1976 Jeep Cherokee Performance and Racing Products
Find Your Specific 1976 Jeep Cherokee Performance and Racing Products
Below you will find various in-demand Jeep Performance and Racing Products, components and accessories for your 1976 Cherokee. Advance Auto Parts has popular Cherokee parts like Performance Fuel Systems, Performance Exhaust Products, Performance Engines and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Cherokee model years including
2014,
2015,
2016,
2017,
2018,
2019,
2020,
2021,
2022 and more. Select a category of 1976 Jeep Cherokee Performance and Racing Products below and start saving instantly.
Popular 1976 Jeep Cherokee Performance and Racing Products Categories
Essential Performance and Racing Products for 1976 Jeep Cherokees
Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)
from
$407.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Manual Choke Type
- 750 cfm Maximum Flow Rating
B & M – Automatic Shifter, Street Bandit Shifter (Part No.80797)
from
$869.99
The ultimate shifter for automatic transmission equipped street vehicles! The Hi-Tek Street bandit has all the same feature as the above Street Bandit line of shifters, with an interchangeable billet knob design.
Product Features:
See More
Product Features:
- Ideal For High-Tech Pro-Street
- Ideal For High-Tech Street Rods
- Narrow Styled Aluminum Housing
- Includes Neutral Safety Switch
- Includes Backup Light Switch
- Includes Billet Aluminum Knob
- Can Be Used w/Reverse Pattern Valve Body
Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)
from
$149.99
Product Features:
See More
- Non-Rotator Type
- 1.550 in. Outer Diameter
- .190 Wire Size
- Single Coil Spring Type
- Set of 16
Accel – High-Performance Ignition Coil – Direct OE Fit (Part No.140021)
from
$80.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Standard Motor Products SMP Uf-198
- MSD 8228
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1434)
from
$32.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Edelbrock – Water Pump AMC Long Style 1973-Later (Part No.8832)
from
$365.99
Edelbrock #8832 Water Pump AMC long style 1973-later ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pumps
Product Features:
See More
Product Features:
- Standard Impeller Rotation
- 0.625 in. Pilot Shaft
- 0.750 in. Ball/Ball Bearing
- 4.1875 in. Block To Hub Height
- Satin Finish
Mr. Gasket – Thermocap Radiator Cap (Part No.2470B)
from
$55.99
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps prevent coolant injuries
- Fahrenheit and centigrade readings
- Color-coded temperature ranges
- Integrated coolant reclamation valve
- Improves under-hood appearance
- Chromed crown with a colored trim ring
Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)
from
$5.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)
from
$33.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with .530″ guides and 3/8″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
Mallory – Distributor Wiring Harness (Part No.29349)
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$32.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Edelbrock – Performer EGR AMC Intake Manifold (Part No.3731)
from
$509.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Rugged Ridge – Heavy Duty Differential Skid Plate (Part No.16597.35)
from
$114.99
Protect your factory differential cover with these heavy duty skid plates. Designed to fit the contours of your stock differential cover and made of durable 3/16-inch black powdercoated steel, these skid plates will help you slide over obstacles.
Product Features:
See More
Product Features:
- Black Powder Coated
- 3/16 in. Steel
- Use w/ Factory Diff Cover
- Mounting Hardware Included
Rugged Ridge – Skid Plate (Part No.DMC-16597.44)
from
$205.99
Protect your factory differential cover with These heavy-duty skid plates. Designed to fit the contours of your stock differential cover. Constructed of durable 3/16 in. black powder coated steel, these skid plates will help you slide over obstacles and not get hung up. Includes replacement mounting hardware and instructions. Will not fit Aluminum Housing D44A.
Product Features:
See More
Product Features:
- Black Powder Coated
- 3/16 in. Steel
- Use w/Factory Diff Cover
- Mounting Hardware Included
- Jeep Logo
K&N – Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (Part No.HP-2003)
from
$19.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.
Product Features:
See More
Product Features:
- Designed to allow high flow rates and a consistent flow of oil to your engine
- Pleated synthetic-blend filtration media removes most harmful contaminants
- Fast and easy Wrench-Off removal using the welded one-inch hex nut
- High capacity to withstand the service intervals recommended by vehicle manufacturers
- Heavy-duty canister for outstanding durability
- Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
- Designed to operate with all synthetic, conventional, and blended motor oils
- 1-Year Limited Warranty
K&N – Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (Part No.HP-1017)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N’s Limited Warranty.
Product Features:
See More
Product Features:
- Designed to allow high flow rates and a consistent flow of oil to your engine
- Pleated synthetic-blend filtration media removes most harmful contaminants
- Fast and easy Wrench-Off removal using the welded one-inch hex nut
- High capacity to withstand the service intervals recommended by vehicle manufacturers
- Heavy-duty canister for outstanding durability
- Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
- Designed to operate with all synthetic, conventional, and blended motor oils
- Limited Warranty
Product Features:
B & M – Holeshot 2400 (Part No.20412)
from
$562.99
HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
B & M – Holeshot 3000 (Part No.20413)
from
$921.99
HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
B & M – Tork Master 3000 (Part No.20402)
from
$562.99
Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
- Washer Between Turbine and Cover
MSD Ignition – Distributor; 6-cyl. AMC Jeep 232-258; 4.0L (Part No.8516)
from
$665.99
There is a big following of AMC enthusiasts that are cruising a 401 equipped Javelin or trail blazing in a rock crawling Jeep with an inline 6-cylinder! MSD offers two Pro-Billet Distributors to deliver accurate trigger signals and are maintenance-free! This pick-up never requires adjustment and simply plugs right into an MSD Ignition Control. Just above it and under our strong race rotor is an adjustable mechanical advance assembly. The chro-moly weights of this assembly slide on nylon bushings producing smooth movement of the timing. You can easily adjust the curve to match your engine’s requirements with the supplied springs and stop bushings. Each precision CNC-machined billet aluminum housing features a sealed ball-bearing and long sintered bushing for stability at any rpm and increased endurance. An oversized steel shaft receives a QPQ coating to reduce friction and prevent corrosion. Both distributors are supplied with a high quality cap, rotor and gear. There is even a vacuum advance canister for street cruising economy!
Product Features:
See More
Product Features:
- Designed For Street/Performance Use w/Mech or Vacuum Advance
- Must Be Used w/An MSD Ignition Control
- Supplied w/Socket Style Distributor Cap And Rotor
- Nylon pads ensure smooth operation of the advance weights
- Advance weight pins are staked and tig welded to the plate
- Mech. advance assem. can be locked out for crank trigger systems
- Advance plate and weights are fine blanked from chrome moly steel
- QPQ coated for friction reduction
Mallory – Unilite Electronic Ignition Distributor Series 37 (Part No.3760001)
from
$614.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
B & M – Aluminum Braided Dip Stick, Fits TH-400 Transmission (Part No.22166)
from
$127.99
What better way to check you oil level by using one of B&M’s transmission fluid dipsticks? The cap screws into the tube and is O-ring sealed, while the base of the tube has a sealing grommet where it goes into the transmission.
Product Features:
See More
Product Features:
- Automatic Transmission Dip Stick
Upgrade your 1976 Jeep Cherokee with Top-Quality Performance and Racing Products
When it comes to maintaining or upgrading your 1976 Jeep Cherokee, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Jeep or enhancing its overall performance, Performance and Racing Products are key to keeping your Cherokee functioning at its best. At Advance Auto Parts, we offer a wide selection of 58 Performance and Racing Products for the 1976 Jeep Cherokee, designed to meet your needs without breaking the bank.
From
Performance Fuel System
replacements to
Performance Exhaust Products
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1976 Jeep Cherokee at great prices.
Our Performance and Racing Products inventory for this model
ranges from just $5.99 to $972.99, with
an average price of $294.25.
Our 58 Performance and Racing Products in stock come from 11 trusted brands, so you’re sure to find the right part for your 1976 Jeep Cherokee without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1976 Jeep Cherokee, we stock popular OEM and aftermarket Performance and Racing Products from top names
like Edelbrock, Holley, MSD Ignition, and more.
Edelbrock Performance and Racing Products
start at just $394.99 and boast an impressive 4.4 stars average rating from customers.
Holley and MSD Ignition also bring quality to the table, with Performance and Racing Products available starting at $55.99, and at an average 4.2 stars rating.
With 744 customer reviews and counting, our 1976 Jeep Cherokee Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1976 Jeep Cherokee is always ready to roll. We’re committed to providing you with everything you need to keep your Cherokee in top shape, all in one place.
Start shopping confidently below for your 1976 Jeep Cherokee!
Best-Selling Performance Fuel Systems for 1976 Jeep Cherokees
Enhance the driving experience in your Jeep with 9 quality Performance Fuel System components, starting at $394.99.
Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80457S)
from
$509.99
Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)
from
$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Holley – Prem Street Carbs (Avengers) (Part No.0-80770)
from
$716.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Performer Remanufactured Carburetor, 600 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9905)
from
$437.99
The Edelbrock 9905 Remanufactured Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 9905 Remanufactured Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
See More
Holley – Off Road Carbs (Part No.0-90670)
from
$819.99
The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Extreme Off Road Environments
- Single Feed Fuel Inlet For Ease Of Installation
- Optimized Off-Road Calibration That Works Out-Of-The-Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- One Piece Off-Road Vent Tube Eliminates Fuel Spillover
- Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
- Limited Lifetime Warranty Defects In Material/Workmanship
Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)
from
$523.99
The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
- Electric Choke Installed from Factory
- Smooth Secondary Transition
- Includes Only Timed Vacuum Port
- Includes EGR ; Fuel Vapor Outlet
Edelbrock – Thunder AVS Carburetor #1826 650 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.1826)
from
$464.99
New or reconditioned 650cfm. Square-flange. Electric choke without EGR. Primary jet 0.095. Secondary jet 0.098. Metering Rod 0.065 x 0.047. Dual plane intake. Spring loaded needles and seat increase performance. New qwik-tune adjustable secondary air valve. Distinctive black accented hardware. Lightweight ball burnished aluminum. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage.
Product Features:
See More
Product Features:
- Spring Loaded Needles/Seat Increase Performance
- New Qwik-Tune Adjustable Secondary Air Valve
- Distinctive Black Accented Hardware
- Lightweight Ball-Burnished Aluminum
- No Gaskets Below Fuel Level to Prevent Leakage
- Metering Rod/Step Up Springs Can Be Changed Easily
- GM/AMC-Style Throttle Linkage
Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)
from
$407.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Manual Choke Type
- 750 cfm Maximum Flow Rating
Most Popular 1976 Jeep Cherokee Performance Exhaust Products
Customize your Jeep with 1 Performance Exhaust Products products
like Performance Exhaust Manifold Gaskets, all
priced under $32.99.
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1434)
from
$32.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Top Picks for 1976 Jeep Cherokee Performance Engines
Upgrade Jeep Cherokees with top-quality Performance Engines parts, including 33 OEM and aftermarket selections for your 1976 model.
Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)
from
$33.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with .530″ guides and 3/8″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
B & M – Tork Master 3000 (Part No.20402)
from
$562.99
Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
- Washer Between Turbine and Cover
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$32.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)
from
$337.99
Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost
Product Features:
See More
Product Features:
- New Precision Pump Drive Tube
- Pressure Tested
- Fully Balanced
- Needle Thrust Bearing
- New Thrust Washer
Edelbrock – Performer EGR AMC Intake Manifold (Part No.3731)
from
$509.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
B & M – Holeshot 3600 (Part No.20425)
from
$972.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
- Dual Pattern Drive Lugs
- New Turbine Hub
- New Springs/Rollers In Stator
B & M – Holeshot 3000 (Part No.20413)
from
$921.99
HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
Competition Cams – High Energy 218/218 Hydraulic Flat Cam K-Kit for AMC 290-401 (Part No.K10-202-4)
from
$858.99
High Energy 218/218 Hydraulic Flat Cam K-Kit for AMC 290-401
Competition Cams – Thumpr 227/241 Hydraulic Flat Cam and Lifter Kit for AMC 290-401 (Part No.CL10-600-5)
from
$656.99
Thumpr 227/241 Hydraulic Flat Cam and Lifter Kit for AMC 290-401
Competition Cams – High Energy 218/218 Hydraulic Flat Cam and Lifter Kit for AMC 290-401 (Part No.CL10-202-4)
from
$618.99
High Energy 218/218 Hydraulic Flat Cam and Lifter Kit for AMC 290-401
Competition Cams – Magnum 224/224 Hydraulic Flat Cam and Lifter Kit for AMC 290-401 (Part No.CL10-203-4)
from
$598.99
Magnum 224/224 Hydraulic Flat Cam and Lifter Kit for AMC 290-401
B & M – Holeshot 2400 (Part No.20412)
from
$562.99
HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c
Product Features:
See More
Product Features:
- Furnace Brazed Impeller
- Steel Alloy Pump Drive Tube
- Heavy Duty Needle Bearing
- Between Stator and Turbine
- Furnace Brazed Turbine
Competition Cams – Xtreme 4X4 206/214 Hydraulic Flat Cam and Lifter Kit for AMC/Jeep 199-258/4.0L (Part No.CL68-231-4)
from
$559.99
Xtreme 4X4 206/214 Hydraulic Flat Cam and Lifter Kit for AMC/Jeep 199-258/4.0L
Edelbrock – RPM Air-Gap AMC 304/360/401 Intake Manifold (Part No.7531)
from
$530.99
Edelbrock part #7531 RPM Air-Gap AMC intake manifold is designed for 1970-91 304-401 c.i.d. V8 applications. The RPM Air-Gap intake manifold incorporate the same race-winning technology as our Victor Series competition intakes. The air-gap design features
Product Features:
See More
Product Features:
- Based on Performer RPM-Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- Designed for 1500 to 6500 RPM Street-Driven Power
- Dual-Plane High-Rise Intake w/180 deg Firing Order
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Includes Std Oil Fill ; PCV ; A/C Accy Bosses
- Not for Exhaust-Heat Chokes – No Exhaust Crossover
Competition Cams – Xtreme 4X4 210/218 Hydraulic Flat Cam for AMC/Jeep 199-258/4.0L (Part No.68-235-4)
from
$458.99
Xtreme 4X4 210/218 Hydraulic Flat Cam for AMC/Jeep 199-258/4.0L
Competition Cams – Xtreme 4X4 206/214 Hydraulic Flat Cam for AMC/Jeep 199-258/4.0L (Part No.68-231-4)
from
$426.99
Xtreme 4X4 206/214 Hydraulic Flat Cam for AMC/Jeep 199-258/4.0L
Competition Cams – Xtreme 4X4 218/226 Hydraulic Flat Cam for AMC/Jeep 199-258/4.0L (Part No.68-239-4)
from
$426.99
Xtreme 4X4 218/226 Hydraulic Flat Cam for AMC/Jeep 199-258/4.0L
Edelbrock – Water Pump AMC Long Style 1973-Later (Part No.8832)
from
$365.99
Edelbrock #8832 Water Pump AMC long style 1973-later ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pumps
Product Features:
See More
Product Features:
- Standard Impeller Rotation
- 0.625 in. Pilot Shaft
- 0.750 in. Ball/Ball Bearing
- 4.1875 in. Block To Hub Height
- Satin Finish
Competition Cams – Hi-Tech 7.950" Long, .080" Wall, 5/16" Diameter Pushrod Set (Part No.7994-16)
from
$281.99
Hi-Tech 7.950" Long, .080" Wall, 5/16" Diameter Pushrod Set
Competition Cams – RKRS AMC PED (Part No.1210-16)
from
$225.99
RKRS AMC PED
Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)
from
$149.99
Product Features:
See More
- Non-Rotator Type
- 1.550 in. Outer Diameter
- .190 Wire Size
- Single Coil Spring Type
- Set of 16
Competition Cams – Engine Valve Spring Kit (Part No.940-16)
from
$111.99
Engine Valve Spring Kit
Competition Cams – 7 Degree Steel Retainer Set of 16 for 3/8" Valve with 1.437"-1.500" Spring (Part No.744-16)
from
$80.99
7 Degree Steel Retainer Set of 16 for 3/8" Valve with 1.437"-1.500" Spring
Competition Cams – Set of 16 Hardened Lash Caps with 3/8" Valve Stem, .190" Head Height (Part No.622-16)
from
$50.99
Set of 16 Hardened Lash Caps with 3/8" Valve Stem, .190" Head Height
In-Demand Performance Oil Filters for 1976 Jeep Cherokees
Select from 1 premium Performance Oil Filters parts for your 1976 Jeep Cherokee.
K&N – Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (Part No.HP-2003)
from
$19.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.
Product Features:
See More
Product Features:
- Designed to allow high flow rates and a consistent flow of oil to your engine
- Pleated synthetic-blend filtration media removes most harmful contaminants
- Fast and easy Wrench-Off removal using the welded one-inch hex nut
- High capacity to withstand the service intervals recommended by vehicle manufacturers
- Heavy-duty canister for outstanding durability
- Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
- Designed to operate with all synthetic, conventional, and blended motor oils
- 1-Year Limited Warranty
Most Sold 1976 Jeep Cherokee Performance Distributors
Explore our best-selling Jeep parts for the 1976 Cherokee among 2 OEM and aftermarket options starting from $614.99.
MSD Ignition – Distributor; 6-cyl. AMC Jeep 232-258; 4.0L (Part No.8516)
from
$665.99
There is a big following of AMC enthusiasts that are cruising a 401 equipped Javelin or trail blazing in a rock crawling Jeep with an inline 6-cylinder! MSD offers two Pro-Billet Distributors to deliver accurate trigger signals and are maintenance-free! This pick-up never requires adjustment and simply plugs right into an MSD Ignition Control. Just above it and under our strong race rotor is an adjustable mechanical advance assembly. The chro-moly weights of this assembly slide on nylon bushings producing smooth movement of the timing. You can easily adjust the curve to match your engine’s requirements with the supplied springs and stop bushings. Each precision CNC-machined billet aluminum housing features a sealed ball-bearing and long sintered bushing for stability at any rpm and increased endurance. An oversized steel shaft receives a QPQ coating to reduce friction and prevent corrosion. Both distributors are supplied with a high quality cap, rotor and gear. There is even a vacuum advance canister for street cruising economy!
Product Features:
See More
Product Features:
- Designed For Street/Performance Use w/Mech or Vacuum Advance
- Must Be Used w/An MSD Ignition Control
- Supplied w/Socket Style Distributor Cap And Rotor
- Nylon pads ensure smooth operation of the advance weights
- Advance weight pins are staked and tig welded to the plate
- Mech. advance assem. can be locked out for crank trigger systems
- Advance plate and weights are fine blanked from chrome moly steel
- QPQ coated for friction reduction
Mallory – Unilite Electronic Ignition Distributor Series 37 (Part No.3760001)
from
$614.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
Top-Rated Performance and Racing Products Brands For Your 1976 Jeep Cherokee
Shop for the best-rated brands offering Performance and Racing Products and other products for your 1976 Jeep Cherokees. Below you’ll find some of our best rated Performance and Racing Products from Edelbrock, Holley, and MSD Ignition, and more. Performance and Racing Products from these brands that fit a 1976 Cherokee start at just $55.99 and are rated as high as 4.4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.
Popular Edelbrock 1976 Jeep Cherokee Performance and Racing Products
When it comes to maintaining or upgrading your 1976 Jeep Cherokee, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Edelbrock ticks all of those boxes. We offer a wide selection of Edelbrock Performance and Racing Products, specifically designed for the 1976 Jeep Cherokee. With over 2 Edelbrock brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $394.99, with an average price of just $416.49. Plus, with over 11 customer reviews and an average rating of 4.4 stars, you can trust that our Edelbrock Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$437.99
(1)
Performer Remanufactured Carburetor, 600 CFM With Manual Choke, Satin Finish (Non-EGR)
“works good when you have all the parts for it after putting the extra parts on i had to modify them so the tranny kickdown and throttle lever did not ”
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!”
Popular Holley 1976 Jeep Cherokee Performance and Racing Products
Holley auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1976 Jeep Cherokee owner should feel confident when installing genuine Holley parts in their vehicle. To ensure the best fit and performance for your 1976 Cherokee, Advance Auto Parts carries a full inventory of 3 Holley Performance and Racing Products. Plus you will be keeping your Jeep in peak condition while saving money because prices on these Holley Performance and Racing Products range from $509.99 to $716.99, plus, with more than 53 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.
from
$509.99
(45)
Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny
“very easy to install…replaced older carb this one is fresh and runs smooth … needed to do minor ajustment .. but nothing anyone couldn’t do …”
from
$699.99
(6)
Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny
“great carb”
FAQs for 1976 Jeep Cherokee Performance and Racing Products
Which Performance and Racing Products are best-sellers for 1976 Jeep Cherokees?
Out of 58 Performance and Racing Products that fit 1976 Jeep Cherokees, the following parts are the top sellers:
- Premium Oil Filter: Ideal for Synthetic, Conventional & Blended Oil, Protects Your Engine (6120011) – $19.99
- Tie Rod Dust Boot (17360821) – $5.99
- Tie Rod Dust Boot (17360833) – $5.99
What’s the price range for 1976 Jeep Cherokee Performance and Racing Products?
Performance and Racing Product prices for the 1976 Jeep Cherokee start at $5.99 and go up to $972.99 for the most premium parts.
What’s the average price of a Performance and Racing Product for a 1976 Jeep Cherokee?
The average price for Performance and Racing Products for the 1976 Jeep Cherokee is $294.25. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Performance and Racing Products for other Jeep Cherokee model years?
What are the cheapest Performance and Racing Products for my 1976 Jeep Cherokee?
The cheapest 1976 Jeep Cherokee Performance and Racing Products we carry in stock are:
- Tie Rod Dust Boot (17360821) – $5.99
- Tie Rod Dust Boot (17360833) – $5.99
- Tie Rod Dust Boot (22906873) – $6.29
- High Energy 7.794" Long, 5/16" Diameter Pushrod (50289688) – $7.99
- Hardened Lash Cap with 3/8" Valve Stem, .190" Head Height (50289460) – $8.99
What are the top-rated Performance and Racing Products that fit the 1976 Jeep Cherokee?
Out of 744 reviews by customers, our 1976 Jeep Cherokee Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1976 Jeep Cherokee and their top-rated products:
- Performance Radiators
- Thermocap Radiator Cap (6900022) – $53.99
- Performance Oil Filters
- Thermocap Radiator Cap (6900022) – $53.99
What types of Performance and Racing Products do you sell for my 1976 Jeep Cherokee?
As of 3/1/26, these are some of the most in-demand types of Performance and Racing Products for a 1976 Jeep Cherokee:
Can I get help with 1976 Jeep Cherokee Performance and Racing Product orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Jeep Performance and Racing Products and more.
What is your return policy for Jeep Cherokee Performance and Racing Products?
Advance Auto Parts keeps returns simple. For new Jeep Cherokee Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
