1976 Ford F-100 Pickup Differentials

Product Features:

• Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

Product Features:

• Brand may vary by location

Product Features:

• Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
• 0.030″ thick

Differential

Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 60
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

• Pinion nut for Ford 7.5″, 8″ and 9″
• 3/4″ x 20 thread
• 1 1/6″ socket

Product Features:

• Fits Ford 9″ with 28 spline pinion
• Larger inner pinion bearing reduces gear deflection under high load
• Races installed
• Nodular iron

Yukon positraction internals for Dana 44 Dura Grip posi, 30 spline. Does not include clutches. Does NOT fit Trac Loc or Powr Lok. Fits Dura Grip ONLY.

Product Features:

• Spider gear kit
• Fits Dana Spicer 44 with Dura Grip positraction
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• Oil baffle for Dana Spicer 44

Yukon replacement standard open carrier case for Dana 44, 3.92 & up, 2-3/8″ tall.

Product Features:

• Standard open carrier case
• Fits Dana Spicer 44 with 30 spline axles
• 3.92 and up ratio only
• Does not include spider gears

Product Features:

• Nodular iron for added strength
• Thick design
• Durable powder coat finish
• Magnetic drain plug
• Made in USA
• High strength stainless steel fasteners

Product Features:

• NODULAR HOUSING 9″ FORD 3.25″ BORE

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

• Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
• 3/8″ x 24 thread

Yukon Performance steel spool for 9″ Ford with 35 spline axles. Spool uses 1.785″ journal bearings. fits 2.8″ and 3.0″ cases. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 35 spline axles
• Small bearing journal to fit 2.968″ and 3.062″ dropouts
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 30 spline axles
• 4.10 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

9″ Ford 2 piece solid preload pinion spacer, Daytona or standard.

Product Features:

• Crush sleeve eliminator kit for Ford 9″ with 28 spline pinion

Product Features:

• Trac Loc spring for Ford 8″ and 9″

Yukon standard open spider gear kit for 9″ Ford with 31 spline axles and 4-pinion design. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 9″ open differential with 31 spline axles
• Includes two side gears, four pinion gears, cross pin shaft, roll pins and spider gear thrust washers.

Standard open and TracLoc cross pin block for 9″ Ford.

Product Features:

• Cross pin block
• Fits Ford 9″

Axle shaft damaged or bearings worn out: This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Product Features:
• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

• Pilot bearing
• Fits Ford 9″
• 0.656″ thick

Product Features:

• Pinion depth shims for Dana Spicer 60 and 70U

Trac Loc clutch guide for 9″ Ford.

Product Features:

• Clutch guide
• Fits Ford 8″ and 9″

Product Features:

• DANA-60 R/P 3.73 STD MG (USES PRE-LOAD SHIMS)

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion support o-ring
• Fits Ford 9″

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Fine thread pinion support bolt (aftermarket aluminum only) for 9″ Ford.

Product Features:

• Pinion support bolt for Ford 9″
• 3/8″ x 24 thread
• 1.5″ long