from

$289.99

Product Features:

Fits GM 8.2″ Buick, Oldsmobile and Pontiac
Adapt GM gears for BOP housing

from

$481.99

7.625″ GM standard Open case, 3.23 & up, Large & SM windows, loaded. 28 Spline.

Product Features:

Standard open carrier case and spiders
7.5″ & 7.625″ 28 spline applications
3.23 and up ratio only
Large and Small windows

from

$49.99

Standard open cross pin (0.795″ diameter) for 8.5″ GM. fits some Eaton positractions.

Product Features:

Cross pin shaft for GM 8.5″ and 8.6″
Fits standard open differentials only
0.795″ diameter

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$94.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

KIT BRG & SEAL GM 8.5″ ‘P’ AXLE

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$203.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1982-1999 GM 7.5″ and 7.625″
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$2.79

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$10.99

Product Features:

Clutch guide
Fits GM 7.5″ and 7.625″ Dura Grip

from

$43.99

RngPnnInstlKt

from

$153.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits 8.2″ Buick, Oldsmobile and Pontiac
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$101.99

Product Features:

MINI SPOOL GM 7 1/2″ 28 SPLINE

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M86610 race
All steel construction

from

$9.49

Product Features:

KIT SHIM PINION

from

$47.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$551.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$649.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits GM 18.5″ with 30 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$5.99

Replacement Crush Sleeve for GM 7.6″ IRS, 8.5″, 8.6″, 8.75″, 8.875″ & Nissan Titan rear. Approx 0.620″ long.

Product Features:

Crush sleeve for Jeep JK rear, GM 7.6″ IRS, 8.5″ and 8.6″ and Nissan Titan rear
0.620″ tall

from

$214.99

Product Features:

Spider gear kit
Fits GM 8.5″ 30 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$1.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$59.99

Product Features:

Super carrier shim kit for Ford 7.5″, GM 7.5″, 7.625″, 7.6″ IFS, 7.6″ IRS, 7.75″, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and GM 8.5″ front and rear
Interlocking design makes installation much easier

from

$624.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits GM 7.5″ and 7.6″
7.50″ ring gear diameter
27 spline pinion
10 ring gear bolts
4.30 ratio

from

$7.99

Differential Cover B

from

$64.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$153.99

Product Features:

Positraction spring kit
Fits GM 7.5″ and 7.625″ Dura Grip
Includes preload plates

from

$15.99

Standard open side gear thrust washer for 8.5″ GM.

Product Features:

Side gear thrust washer
Fits GM 8.5″

from

$17.99

Manufactured with premium-grade steel, National® taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on