1979 Ford LTD Performance Engines

Essential 1979 Ford LTD Performance Engines

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)

Ultra Seal: Harmonic Balancer Bolt/Washer Kit

from

$38.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:
  • Heat treated black oxide coated Grade 8 alloy steel
  • Thick parallel ground washer provides more accurate, uniform torque
  • Hex Prevents Socket Slippage
  • Accurate And Uniform Torque
  • Black Plated Finish
See More

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2941)

Engine Crankshaft Seal Kit

from

$48.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Sure Seat Valve Springs for Ford 351W V8 (Part No.5982)

Sure Seat Valve Springs for Ford 351W V8

from

$44.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Mr. Gasket – Cam Change Gaskets (Part No.4410)

Cam Change Gaskets

from

$63.09
If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:
  • Contains all the gaskets needed to change out your camshaft
  • Fuel Injector O-Ring Not Included
  • Meets Performance Standards
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)

Engine Valve Cover Gasket Set

from

$25.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Die cut silicone rubber gaskets conform to out-of-flat covers
  • Great for on-again/off-again situations
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1817)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Competition Cams – High Energy/Marine 218/218 Hydraulic Flat Cam and Lifter Kit (Part No.CL34-227-4)

High Energy/Marine 218/218 Hydraulic Flat Cam and Lifter Kit

from

$426.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST

from

$237.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:
  • Cost effective aluminum construction provides superior strength to weight ratio
  • Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
  • Durable design increases valve lift while withstanding the rigors of moderate race use
  • Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
See More

Mr. Gasket – Head Gasket (Part No.1132G)

Head Gasket

from

$37.59
Mr. Gasket Embossed Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. This is a very unique design that has a solid metal on metal fold at the combustion seal. This fold makes for a very stout seal that is almost the equivalent of a higher-end MLS (multi-layer steel) gasket with a gas stopper layer, but at a much lower cost. This gasket also has embossments around the coolant and oil passages and has a thick aluminum flake coating. All of these features result in a steel shim head gasket that handles extreme cylinder pressures very well. It’s probably the best steel shim head gasket you could ask for. Sold individually.

Product Features:
  • Embossed steel with aluminum flake coating
  • Solid metal over metal fold at the combustion seal
  • Embossed seals at coolant and oil passages
  • Approximately .020″ compressed thickness
  • For high performance street, drag race and oval track use.
See More

Spectre – Water Neck; Ford 429-460 (Part No.4734)

Water Neck; Ford 429-460

from

$54.99
Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:
  • Fits Ford 429 – 460 engines
  • Has a 3/8 inch NPT threaded hole for temperature sensor
  • Includes sealing O-ring
  • Chrome plated
  • Easy to install
  • Hardware not included
See More

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

289-302 Ford Head Bolt Kit

from

$107.99


Product Features:
  • Highest Quality Head Bolts
  • Cold-Formed/Heat Treated
  • Ensures Molecular Integrity
  • Reduced Diameter Bolt Heads
  • Hardened/Parallel-Ground Washers Included
  • Rated At 170000 psi
  • Manufactured By ARP
See More

Edelbrock – Water Pump Ford 1965-67 289 cid (Part No.8842)

Water Pump Ford 1965-67 289 cid

from

$285.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Super Intake Manifold Bolts

from

$43.99
Super Intake Manifold Bolts

Edelbrock – Pushrod Set for Ford 289-302 (Part No.9655)

Pushrod Set for Ford 289-302

from

$208.99
Edelbrock part #9655 Pushrods are designed for small-block Ford 289-302 V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precis

Product Features:
  • 6.4 in. Length
  • 0.312 in. Diameter
  • 4130 Chromoly Steel Material
  • Black Oxide Finish
  • Made In The USA
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Performer Series Retainer (Qty 16)

from

$100.99
Product Features:
  • Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

B & M – Torque Converter, Tork Master 2400 (Part No.50441)

Torque Converter, Tork Master 2400

from

$450.99
A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength. Due to torque converter co

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

B & M – Torque Converter, Tork Master 2400 (Part No.40438)

Torque Converter, Tork Master 2400

from

$605.99
A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
  • Washer Between Turbine and Cover
See More

Edelbrock – Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" (Part No.60399)

Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02"

from

$1035.99
Product Features:
  • Complete Single For Flat Tappet
  • 60cc Combustion Chamber Volume
  • 170cc Intake/60cc Exhaust Runner Volume
  • 2.02 in. Intake/1.60 in. Exhaust Valve Diameter
  • 0.625 in. Deck Thickness
See More

Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90" (Part No.60379)

Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90"

from

$1035.99
Product Features:
  • Capable of 300 plus horsepower when matched with the Edelbrock Performer Power Package
  • 1.90 in. intake valves are for use with stock pistons
  • Exhaust valve is 1.60 in.
  • 60cc combustion with 170cc intake port
  • Flat Tappet Camshaft Type
See More

Edelbrock – Intake Manifold Gasket for 1963-1996 Small-Block Fords (Part No.7220)

Intake Manifold Gasket for 1963-1996 Small-Block Fords

from

$28.99


Product Features:
  • Clean Positive Seal
  • Embossed Silicone Bead Surrounding The Port
  • Matched To Manifolds And Cylinder Heads
See More

Mr. Gasket – Intake Gasket (Part No.203G)

Intake Gasket

from

$36.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals and distributor gasket where applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Competition Cams – Mutha’ Thumpr 235/249 Hydraulic Roller Cam (Part No.32-601-8)

Mutha' Thumpr 235/249 Hydraulic Roller Cam

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam (Part No.31-238-3)

Xtreme Energy 218/224 Hydraulic Flat Cam

from

$257.99
HYDRAULIC – Xtreme Energy: Excellent response, good mid-range, stock converter, 3.23-4.10 gear.

Product Features:
  • HYDRAULIC – Xtreme Energy: Excellent response, good mid-range, stock converter, 3.23-4.10 gear.
  • 262/270 Advertised Duration, 218/224 Duration @ .050″, .493″/.500″ Lift, 110 Lobe Separation
  • Valve spring upgrade required
  • 289-302 Firing Order
See More

Edelbrock – Victor Jr. 302 Intake Manifold Small-Block Ford (Part No.2921)

Victor Jr. 302 Intake Manifold Small-Block Ford

from

$451.99
Race winning design for all types of competition. Single plane maximizes torque and horsepower. Runners feature extra material for custom porting. For performance in 3500 to 7500 RPM range. For modified OE or aftermarket Windsor aluminum heads. Match with Edelbrock heads for maximum performance. Port exits can be opened to 2.10 x 1.18 inch. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:
  • Race Winning Design for all Types of Competition
  • Single Plane Maximizes Torque and Horsepower
  • Runners Feature Extra Material for Custom Porting
  • For Performance in 3500 to 7500 RPM Range
  • For Modified OE or Aftermarket Windsor Alum Heads
  • Match with Edelbrock Heads for Max Performance
  • Port Exits Can be Opened to 2.10 x 1.18 in.
See More

Edelbrock – Performer 460 Intake Manifold #2166 for Ford 429/460, Non-EGR, Satin Finish (Part No.2166)

Performer 460 Intake Manifold #2166 for Ford 429/460, Non-EGR, Satin Finish

from

$397.99
Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • Accepts Late-Model Choke; Waterneck; and HEI
  • Accepts A/C And Alternator
  • Accepts Exhaust Heated Chokes
See More

Edelbrock – Torker II 460 Big Block Ford Intake Manifold (Part No.5066)

Torker II 460 Big Block Ford Intake Manifold

from

$473.99
2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Available in cast or polished.

Product Features:
  • 2500 to 6500 RPM High Performance Street Engines
  • Single-Plane Low-Rise Intake Good for High RPM
  • Ideal for Applications with Limited Hood Clearance
  • For Top-End HP and Adequate Throttle Response
See More

1979 Ford LTD Performance Engines

Maybe you’re in the middle of a full rebuild of that 1979 Ford LTD. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 60 different Performance Engines in our inventory ranging from $19.99 to $1,035.99. That means you can find the exact parts or products you need to keep that 1979 Ford LTD running smoothly.

Performance Engines are only as good as their brand. We stock 5 different brands to make sure you have plenty of trusted parts to choose from for your 1979 Ford LTD. Mr. Gasket, FEL-PRO Performance, and Edelbrock are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1979 Ford LTD, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 246 reviews in this category, some of the top rated parts include 289-302 Ford Head Bolt Kit with 2.0 stars and Torker II 302 Intake Manifold Small-Block Ford with 2.0 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1979 Ford LTD rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1979 Ford LTD Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1979 Ford LTD demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your LTD the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular FEL-PRO Performance Performance Engines

We carry FEL-PRO Performance parts in our stock across Performance Engine Intake Manifold Gaskets and Performance Engine Valve Cover Gasket Sets categories, plus more. For a 1979 Ford LTD, our most popular FEL-PRO Performance Performance Engines include:
Lower Intake Manifold Gasket Set: 11 Piece Set
from $33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets
Engine Valve Cover Gasket Set
from $46.99
(1)
Engine Valve Cover Gasket Set
Performance Engine Valve Cover Gasket Sets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $51.99
(2)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets

FAQs for 1979 Ford LTD Performance Engines

What are the most purchased Performance Engines for the 1979 Ford LTD?

Out of 60 Performance Engines for the 1979 Ford LTD, the most popular in our inventory are:
Intake Manifold Gasket for 1963-1996 Small-Block Fords
from $28.99
(1)
Intake Manifold Gasket for 1963-1996 Small-Block Fords
Performance Engine Intake Manifold Gaskets
Performer-Link Adjustable True-Roller Timing Chain Set
from $67.99
This product is not rated
Performer-Link Adjustable True-Roller Timing Chain Set
Performance Engine Timing Sets and Components
Ultra Seal: Harmonic Balancer Bolt/Washer Kit
from $38.49
This product is not rated
Ultra Seal: Harmonic Balancer Bolt/Washer Kit
Performance Engine Harmonic Balancers

What are the top-rated 1979 Ford LTD Performance Engines?

Top-rated Performance Engines for your 1979 Ford LTD based on customer reviews/ratings are:
289-302 Ford Head Bolt Kit
from $107.99
(7)
289-302 Ford Head Bolt Kit
“Great quality bolts. They include thread locker. Would definitely recommend to anyone replacing their heads.”
Torker II 302 Intake Manifold Small-Block Ford
from $376.99
(1)
Torker II 302 Intake Manifold Small-Block Ford
“Nice looking product but mine was a used store return so I returned it.”
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
from $237.99
(1)
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
“These things break very easy. Not a big fan of the soft brass when trying to install them with the screwdriver head they use. Change it hex and it woy”