1975 Ford LTD Performance Engines

Holley products have been the undisputed leader in fuel systems for over 100 years. Holley carburetors power every NASCAR Sprint Cup team and every NHRA Pro-Stock champion. Holley’s products include performance fuel pumps, fuel injection, intake manifolds, cylinder heads & engine dress-up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies, Hooker Headers, Flowtech Headers, NOS, Weiand, or Earl’s, Holley products can give you the edge you need over the competition.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Inside tang-to-taper relationship held tightly for repeatable valve spring installed heights

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

This B&M Holeshot 2400 fits 1966-91 Ford C6 transmissions with 1.848-inch crank pilot and a 11.4-inch bolt circle. The Holeshot converters are an excellent choice for vehicles with engine modifications, particularly big cams that tend to reduce low end power and torque. The higher stall speed of this converter will launch the car in a higher rpm range where more torque is readily available, resulting in quicker acceleration. Holeshot converters feature furnace brazed impeller fins and turbine, new precision alloy impeller hub and new heavy duty needle bearings. Other features include fully balanced and pressure tested by expert technicians. If your vehicle is equipped with a plate type nitrous system or supercharger, please refer to the Nitrous Holeshot line of converters. Notes: Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. This converter is Not recommended for supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product.

It’s easy to overlook the small details. For engine builders focused on the larger components like camshafts, cylinder heads and pistons, small parts are often forgotten until the final stages of engine assembly. COMP Cams Engine Finishing Kits include those often missing parts like woodruff keys, cylinder head alignment dowels, cam bolts, cam eccentrics and timing cover and oil pump dowel pins that are so crucial to properly assembling your engine.

Edelbrock Ford 429-460 Head Bolt Kit, 8566.

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

“Edelbrock Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02″”, 60399. ”

“Competition Cams High Energy 8.616″” Long, 5/16″” Diameter Pushrod Set, 7844-16. ”

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

The Edelbrock No: 7365 head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit and sealing properties when used with Edelbrock aluminum cylinder heads. Edelbrock head gaskets are manufactured from high-density materials and feature a superior design that performs under pressure and provides a long-lasting seal, without re-torqueing.

Kormetal gasket used between the SysteMax II Ford 5.0L upper and lower manifolds.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Precision die-cast, these water necks are first polished to a high luster, then chrome plated. Comes with gasket and mounting bolts.

“These Magnum Roller Rocker Arms for Ford V8 289-351W (Rail Type) 1968-89 applications are the ultimate street rocker. With a 3/8″” stud diameter and 1.6 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed from 8620 chromemoly steel, which is a superior material that will not flex and assures maximum lift. Their roller tip reduces friction, while stiff design and superior ratio accuracy yield more effective valve lift. With a 15 to 30 horsepower increase over other rocker arms, Magnum Roller Rockers are perfect for performance applications with less than 350 lbs. open spring pressure. Don’t accept inferior products or cheap knock-offs, look for the COMP Cams logo stamped into the underside of every Magnum Rocker.”

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Edelbrock part No: 7811 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Edelbrock part No: 7814 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It is a direct replacement for a factory one-piece rubber main seal. It’s also injection molded for a precise fit.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Competition Cams Magnum Double Row Timing Set for ’69-’84 Ford 351W, 2135.

Competition Cams Magnum Double Row Timing Set for ’65-’88 Ford 255, 289, 302 and Boss 302, 2120.