Name: Hei Remote Mount Super Coil
Brand: Accel
SKU: 140024
Price: 65.99 USD
Rating: 5.0 (7 reviews)

from

$65.99

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Can also work with CD ignition systems. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Comes complete with new mounting hardware. High dielectric strength ACCEL yellow over molded housing. Output is 48,000 volts with 0.2ohms resistance.

Product Features:

Remote Mount Ignition Coil
Higher Energy/Voltage Outputs
Quicker Starts
Improved Throttle Response
More High RPM Power
Increase Energy Transfer
Resist Corrosion
W/New Mounting Hardware

from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

Universal Floor Mount Application
Base Trimmed For Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$83.29

Billet aluminum handle with flexible braded steel tube mounts to the firewall. 29-3/4 inch long.

Product Features:

Braided Stainless Steel
Firewall Mounting
Includes Oil Fill Tube

from

$620.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet Flow Tested By Holley Technicians
Arrives Ready To Run

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$302.99

Fabricated from lightweight aluminum and features a smooth top with a baffled opening and long mounting bolts. Has 1/4 inch thick 1-piece mounting flange which ensures a flat mating surface along with aluminum tubes welded into the mounting holes to maintain rail flatness and increase valve cover strength. Includes mounting hardware.

Product Features:

Fits big block Chevy engines
Welded aluminum construction
1/4″ thick 1-piece mounting flange for superior sealing
Includes mounting hardware
Tall design cover for added rocker clearance
Silver anodized finish
Has 1.25″ breather openings
Sold as a pair
These could have valvetrain interference issues if installing on Dart Pro 1 cylinder heads.

from

$518.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$149.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$376.99

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts. Ideal for use with higher compression ratio engines that

Product Features:

Best with aftermarket torque converters and 9.5:1 compression.
Great high RPM power.
Easy on valve train parts.
Can be used with mild ratio rocker arms and traditional performance valve springs.

from

$42.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$27.49

These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.

Product Features:

Assures Accurate Torque App
Prevents Galling Manifold
Grade 5 Material
Black Oxide Coasted

from

$144.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 110 gph Free Flow
Shutoff Pressure Pre-Set From 6.5 To 8 PSI
Fuel Pressure Regulator Is Not Required
Heavy Duty Construction For Continuous High rpm Operation
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT
Inlet/Outlet Tapped For 3/8 in. NPT

from

$766.99

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

2800-3200 RPM
Small And Big Blocks
Serious Performance
Furnace Brazed
Fully Balanced

from

$20.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$23.79

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

Fits Chevy engines
Includes a 1/2 inch NPT threaded hole for by-pass hose
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$62.99

The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$25.99

Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:

Chrome Plated Steel
F-Style
Heavy Gauge Steel Construction
Fits Small Block Chevy 265-400 CID
Must Be Used With Part 9852

from

$34.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$154.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$36.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$49.49

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

Fits MSD/GM V8 Distributors
Made from high quality materials
Brass terminals
High dielectric properties

from

$62.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$10.99

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi

Product Features:

PerTronix D4260 Flame-Thrower Distributor Rotor HEI/EST Black
Made from hi-performance 60 KV rated alkyd molding compound.

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.