Daytona support) for Ford 9″ with 28 spline pinion and a 1330 U/joint size. 4″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″
28 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.125″ cap diameter
U-bolt style

from

$4.99

Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with Trac Loc limited slip
1.25″ long

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$5.99

Fine thread pinion support bolt (aftermarket aluminum only) for 9″ Ford.

Product Features:

Pinion support bolt for Ford 9″
3/8″ x 24 thread
1.5″ long

from

$48.99

RngPnnInstlKt

from

$8.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$1302.99

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

Fits Dana Spicer 44 with 30 spline axles
3.73 and down ratio only
Forged case and 8620 internals for added strength
Works with a variety of air delivery systems
Assembled in the USA

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$941.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

Fits Ford 8″ with 31 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$51.99

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

Carrier race
Fits Ford 9″
Conversion race to install small bearing carrier into 3.250″ dropout

from

$209.99

Product Features:

Spider gear kit
Fits Ford 8.8″ 31 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$31.99

Product Features:

MINI SPOOL 8″ & 9″ 31 SPLN STL 090431

from

$119.99

8.8″ FORD 09 & DWN PINION KIT .

Product Features:

Fits 2009 and down Ford 8.8″
Uses Koyo bearings and races
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$23.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 25, 27, 30, 44 and 50

from

$8.99

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

Pinion gear thrust washer
Fits Ford 8.8″
0.750″ I.D.

from

$127.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features: