1979 Chevrolet C10 Air Intakes
More 1979 Chevrolet C10 Air Intakes Categories
If you’re looking for an original Air Intakes replacement for a 1979 Chevrolet C10, you can search through our selection below. You’ll also find aftermarket and OEM Air Intakes to meet your needs.
Essential 1979 Chevrolet C10 Air Intakes
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Performer EPS Intake Manifold for 1955-86 Small-Block Chevy, Black Finish (Part No.27013)
from
$360.99
Edelbrock part #27013 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr
Product Features:
See More
Product Features:
- Idle-5500 RPM Range
- Dual Plane Type-4150 Style Flange
- 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
- Black Powder Coated Finish
- Non-EGR
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Standard Main Jet Carburetor Metering Jet #12458 Size .057 (Pair) (Part No.12458)
from
$13.99
The Edelbrock 94 #12458 Carburetor Jets .058″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 58 Maximum Jet Size
- 0.057 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 90240-2)
from
$21.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
- Includes all parts needed to complete the repair
Felpro – Carburetor Mounting Gasket (Part No.60250)
from
$6.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
United Carb – Remanufactured Carburetor 4 Barrel (Part No.3-3676)
from
$414.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Felpro – Carburetor Choke Tube Gasket (Part No.72587)
from
$1.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$43.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)
from
$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers
Product Features:
See More
Product Features:
- Zinc plated to resist corrosion and provide a clean professional appearance
- Made from Grade 5 steel for strength and durability
- Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
- Allen (socket) Head
- Zinc Plated For Protection
Edelbrock – Triple Carburetor Fuel Log Kit #1288 with 5-1/2 in. Outlet Spacing (Part No.1288)
from
$99.99
This Edelbrock Fuel Log kit #1284 is an exact replica of the original design used by Vic Sr. in the 1950’s. They are made from extruded aluminum tube with a 3/8″ threaded outlet at each end and a polished finish. Kit includes, black neoprene hose, Corbin
Product Features:
See More
Product Features:
- Polished Log
- Brass Fittings
- Black Neoprene Hose
- 5-1/2 in. Outlet Spacing
- Includes Hose Clamps
Felpro – AIR CLEANER MOUNTING GASKET (Part No.60357)
from
$2.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – AIR CLEANER MOUNTING GASKET (Part No.60555)
from
$3.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$12.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Carburetor Accelerator Pump Diaphragm #12401 50cc (Part No.12401)
from
$31.99
Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Product Features:
See More
Product Features:
- Rubber Material
- For Holley®, Barry Grant, And Demon Gasoline Carburetors
- No Hardware Included
- 50cc Volume
- Made iIn The USA
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1142)
from
$93.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1137)
from
$55.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$186.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Dorman – Breather Element Clips – GM 2002-76-Use with breather elements: AC; FB59: Fram; CA19: Purolator; AF9 (Part No.41251)
from
$1.99
Breather Element Clips – GM 2002-76-Use with breather elements: AC; FB59: Fram; CA19: Purolator; AF9
Dorman – Help – Breather Element Clips – GM 2002-76-Use with breather elements: AC; FB59: Fram; CA19: Purolator; AF9 (Part No.41113)
from
$1.49
This air cleaner fastener is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this air cleaner fastener is designed to match the fit and function of the original part on specified vehicles
- Ideal solution – this fastener is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$24.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1741)
from
$22.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Edelbrock – Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (Part No.12750)
from
$43.99
Product Features:
See More
- The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4160 style Carburetor.
Carquest – Carburetor Kit (Part No.96-422)
from
$42.05
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$62.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Popular 1979 Chevrolet C10 Air Intakes Categories
1979 Chevrolet C10 Air Intakes
You count on your 1979 Chevrolet C10 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Air Intakes. With 113 Air Intakes ranging in price from $1.49 to $1,776.99, you’re sure to find everything you need for your 1979 Chevrolet C10.
Brands matter. If you want to shop a specific Air Intakes brand, we stock 11 different brands like Felpro, Edelbrock, and Mr. Gasket. 1979 Chevrolet C10 Air Intakes start as low as $1.49!
One of the best ways to find top quality OEM or aftermarket Air Intakes is by asking professionals. Short of that, you can shop with confidence thanks to our 951 extensive product reviews on 1979 Chevrolet C10 Air Intakes. Some of the top-rated Air Intakes products we carry are Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.4 stars and Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs with 4.5 stars.
Did we mention you can order your Air Intakes from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Air Intakes inventory for your 1979 Chevrolet C10 below to get started!
Top-Rated Air Intakes Brands For Your 1979 Chevrolet C10
Trusted Air Intakes OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1979 Chevrolet C10 running right for years to come. In our inventory you’ll find brands like Felpro, Edelbrock, Mr. Gasket, and even more.
Popular Felpro Air Intakes
You’ll find popular Felpro brand products across Air Cleaner Parts and Carburetor Parts. All are waiting to get your 1979 Chevrolet C10 back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated Edelbrock Air Intakes
If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Air Intakes for your 1979 Chevrolet C10, and some of our most reviewed Edelbrock parts include:
from
$16.99
(27)
Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg
Carburetor Power Valves
from
$43.99
(19)
Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
from
$446.99
(10)
AVS2 1906 Carburetor: 650 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
FAQs for 1979 Chevrolet C10 Air Intakes
What are the most purchased Air Intakes for the 1979 Chevrolet C10?
Out of 113 Air Intakes for the 1979 Chevrolet C10, the most popular in our inventory are:
from
$47.99
(9)
Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
What are the top-rated 1979 Chevrolet C10 Air Intakes?
Top-rated Air Intakes for your 1979 Chevrolet C10 based on customer reviews/ratings are:
from
$451.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
from
$49.49
(5)
Ultra Seal: Intake Gasket
“I bought this to replace the CV Axle because the inner boot on my old axle was flinging grease. This part was a perfect replacement for my 2008 Honda ”
