1977 GMC C25 Performance Engines

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 7.3125 in. Block To Hub Height
• Satin Finish

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Die cut silicone rubber gaskets conform to out-of-flat covers
• Great for on-again/off-again situations
• Not intended for use in emission controlled vehicles.

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

• Fits Chevy engines
• Includes a 1/2 inch NPT threaded hole for by-pass hose
• Includes bolts
• Chrome plated
• Easy to install
• O-ring/gasket not included

Product Features:

• Provides excellent sealing and conformability
• Releases+N747 clean without sticking, if the engine needs to be disassembled
• Perfect companion for Edelbrock cylinder heads and intake manifolds
• Does not include end seals
• Use of a silicone sealant in place of end seal is recommended

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Product Features:

• Great For Street Machines/Street Rods/Muscle Cars
• Two Piece Design
• Individual D-Shaped Runners
• Optimized For Broad Power Range/Large Plenum Area
• Can Be Used For Blow-Through Superchargers
• Fully CNC Machined For A Perfect Fit
• No Exhaust Crossover

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

Product Features:

• HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.
• 279/296 Advertised Duration, 227/241 Duration @ .050″, .498″/.483″ Lift, 107 Lobe Separation
• Valve spring upgrade required

If you are changing your camshaft or replacing the timing set, make sure to replace this seal at the same time! Made from Nitrile rubber.

Product Features:

• Nitrile Rubber And High Density Cork
• Will Not Shrink Or Stick

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

• Black Oxide Coated Grade 8 Steel
• Kit Contains 16 Studs
• Easy To Install
• Heat Treated Steel
• Prevents Stud Flexing
• Black Plated Finish

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Product Features:

• 50-State Street Legal Aluminum Cylinder Head
• Out-of-the-Box Bolt-On Performance
• 70cc Combustion Chambers Improve Performance
• Retain Stock Compression Ratio

The Edelbrock #609019 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

• Cylinder Head Bolts
• Longer-Than-Stock
• High Quality Grade 8 Alloy
• Increase Torque Settings
• Higher Clamp Loads On Gasket

Any gasket can create a seal, but a good gasket can do it with reduced clamping force and for a long period of time. Edelbrock gaskets are manufactured from extremely high-quality materials and are specifically designed to fit Edelbrock intakes and cylinder heads, so there’s no chance that they will interfere with component operation.

Product Features:

• 10-Pack of 7201 Intake Gasket Sets

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Silicone beading on both sides of each gasket
• Complete with manifold end seals and distributor gasket
• For OE replacement, high performance street, drag race and oval track use
• Creates Tight Leak proof Seal

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer
• Washer Between Turbine and Cover

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Manufactured from high-density cork and rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement and high performance street.

Product Features:

• One-piece design
• Eliminates potential leaks
• Prevents over tightening
• Prevents torque loss