1976 Mercury Comet Performance Engines

Essential 1976 Mercury Comet Performance Engines

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

289-302 Ford Head Bolt Kit

from

$107.99


Product Features:
  • Highest Quality Head Bolts
  • Cold-Formed/Heat Treated
  • Ensures Molecular Integrity
  • Reduced Diameter Bolt Heads
  • Hardened/Parallel-Ground Washers Included
  • Rated At 170000 psi
  • Manufactured By ARP
See More

Mr. Gasket – Mls Head Gasket (Part No.3175G)

Mls Head Gasket

from

$110.99
Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

Product Features:
  • Gasket bore – 4.030 inch: Compressed thickness – .040 inch
  • Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
  • Optimized sealing embossments seals extreme cylinder pressure
  • Provides excellent stability and reduces cylinder bore distortion.
  • Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
  • Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
  • For high-performance street, drag race and oval track use
See More

Edelbrock – Pushrod Set for Small Block Ford 289-302 (Part No.9632)

Pushrod Set for Small Block Ford 289-302

from

$210.99
Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST

from

$237.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:
  • Cost effective aluminum construction provides superior strength to weight ratio
  • Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
  • Durable design increases valve lift while withstanding the rigors of moderate race use
  • Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
See More

Edelbrock – Water Pump for Small-Block Ford in Polished Finish (Part No.8846)

Water Pump for Small-Block Ford in Polished Finish

from

$381.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Competition Cams – Thumpr 227/241 Hydraulic Roller Cam (Part No.31-600-8)

Thumpr 227/241 Hydraulic Roller Cam

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1963)

Rear Main Seal Gasket

from

$42.49
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Edelbrock – Performer Small-Block Ford 1.90" Cylinder Head Hydraulic Flat Tappet (Part No.60329)

Performer Small-Block Ford 1.90" Cylinder Head Hydraulic Flat Tappet

from

$1035.99
50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:
  • 50-State Street Legal Aluminum Cylinder Head
  • Out-of-the-Box Bolt-On Performance
  • Intake Valves Are For Use w/Stock Pistons
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Performer Series Retainer (Qty 16)

from

$100.99
Product Features:
  • Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Mr. Gasket – Intake Manifold Bolts (Part No.958G)

Intake Manifold Bolts

from

$19.99
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers

Product Features:
  • Hex Head
  • Zinc Plated
  • Ideal For Minimal Space
  • 12-Point Head And Flange
  • Zinc Plated For Protection
See More

Edelbrock – Torker II 302 Intake Manifold Small-Block Ford (Part No.5021)

Torker II 302 Intake Manifold Small-Block Ford

from

$376.99
2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Available in cast or polished.

Product Features:
  • 2500 to 6500 RPM High Performance Street Engines
  • Single-Plane Low-Rise Intake Good for High RPM
  • Ideal for Applications with Limited Hood Clearance
  • For Top-End HP and Adequate Throttle Response
See More

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)

Ultra Seal: Harmonic Balancer Bolt/Washer Kit

from

$38.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:
  • Heat treated black oxide coated Grade 8 alloy steel
  • Thick parallel ground washer provides more accurate, uniform torque
  • Hex Prevents Socket Slippage
  • Accurate And Uniform Torque
  • Black Plated Finish
See More

B & M – Torque Converter, Tork Master 3000 (Part No.50442)

Torque Converter, Tork Master 3000

from

$587.99
A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength. Due to torque converter co

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

B & M – Torque Converter, Tork Master 2400 (Part No.50441)

Torque Converter, Tork Master 2400

from

$450.99
A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength. Due to torque converter co

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79

from

$141.99
Product Features:
  • Non-Rotator Type
  • 1.550 in. Outer Diameter
  • .190 Wire Size
  • Single Coil Spring Type
  • Set of 16
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Ford 289-302 & 351W V8 (Part No.5796)

Complete Sure Seat Valve Spring Kit for Ford 289-302 & 351W V8

from

$186.99
Product Features:
  • Non-Rotator
  • 1.438 in. Outside Diameter
  • 1.024 in. Inside Diameter
  • 1.260 in. Coil Blind
  • Set of 16
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1247)

Lower Intake Manifold Gasket Set: 5 Piece Set

from

$46.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
  • Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
  • Medium riser
  • Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Intake Gasket (Part No.203G)

Intake Gasket

from

$36.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals and distributor gasket where applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Mr. Gasket – Cam Change Gaskets (Part No.4410)

Cam Change Gaskets

from

$63.09
If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:
  • Contains all the gaskets needed to change out your camshaft
  • Fuel Injector O-Ring Not Included
  • Meets Performance Standards
See More

Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5870)

Ultra Seal: Valve Cover Gasket Set

from

$36.49
Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are .187 inch thick.

Product Features:
  • Manufactured from high-density cork /rubber blend gasket material
  • A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
  • Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
  • For OE replacement, high performance street, drag race and oval track
  • .187″ thick
  • Handles Ex Flange Pressure
  • Forms Leak Proof Seal
  • Black Latex Coating
See More

Mr. Gasket – Valve Cover Gasket Set (Part No.276)

Valve Cover Gasket Set

from

$30.19
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Manufactured from high-density cork/rubber blend gasket material
  • Provides excellent sealing and durability
  • For OE replacement, high performance street, drag race and oval track use
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7820)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$67.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
  • For Engine with One-Piece Fuel Pump Eccentric
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1817)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.6683)

Ultra Seal: Oil Pan Gasket

from

$59.19
High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:
  • Steel core provides rigidity, durability and prevents gasket push out
  • Molded rubber coating seals minor irregularities in pan surface
  • One piece design is easier to install and even less prone to leak
  • Direct replacement suitable for all uses – street, racing, heavy duty
  • Include both gasket and new oil pan bolts
  • No Cork Particles
  • Easy Removal For Disassembly
See More

1976 Mercury Comet Performance Engines

Maybe you’re in the middle of a full rebuild of that 1976 Mercury Comet. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 42 different Performance Engines in our inventory ranging from $19.99 to $1,035.99. That means you can find the exact parts or products you need to keep that 1976 Mercury Comet running smoothly.

Performance Engines are only as good as their brand. We stock 5 different brands to make sure you have plenty of trusted parts to choose from for your 1976 Mercury Comet. Mr. Gasket, FEL-PRO Performance, and Edelbrock are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1976 Mercury Comet, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 61 reviews in this category, some of the top rated parts include 289-302 Ford Head Bolt Kit with 2.0 stars and ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST with 1.0 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1976 Mercury Comet rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1976 Mercury Comet Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1976 Mercury Comet demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Comet the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular FEL-PRO Performance Performance Engines

We carry FEL-PRO Performance parts in our stock across Performance Engine Intake Manifold Gaskets and Performance Engine Valve Cover Gasket Sets categories, plus more. For a 1976 Mercury Comet, our most popular FEL-PRO Performance Performance Engines include:
Lower Intake Manifold Gasket Set: 11 Piece Set
from $33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets
Engine Valve Cover Gasket Set
from $46.99
(1)
Engine Valve Cover Gasket Set
Performance Engine Valve Cover Gasket Sets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $51.99
(2)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets

FAQs for 1976 Mercury Comet Performance Engines

What are the most purchased Performance Engines for the 1976 Mercury Comet?

Out of 42 Performance Engines for the 1976 Mercury Comet, the most popular in our inventory are:
Intake Manifold Gasket for 1963-1996 Small-Block Fords
from $28.99
(1)
Intake Manifold Gasket for 1963-1996 Small-Block Fords
Performance Engine Intake Manifold Gaskets
Performer-Link Adjustable True-Roller Timing Chain Set
from $67.99
This product is not rated
Performer-Link Adjustable True-Roller Timing Chain Set
Performance Engine Timing Sets and Components
Ultra Seal: Harmonic Balancer Bolt/Washer Kit
from $38.49
This product is not rated
Ultra Seal: Harmonic Balancer Bolt/Washer Kit
Performance Engine Harmonic Balancers

What are the top-rated 1976 Mercury Comet Performance Engines?

Top-rated Performance Engines for your 1976 Mercury Comet based on customer reviews/ratings are:
289-302 Ford Head Bolt Kit
from $107.99
(7)
289-302 Ford Head Bolt Kit
“Great quality bolts. They include thread locker. Would definitely recommend to anyone replacing their heads.”
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
from $237.99
(1)
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
“These things break very easy. Not a big fan of the soft brass when trying to install them with the screwdriver head they use. Change it hex and it woy”
Sure Seat Valve Springs for Ford 429/460 V8 1969-1987
from $111.99
(1)
Sure Seat Valve Springs for Ford 429/460 V8 1969-1987
“THIS WAS NOT A COMPLETE KIT!ONLY GOT VALVE SPRINGS!!!”