1976 Pontiac Firebird Performance Exhaust Products
More 1976 Pontiac Firebird Performance Exhaust Products
Find your specific 1976 Pontiac Firebird original or aftermarket Performance Exhaust Products below. Order your parts online and have delivered to your home or pick up in-store at Advance Auto.
Essential 1976 Pontiac Firebird Performance Exhaust Products
Flowmaster Inc. – Super 44 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942448)
from
$113.99
Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four-inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – 80 Series Muffler, 3in Offset Inlet 2.5in Dual Offset Outlet, Non-Reversible, Aggressive Sound (Part No.43083)
from
$165.99
The 80 series is a cross-flow design for applications where the muffler is mounted transversely behind the rear end. Delivering an aggressive muscle car sound both inside and outside the vehicle, this is an excellent replacement for Camaros & Firebirds with transverse mufflers. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942443)
from
$143.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Hooker Headers – Aero Chamber Muffler (Part No.21729HKR)
from
$215.99
Aero Chamber Muffler
Flowtech – Terminator Muffler, 2.5in Offset Inlet 2.5in Dual Offset Outlet, Non-Reversible, Moderate Sound (Part No.50162FLT)
from
$151.99Product Features:
- Aluminized Steel Construction
- 3in. Inner Pass Tubes
- Reduce Backpressure
- Increase Horsepower
- No Glass To Burn Or Blow Out
- Will Flow In Either Direction
- Welded For Strength/Durability
Flowmaster Inc. – 40 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.42543)
from
$99.99
The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – 40 Series Muffler, 3in Offset Inlet 3in Offset Outlet, 13in long, Non-Reversible, Aggressive Sound (Part No.43043)
from
$99.99
The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More
Flowmaster Inc. – 80 Series Muffler, 2.5in Offset Inlet 2.5in Dual Offset Outlet, Non-Reversible, Aggressive Sound (Part No.842583)
from
$175.99
The 80 series is a cross-flow design for applications where the muffler is mounted transversely behind the rear end. Delivering an aggressive muscle car sound both inside and outside the vehicle, this is an excellent replacement for Camaros and Firebirds with transverse mufflers. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More
Hooker Headers – Competition Header (Part No.2451-1HKR)
from
$619.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.
Product Features:
See More
Product Features:
- High Performance
- Affordable
- Durable 16 Gauge Material
- Welds Easier
- Lasts Longer
- Heat Cured
- High Heat Resistant
Flowtech – Ceramic Header (Part No.31150FLT)
from
$499.99Product Features:
- Fuel Economy From The Engine
- Leak Test For Max Performance
- Ceramic Headers
- Rust And Corrosion Resistance
- Mandrel-Formed Power Plenum
- Leakproof O-Ringed Port Seals
- Include All Mounting Hardware
Hooker Headers – Competition Header (Part No.2460-1HKR)
from
$680.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.
Product Features:
See More
Product Features:
- High Performance
- Affordable
- Durable 16 Gauge Material
- Welds Easier
- Lasts Longer
- Heat Cured
- High Heat Resistant
Flowtech – Standard Header (Part No.11170FLT)
from
$280.99Product Features:
- Fuel Economy From The Engine
- Leak Test For Max Performance
- Mandrel-Formed Power Plenum
- Leakproof O-Ringed Port Seals
- Include All Mounting Hardware
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1423)
from
$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Hooker Headers – Super Competition Header Gasket (Part No.10846HKR)
from
$17.79
Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.
Product Features:
See More
Product Features:
- Tear Resistant
- Precisely Cut To Match Header
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1444)
from
$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5901)
from
$31.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Withstands Intense Exhaust Heat
- Graphite-Impregnated Facing
- Steel Expanded Metal Core
- Superior Tensile Strength
- Resists Deteriorating
- Anti-stick Properties
- Easy Removal For Disassembly
Edelbrock – Exhaust Manifold Gasket Set for Pontiac (Part No.7281)
from
$30.99
Product Features:
See More
- Designed To Match Port Openings Of Cylinder Heads
- Excellent Free-Flowing Seal
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1400)
from
$33.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Copper Seal: Exhaust Gasket Set (Part No.7154)
from
$59.19
Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.
Product Features:
See More
Product Features:
- Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
- Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
- .051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
- Provides excellent sealing and durability
- Conforms to and seals minor surface irregularities
- For high performance street, drag race, oval track and turbocharged (extreme heat) applications
- Ideal For Tow Vehicles
- Ideal For Motorhomes
Flowtech – Real-Seal; Header Gasket (Part No.99150AFLT)
from
$85.39Product Features:
- Water/Weather Resistant
- Re-Useable
- Will Not Burn Or Blow Out
- Suitable For Port-Matching
- Made In USA
Mr. Gasket – Copper Seal; Exhaust Gasket Set (Part No.7150)
from
$59.99
Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.
Product Features:
See More
Product Features:
- Will Not Shrink/Deteriorate
- Creates A Tight Leak Proof Seal
- Helps Lower Under hood Temps
- Seals Irregular Surfaces
- Seals Slightly Damaged Surface
- Ideal For Tow Vehicles
- Ideal For Motor Homes
Mr. Gasket – Mls Exhaust Gasket (Part No.4805G)
from
$49.49
Multi-Layered Steel (MLS) exhaust and header collector gaskets are designed for extreme cylinder pressures produced by high horsepower high compression turbo-charged, supercharged and nitrous oxide injected engines. Manufactured from three stainless steel layers, they resist corrosion, will not burn through or push out and maintain maximum fastener torque retention. Stress formed inner and outer layer embossments act like springs that rebound under exhaust flange clamp load, creating force to seal extreme exhaust pressures. Total gasket thickness .075 inch. Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.
Product Features:
See More
Product Features:
- Multi Layer Stainless Steel 3-Layers
- Round Port 1.75″ Diameter
- Will not deteriorate from scrubbing action caused by different expansion rates in aluminum and steel materials.
- Thickness .072″
- Fits GM LS Series Engines 1997-’15
Mr. Gasket – Performance Exhaust Gasket Set for Enhanced Sealing and Durability (Part No.150B)
from
$20.99
Mr. Gasket Performance exhaust gasket material is a heavy duty material, .062 inch thick, consisting of an acrylic binder system to resist high temperature. This material is made for sealing exhaust applications. Provides excellent sealing and durability.
Product Features:
See More
Product Features:
- Manufactured from high-temperature acrylic blend exhaust material
- Provides excellent sealing and durability
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Resists Deteriorating
- Provides Excellent Torque Retention
Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5920)
from
$45.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-temperature steel core/graphite faced exhaust material
- Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
- Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
- Conforms to and seals minor surface irregularities
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Anti-Stick Properties
- Easy Removal For Disassembly
Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5908)
from
$45.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-temperature steel core/graphite faced exhaust material.
- Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
- Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
- Conforms to and seals minor surface irregularities
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Anti-Stick Properties
- Easy Removal For Disassembly
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1448)
from
$34.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Copper Seal; Exhaust Gasket Set (Part No.7151)
from
$60.29
Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.
Product Features:
See More
Product Features:
- Will Not Shrink/Deteriorate
- Creates A Tight Leak Proof Seal
- Helps Lower Under hood Temps
- Seals Irregular Surfaces
- Seals Slightly Damaged Surface
- Ideal For Tow Vehicles
- Ideal For Motor Homes
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1436)
from
$38.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Popular 1976 Pontiac Firebird Performance Exhaust Products Categories
1976 Pontiac Firebird Performance Exhaust Products
Maybe you’re in the middle of a full rebuild of that 1976 Pontiac Firebird. Maybe you just need a couple of Performance Exhaust Products. Either way, Advance Auto Parts has 11 different Performance Exhaust Products in our inventory ranging from $30.99 to $280.99. That means you can find the exact parts or products you need to keep that 1976 Pontiac Firebird running smoothly.
Performance Exhaust Products are only as good as their brand. We stock 6 different brands to make sure you have plenty of trusted parts to choose from for your 1976 Pontiac Firebird. Flowmaster Inc., Mr. Gasket, and Hooker Headers are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!
We know you’ll find the perfect Performance Exhaust Products for your 1976 Pontiac Firebird, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 206 reviews in this category, some of the top rated parts include Standard Header with 3.0 stars.
So if you’re in the market for aftermarket Performance Exhaust Products to keep your 1976 Pontiac Firebird rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!
Performance Exhaust Products Brands To Make Your 1976 Pontiac Firebird Last
Simple repair, complete replacement, or a full rebuild. No matter the job, your 1976 Pontiac Firebird demands trusted brand parts and products to keep it running. Many trusted brands of Performance Exhaust Products make up Advance Auto Parts’ inventory, and all are ready to help make your Firebird the best it can be. Be sure to browse some of our top Performance Exhaust Products brands and parts.
Popular Flowmaster Inc. Performance Exhaust Products
We carry Flowmaster Inc. parts in our stock across Performance Exhaust Mufflers categories, plus more. For a 1976 Pontiac Firebird, our most popular Flowmaster Inc. Performance Exhaust Products include:
from
$99.99
(2)
40 Series Muffler, 3in Offset Inlet 3in Offset Outlet, 13in long, Non-Reversible, Aggressive Sound
Performance Exhaust Mufflers
from
$99.99
(13)
40 Series Muffler, 2.5in Offset Inlet 2.5in Offset Outlet, Non-Reversible, Aggressive Sound
Performance Exhaust Mufflers
FAQs for 1976 Pontiac Firebird Performance Exhaust Products
What are the most purchased Performance Exhaust Products for the 1976 Pontiac Firebird?
Out of 11 Performance Exhaust Products for the 1976 Pontiac Firebird, the most popular in our inventory are:
from
$175.99
This product is not rated
80 Series Muffler, 2.5in Offset Inlet 2.5in Dual Offset Outlet, Non-Reversible, Aggressive Sound
Performance Exhaust Mufflers
What are the top-rated 1976 Pontiac Firebird Performance Exhaust Products?
Top-rated Performance Exhaust Products for your 1976 Pontiac Firebird based on customer reviews/ratings are:
from
$280.99
(1)
Standard Header
“Sold as exact fit, but the passenger side header hits the shifter. This product is not an exact fit! I had to heat up and bend one of the header pipes”
