1979 Toyota Pickup Differentials

8″ standard Open side gear Thrust washer.

Product Features:

• Side gear thrust washer
• Fits Toyota 8″ with 4 cylinder engine

V6 standard Open pinion gear Thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits Toyota V6

Toyota 8″ & V6 gasket.

Product Features:

• Dropout gasket
• Fits Toyota 8″ and V6

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits standard rotation Toyota 7.5″ with 4 cylinder engine
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

• Fits Toyota 8″ with 4 cylinder engine
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

8″ Toyota Spartan locker cross pin.

Product Features:

• USA Standard Gear heavy-duty short cross pin shaft
• Fits Toyota 8″ with 4 cylinder engine
• Works with Spartan Locker or standard open spider gears

Product Features:

• Roll pin
• Fits Toyota 8″ with 4 cylinder engine

Bearing race driver for rear Toyota V6, Landcruiser reverse rotation, and Tacoma with locker. (TOY35028). No return.

Product Features:

• Bearing race driver
• Fits 35028 race
• All steel construction

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Preload shim kit for Toyota Landcruiser. Also compatible with Toyota 8″ 4 cylinder & V6 with a solid spacer.

Product Features:

• Preload shim kit
• Fits 9.5″ Toyota Landcruiser

Yukon yoke for Toyota 7.5″ IFS (and ’85 and newer rear) with 23 spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Toyota 7.5″
• 23 spline

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using high-quality materials for durability and performance
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. This kit fits applications with a 29 spline pinion.

Product Features:

• Fits Toyota V6 rear
• 29 spline only
• Included are KOYO bearings and races along with high quality seals and small parts.
• Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and gasket.

Axle shaft damaged or bearings worn out: This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Product Features:
• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

Limited Slip Dffrntl

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Air line repair kit, ZIP locker.

Product Features:

• Air line repair kit
• Includes 20′ air line and two repair fittings

Product Features:

• MINI-INSTALL TOYOTA 8″

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

8″ Reverse high-pinion Toyota Drop Out (fits 8″ Housing) .

Product Features:

• Fits Toyota Landcruiser reverse rotation front

Mobil 1 Synthetic Gear Lubricant LS 75W-90 is a supreme, multi-purpose automotive gear lubricant that helps to provide exceptional thermal stability and resistance to high temperature oxidation, extending gear life due to minimal deposits. Helps to deliver outstanding protection against low speed/high torque wear with the capability to handle severe driving conditions while delivering smooth efficient performance. Mobil 1 Synthetic Gear Lubricant LS provides exceptional shear stability, corrosion protection, and enhanced frictional properties. Compared to conventional hypoid gear lubricants, Mobil 1 LS 75W-90 performs exceptionally over a wide range of temperatures to reduce wear at start up. Mobil 1 gear lube helps to minimize leakage and reduce contamination while providing good resistance to foaming to maintain film strength for reliable lubrication. Meets or exceeds the requirements of the following industry specifications: API GL-5.

Product Features:

• Mobil 1 LS synthetic automotive gear lubricant exceeds the highest level of performance requirements of modern passenger vehicles
• Helps to provide exceptional thermal stability and resistance to high temperature oxidation and extend gear life due to minimal deposits
• Delivers outstanding protection against low speed/high torque wear, handling severe driving conditions with smooth, efficient performance
• Compared to conventional hypoid gear lubricants, performs exceptionally over a wide range of temperatures to reduce wear at start up
• Provides exceptional shear stability, corrosion protection, and enhanced frictional properties
• Manufacturer Part Number: 104361

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Low swell in hydrocarbon fluids
• Design type: spring loaded; multi-lip
• Provides good low temperature capability
• Temperature range: -40°F to 225°F; -40°C to 107°C
• Delivers quality and reliable performance for every type of repair

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 44 and Toyota 8″ and V6

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), pinion shim kit, marking compound and brush. No side shims.

Product Features:

• Fits Toyota 7.5″ front with 4 cylinder engine
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

Product Features:

• PIN. NUT TOYOTA FRT&REAR