from

$279.99

Radiator Dominator

from

$668.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$538.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

Absolutely The Most Accurate Way To Trigger The Ignition
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.
Incl. brackets/mounting hardware to fit a variety of engines

from

$879.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$397.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$102.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$105.99

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$1093.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$20.29

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$81.99

The Edelbrock #4491 Signature Series Valve Covers are designed for Chrysler 361-383-400-413-426-440 V8 ’58-79 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:

Big Block Chrysler 383-440
Short
Chrome Steel
Set Of Two
Rubber Grommets For Breather

from

$38.49

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Has A Steel Core With Graphite Facing
Graphite Facing Has Excellent Thermo-conductivity
Coated With High Temp Silicone For Sealing
Will Not (brindle ) Or Indent Aluminum Heads

from

$2198.99

The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur

Product Features:

Complete Pair For Hydraulic Flat Tappet
84cc Combustion Chamber Volume
210cc Intake/70cc Exhaust Runner Volume
2.14 in. Intake/1.81 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$23.79

Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1964 and later Chrysler V8 engines
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$52.99

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

Gains Both Performance and Longevity
Will Handle Any and All Torque
Out Lasts Rubber

from

$269.99

The B&M Unimatic is an ideal replacement for column shift vehicles, includes neutral safety switch, 5 foot cable and a boot and plate.

Product Features:

Ideal As Column Shift Replacement
Includes Neutral Safety Switch
Includes Black T-Handle
Backup Light Not Available
Includes 5 ft. Cable and Hardware
Includes Boot and Plate

from

$175.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

Bolt-on Performance
Custom Fit For Make And Model Listed
Wires Are Pre-Cut To Exact Specifications
Conductor core features DuPont Kevlar material for increased tensile strength
Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

from

$450.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$394.99

The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$165.99

This Spectre Oil Pan was designed for the big block Chrysler/Dodge/Plymouth 383, 400, 413, 426, & 440 engines. This triple chrome plated oil pan is made to replace the oem oil pan.

Product Features:

Triple chrome-plated
Steel construction
Stock capacity
Made from high quality material

from

$759.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.O.D. Dia. 1 I.D. Dia. 2 Damper Seat Load Open Load Coil Bind Rate (Lbs./In.) Titanium Retainer Steel Retainer Cup Seat Shims 1.524 1.110 Y 122 @ 1.900 309 @ 1.400 1.200 373 721, 732 1732, 741 4779* 4757

Product Features:

Seat pressure: 122 lbs. @ 1.900″, Open Pressure: 309 lbs. @ 1.400″
O.D.: 1.524″, I.D.: 1.110″
Single valve springs with damper

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$97.99

This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:

Relocate oil filter to an easy access location

from

$46.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$18.99

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

7 1¿4″ diameter
7 1┐4″ diameter
383 thru 440 cu. in.
Increased Performance
Set Valve Lash At Proper Time

from

$31.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features: