1975 Ford E-350 Econoline Differentials

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 80 with 4.125″ O.D. pinion bearing
• Included are a pinion seal, complete shim kit, marking compound and brush.

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 30 spline axles
• 4.10 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
• For Trac Loc positraction applications only

Cross pin bolt with 5/16 x 18 thread for 10.25″ Ford.

Product Features:

• Cross pin bolt for Ford 9.75″ and 10.25″ with c-clip axles
• 5/16″ x 18 thread

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

• Cross pin shaft
• Fits Dana Spicer 60 and 70
• Powr Lok positraction only

Product Features:

• MINI-INSTLTN KIT-DANA 70

Yukon 1541H alloy, 8 lug, right hand replacement rear axle for ’95-’10 Semi Float Dana 60, Ford E Series Vans with a length of 31.86″ inches and 35 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a semi float axle.

Product Features:

• 35 spline
• 8 lug
• 31.41″ long
• Fits Dana Spicer 60 in 1995-2002 Ford E250
• Right hand side
• Semi-float axle

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction

This kit uses Koyo bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. USA Standard Gear does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Dana Spicer 70U
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, pinion nut, oil baffles and slingers, marking compound and brush.

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 60

Product Features:

• Pinion depth shims for Dana Spicer 60 and 70U

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 80 with 4.375″ O.D. pinion bearing
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON, GM DEXRON-II and DEXRON-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III, Toyota/Lexus Type T, T-III and T-IV, Honda/Acura ATF-Z1 (except in CVTs), Mercedes Benz NAG1, Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Yukon replacement standard open carrier case for Dana 80, 4.10 & up (NOT ABS) 35 & 37 spline.

Product Features:

• Standard open carrier case
• Does not include spider gears
• Fits Dana Spicer 80 with 35 or 37 spline axles
• 4.10 and up ratio only
• Not compatible with ABS applications

M802048 set-up bearing (one bearing). No return.

Product Features:

• Set up bearing
• Fits M802048 pinion bearing
• Easily slips on and off pinion journal to allow for easier pinion depth adjustment

Product Features:

• Nodular iron for added strength
• Thick design
• Durable powder coat finish
• Magnetic drain plug
• Made in USA
• High strength stainless steel fasteners

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

55P Chevy Passenger Drop Out gasket.

Product Features:

• Side gear thrust washer
• Fits Ford 10.25″

Product Features:

• Oil baffle
• Fits Dana Spicer 70 and 70HD

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Ford 7.5″, 8.8″, 9″ and 10.25″

Yukon replacement standard open spider gear kit for Dana 60 with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 60 open differential with 30 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

• Seal housing for Dana Spicer 60
• Includes o-rings

10.25″ Ford carrier Supershims.

Product Features:

• Super carrier shim kit for Ford 10.25″ and 10.5″
• Interlocking design makes installation much easier