1978 Buick Century Performance Ignition Products

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• 40 ft. Of Conductor Wound Into A Single Foot Of Wire
• For high EMI suppression
• Conductor core features Dupont Kevlar material
• Proprietary compound sleeves for resistance to high heat/abrasion

These ACCEL wire sets are custom tailored for race engines and their builders. The oversize 8.8 mm wire is rated for 600 degrees Fahrenheit and 60kV. Resists heat, chemicals and moisture. High density insulation eliminates arcing. Route over and under headers.

Product Features:

• 150 Ohms Per Foot
• 8.8mm Oversize Silicone Jacket

These ACCEL wire sets are custom tailored for race engines and their builders. The oversize 8.8 mm wire is rated for 600 degrees Fahrenheit and 60kV. Resists heat, chemicals and moisture. High density insulation eliminates arcing. Route over and under headers.

Product Features:

• 300+Race- 8.8mm Black
• For Race Engine Configurations
• Stainless Steel Spark Plug Terminals
• Suppression of EMI/RFI
• 600 Degree Double Silicone Construction
• Spiral Wound Copper/Nickel Alloy
• Fully Reactive Ferrite Material
• 150 Ohms Resistance

These ACCEL wire sets are a true performance upgrade replacement for OE types. Efficient delivery of spark energy for a good price. Silicone boots with blue, black, red and yellow wire, zinc-plated steel terminals. Tinned copper core.

Product Features:

• 7mm And 8mm High Gloss Silicone Jacket
• 450° F Rated Silicone Jacket
• Stainless Steel Plug Terminals
• RFI Suppression For Street Driven Applications

These coils feature advanced bobbin technology, highly specialized silicone magnetic steel cores, along with optimized winding, resistance and turns ratios to delivery 10-15 percent more energy than the OEM coils. Specialized high temperature epoxy resists shock and vibration, while increasing thermal conductivity. These are direct plug replacements for OEM coils. They feature bodies and, or secondary towers molded in ACCEL yellow and feature brass secondary contacts (except direct fire coil on plug applications).

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP Dr-32

Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:

• Direct performance replacement for GM dual connector coil
• 100:1 Turns Ratio
• Lower Primary Resistance Produces High Voltage Output
• Works w/Stock Ignition As Well As MSD Ignitions

These coils feature advanced bobbin technology, highly specialized silicone magnetic steel cores, along with optimized winding, resistance and turns ratios to delivery 10-15 percent more energy than the OEM coils. Specialized high temperature epoxy resist

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

ACCEL offers the only true high-performance. AC Delco style DIS coil. Advanced bobbin technology, specialized magnetic steel core and optimum windings result in higher energy and voltage outputs plus arc duration. Direct bolt and plug in installation.

Product Features:

• 10-15% More Energy
• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Highly Specialized Silicone Magnetic Steel Cores
• Standard Motor Products SMP Dr-39
• MSD 8224

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

• Improved output coil for electronic ignitions
• Works w/Blaster Ignition Or MSD 5/6/7 Series
• Ballast Resistor Required If Used w/Stock Points Ignition
• Alkyd tower w/high dielectric properties lessens carbon tracking

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Product Features:

• Service Part
• Makes Connections Quick And Easy

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

• 8 in. Diameter
• Absolutely the most accurate way to trigger the ignition.
• The non-magnetic pickup cannot be false triggered.
• Powerful magnets are embedded in a billet aluminum trigger wheel.