Name: Performer Series Retainer (Qty 16)
Brand: Edelbrock
SKU: 9721
Price: 95.99 USD

from

$95.99

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$189.99

Product Features:

Case-Hardened Tubing
Welded Ends
5/16 in. Diameter
Use with or without Hardened Steel Guideplates

from

$30.99

Edelbrock part #7208 Intake Gaskets for 1965-1990, Mark IV 396-402-427-454-555, Rectangular Port 6 Bolt Flange with no crossover allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, an

Product Features:

1.82″x2.46″
Rectangular Port Style
.060″ Thick
Two Piece Configuration
Composite Material

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$1014.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
70cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$42.49

With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:

Advance the cam for increased torque and horsepower
Tune your powerband for more end torque or increase top end horsepower
Includes (4) offset bushings and (1) 0 degree bushing
Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
Increase Top-End Horsepower

from

$41.99

Product Features:

Replacement Gasket Set For PN[4242]

from

$58.99

Chrome water neck with a swivel top allows you to place your coolant hose where you want it to be, not just where the neck allows. Precision die cast for better fitment, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Chrome Plated Aluminum
O-ring To Prevent Leaks
Swivels For Hard To Fit Applications
Comes With Allen Head Bolts

from

$17.79

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$26.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$438.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM street-driven power. Dual-plane high-rise intake with 180 degree firing order. Produces incredible top-end horsepower. Retains good throttle response and acceleration. Larger plenum and runners maximize other upgrades. Edelbrock total power package maximizes gains. Available in cast, polished or endurashine finish.

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed for 1500 to 6500 RPM Street-Driven Power
Dual-Plane High-Rise Intake w/180 deg Firing Order
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock Total Power Package Maximizes Gains

from

$215.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$213.99

These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:

Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
For applications with less than 350 lbs. of open spring pressure
Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
Ultimate street roller rocker arm designed for serious performance enthusiasts

from

$73.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$665.99

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

3400-3800 RPM
Small And Big Blocks
Serious Performance
Furnace Brazed
Fully Balanced

from

$499.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$43.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$334.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$1322.99

BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:

Cam and lifter kit for Big Block Chevy engines
CL-Kit includes cam, lifters, assembly lube, instructions and decals
HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$75.99

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

Chrome plated
Grade 8
12-point head
AN washers with no exposed shoulder for a professional appearance

from

$64.99

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 3.870 inch, Compressed thickness 0.028 inch

Product Features:

Five layer (graphite core/perforated steel outer layers) composite construction
Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
Provides excellent stability, compressibility and high temperature endurance
Coated with high temperature silicone to ensure sealing of engine fluids
Will not brinell (indent) aluminum cylinder heads
For high performance street, drag race and oval track use
Compatible w/High Octane Fuel
Compatible With Exotic Fuel

from

$39.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$542.99

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

Product Features:

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.
279/296 Advertised Duration, 227/241 Duration @ .050″, .498″/.483″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$258.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

1976 Chevrolet G20 Performance Engines

More 1976 Chevrolet G20 Performance Engines

Essential 1976 Chevrolet G20 Performance Engines

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9630)

Edelbrock – Intake Manifold Gasket for 1965-1990, Mark IV B/B Chevy, Rec Port (Part No.7208)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

Edelbrock – RPM Small-Block Chevy Cylinder Head SBC 70cc Hydraulic Flat Tappet Cam (Part No.60759)

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Edelbrock – Replacement Timing Cover Gasket #4243 For SB Chevy, Fits 2-Piece Part #4242 (Part No.4243)

Mr. Gasket – Water Neck (Part No.9141G)

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1803)

Edelbrock – RPM Air-Gap Big Block Chevy 2-O Intake Manifold (Part No.7561)

Weiand – Action Plus Water Pumps (Part No.9208P)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Competition Cams – MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST (Part No.1412-16)

Mr. Gasket – Ultra Seal: Cylinder Head Bolts (Part No.941G)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1603)

B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)

B & M – Tork Master 3000 (Part No.20402)

Edelbrock – Sure Seat Valve Springs for Chevy 4.3L 90 Deg V6 200, 229, 262 (Part No.5813)

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

Edelbrock – Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet (Part No.2103)

Competition Cams – Thumpr 243/257 Hydraulic Flat Cam and Lifter Kit for Chevrolet Big Block 396-454 (Part No.CL11-602-4)

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5780G)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)

Competition Cams – Thumpr 227/241 Hydraulic Flat Cam (Part No.11-600-4)

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

Popular 1976 Chevrolet G20 Performance Engines Categories

1976 Chevrolet G20 Performance Engines

Performance Engines Brands To Make Your 1976 Chevrolet G20 Last

Popular B & M Performance Engines

Top 1976 Chevrolet G20 Performance Engines from Mr. Gasket

FAQs for 1976 Chevrolet G20 Performance Engines

What are the most purchased Performance Engines for the 1976 Chevrolet G20?

What are the top-rated 1976 Chevrolet G20 Performance Engines?

More Popular Parts for All Makes