from

$697.37

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$489.65

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$29.99

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

Wearever Brake Shoes come bonded or riveted based on OE design.
Wearever Brake Shoes are coated to prevent rust.
Wearever Brake Shoes are 100% New not remanufactured.
Brand may vary by location

from

$32.10

Parking Brake Shoe

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$67.17

Brake Hardware Kit

from

$24.75

The ATE disc brake hardware kits provide everything you need to perform a complete the brake job and restore the brake system back to the optimal operating condition.

Product Features:

Reduced Brake Noise, comebacks and unsatisfied customers,
Extends the life of a brake job,
Improved fuel mileage, and
Restores brakes to like new Performance. Effects of Corrosion, Heat, Stress, Use Rust and Corrosion on floating caliper slides or bushings can prevent the caliper from centering properly, which can
reduce effective braking force
cause uneven pad wear, and brake noise. Rubber Bushings lose there resiliency and become flattened from the torque of the braking system which can
cause excessive caliper movement
cause unwanted noise like rattles and thumps. New Hardware = Back to like-new performance

from

$197.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$122.99

CARDONE Remanufactured Power Brake Boosters are re-engineered, built and tested to match O.E. performance. Original designs are scrutinized for potential improvement and, where applicable, design upgrades are implemented to produce a more durable part than the original. All units are 100% tested to ensure perfect fit and function.

Product Features:

100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
Exclusive rust-prohibitive finishing process extends unit life.
Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
All units are 100% tested to ensure reliable performance.
Guaranteed fit and function.

from

$736.28

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$697.81

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$13.06

The Original Equipment Clutch Return Spring is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$46.99

Carquest Wearever Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

Application-specific formulations designed for extended pad life and clean wheels
Multi-layer shim for near silent braking
OE designed slots and chamfers for consistent performance
Hardware included on popular and late-model applications

from

$65.85

Bosch QuietCast Premium raises aftermarket brake pad technology to a whole new level. Employing the industry’s best pre-attached, rubber core shims and Molded Shim Technology (on selected applications), QuietCast delivers the quiet operation you and your customers expect with the durability and long life that are the hallmarks of all Bosch products. Every Bosch QuietCast Disc Brake Pad is fitted with the industry’s best pre-attached rubber core shim. This shim style is the most predominant type used by OE manufacturers and is exclusively offered by Bosch for the independent aftermarket.

Product Features:

OE-Equivalent and Direct Fit application.
OE style rubber-core shims
Advanced, platform-specific Semi Metallic formulation
Dedicated engineers source and rigorously test all friction materials and formulations
Manufactured under the same exacting quality standards as OE components and system
Powder-coated backing plate
Rigorous physical and dynamometer testing
Synthetic lubricant in box
Pads individually wrapped Bosch Molded Shim Technology (MST)*** (On Select Applications)
At the time of pressing, heat, adhesive and pressure mold the multi-layer shim to the backing plate and friction material creating an integrally molded unit.
Shim stays attached throughout the life of the pad; won’t walk or slide on the backing plate
Provides maximum stability resulting in quieter shim performance over the life of the pad

from

$1.21

Oil Drain Plug Gasket

from

$43.99

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

Application-specific friction formulations provide shorter stopping distances and extended pad life
Hardware included for most applications, provides better value and
OE-designed slots and chamfers to reduce noise and vibration
Multi-layer shim provides near silent braking
Powder-coated backing plate prevents corrosion

from

$63.99

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Stainless steel hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking
Includes Premium stainless-steel hardware for easy installation

from

$67.99

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking
Includes Premium hardware for easy installation

from

$38.96

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$18.08

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$46.21

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$238.99

The Sebro coated brake disc is an OE-Quality replacement that is manufactured to withstand the higher demands of braking extremes from today’s high performance European vehicles. For the sustainable improvement of corrosion protection and also for good looking our break discs are silver grey coated in the pot- and outer diameter area. By the automatic coating process a high quality with steady coating thickness is guaranteed. In the uncoated areas all components are provided with suitable corrosion protection.

Product Features:

OE-Equivalent and Direct fit Application
high carbon content disc
Protective coating that resists corrosion
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Improved thermal efficiency

from

$89.99

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to prevent warping
Air gap eliminates brake fade and increases pad life
Non-Directional finish decreases break-in time

from

$598.23

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

OE-Equivalent and Direct fit Application
made of special cast iron with high carbon content
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Contains the same high quality craftsmanship as the original equipment manufacturer.
Guarantees OE quality performance, durability and fitment.

from

$756.75

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

OE-Equivalent and Direct fit Application
made of special cast iron with high carbon content
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Contains the same high quality craftsmanship as the original equipment manufacturer.
Guarantees OE quality performance, durability and fitment.

from

$288.58

The Sebro coated brake disc is an OE-Quality replacement that is manufactured to withstand the higher demands of braking extremes from today’s high performance European vehicles. For the sustainable improvement of corrosion protection and also for good looking our break discs are silver grey coated in the pot- and outer diameter area. By the automatic coating process a high quality with steady coating thickness is guaranteed. In the uncoated areas all components are provided with suitable corrosion protection.

Product Features:

OE-Equivalent and Direct fit Application
high carbon content disc
Protective coating that resists corrosion
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Improved thermal efficiency

from

$118.99

Carquest Premium painted brake rotors meet or exceed original equipment (O.E.) specifications, delivering superior stopping power with proper harmonic design and non-directional finish that eliminate noise. Carquest Premium painted rotors feature RotorShield, a rust-inhibiting barrier that provides up to 5 times more protection than non-painted rotors. The RotorShield barrier is applied to the rotor hat to protect from unsightly rust and help maintain a like-new appearance. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of the pads and rotors. Carquest Premium painted brake rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to prevent warping
Air gap eliminates brake fade and increases pad life
Non-directional finish decreases break-in time

from

$190.73

The Sebro coated brake disc is an OE-Quality replacement that is manufactured to withstand the higher demands of braking extremes from today’s high performance European vehicles. For the sustainable improvement of corrosion protection and also for good looking our break discs are silver grey coated in the pot- and outer diameter area. By the automatic coating process a high quality with steady coating thickness is guaranteed. In the uncoated areas all components are provided with suitable corrosion protection.

Product Features: