1975 Ford Custom 500 Air Intakes
Find Your Specific 1975 Ford Custom 500 Air Intakes
Below you will find various in-demand Ford Air Intakes, components and accessories for your 1975 Custom 500. Advance Auto Parts has popular Custom 500 parts like Carburetor Kits, Carburetor Parts, Throttle Bodies & Carb Parts and more. You’ll also find aftermarket and OEM Air Intakes for other Custom 500 model years including
1968,
1969,
1970,
1971,
1972,
1973,
1974,
1976,
1977 and more. Select a category of 1975 Ford Custom 500 Air Intakes below and start saving instantly.
Popular 1975 Ford Custom 500 Air Intakes Categories
Essential Air Intakes for 1975 Ford Custom 500s
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Edelbrock – Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1223)
from
$50.99
Product Features:
See More
- Edelbrock triple chrome-plated round air cleaner #1223 work with all popular 5-1/8″ diameter Carburetors (Performer Series, Thunder Series AVS, Holley, Thermo-Quad, Quadra jet and Carter AFB).
- The 10″ and 14″ models have knock-outs in the air cleaner base for use with Edelbrock crank case ventilation adapter #1205 (sold separately).
- #1208, #1209 and #1221 fit all Edelbrock Carburetors.
- Heights of air cleaners are in parentheses, measured from the gasket flange to the top of the supplied retaining nut.
- Dimensions are accurate within 1/8″.
Holley – Prem Street Carbs (Avengers) (Part No.0-81670)
from
$687.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Manual Choke For Precise Cold Start Control
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)
from
$474.99
The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Holley – Professional Race Carburetor: 1050 CFM, No Choke, 4 Barrel, 4500 Bore, Dual Inlet, Shiny (Part No.0-80903RD)
from
$1700.99
The Gen 3 utilizes high capacity fuel bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, 12 hole billet booster inserts, fully tunable billet metering blocks, adjustable external linkage, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws Each calibration has been dyno and track tested to deliver proven performance!
Product Features:
See More
Product Features:
- All Aluminum Construction Saves 3.8 lbs. Over Original Models
- 28% Weight Savings
- Calibrations For Todays Larger Race Engines and New Fuels
- Fully Machined From Venturi Throat To Throttle Bore
- Integrated Idle Bypass Valve Allows For Adjustment Of Idle
- 12 Hole Billet Booster Superior Atomization/Throttle Response
- Metering Blocks Feature Improved True Gasket Sealing
- Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Windows On Sides Of Bowl For Fuel Level Adjustments
- Drain Plug On Bowl Provides Easy Access To Empty Bowl
- Contoured Hex Head Squirter Screws For Streamlined Airflow
Edelbrock – RPM Air-Gap Small Block Ford 302 Black Intake Manifold (Part No.75213)
from
$605.99
Edelbrock part #75213 RPM Air-Gap intake manifold is designed for street 289 302-347 c.i.d. Ford V8’s. The RPM Air-Gap incorporates the same race-winning technology that’s been used on our Victor Series competition intakes for decades. The Air-Gap design
Product Features:
See More
Product Features:
- 1500-6500 RPM Range
- Dual Plane Type-4150 Style Flange
- 4.3 in. Front Height, 4.9 in. Center Height, 5.5 in. Rear Height
- Black Powder Coated Finish
- Made In The USA
Edelbrock – RPM Air-Gap #7521 Intake Manifold for Small-Block Ford 302-331-347 V8 (Part No.7521)
from
$454.99
Edelbrock Part #7521 RPM Air-Gap intake manifold is designed for the small-block 302 CID Ford V8 or 331-347 stroker applications. The RPM Air-Gap incorporates the same race-winning technology that?s been used on our Victor Series competition intakes and i
Product Features:
See More
Product Features:
- RPM Air-Gap for 302-331-347 Small-Block Ford V8
- Air-Gap design features an open air space under the plenum
- Separates fuel and air from engine heat
- Larger runners over standard 7121 manifold
- Includes nitrous bosses
Edelbrock – Performer 289 Intake Manifold for Small-Block Ford (Part No.2121)
from
$314.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal
- Available in Multiple Finishes
Felpro – Carburetor Mounting Gasket (Part No.60716)
from
$7.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Fuel Injection Throttle Body Mounting Gasket (Part No.ES 70582)
from
$15.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Felpro – Carburetor Mounting Gasket (Part No.60101)
from
$10.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Carburetor Mounting Gasket (Part No.60332)
from
$3.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Victor Reinz – Carburetor Mounting Gasket (Part No.71-13696-00)
from
$16.99
Product Features:
See More
- Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
- Dana engineering-approved for fit, form and function
- Meets or exceeds OE specifications
Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 90361)
from
$26.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES – Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE – Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED – Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Edelbrock – Intake Manifold Gasket for 1963-1996 Small-Block Fords (Part No.72208)
from
$174.99
Available in different sizes for many different vehicle models/years. Clean positive seal. Embossed silicone bead surrounding the port. Matched to manifolds and cylinder heads. In the early days of the automotive performance industry, you either ran what
Product Features:
See More
Product Features:
- Clean positive seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
- Fits 1963-96 289/302/351W Engines
- 10-Pack Of Gaskets
Mr. Gasket – Intake Gasket (Part No.222)
from
$45.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Die-cut for an excellent fit
- Can be trimmed if necessary for modified port applications
- Complete with manifold end seals
- For OE replacement, high performance street, drag race and oval track use
Mr. Gasket – Intake Gasket (Part No.211)
from
$42.99
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Die-cut for an excellent fit
- Can be trimmed if necessary for modified port applications
- Complete with manifold end seals
- For OE replacement, high performance street, drag race and oval track use
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Felpro – Air Cleaner Mounting Gasket (Part No.60032)
from
$3.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1793)
from
$46.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1764)
from
$38.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1784)
from
$22.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1822)
from
$37.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1792)
from
$28.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1768)
from
$25.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1802)
from
$18.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1848)
from
$26.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Upgrade your 1975 Ford Custom 500 with Top-Quality Air Intakes
When it comes to maintaining or upgrading your 1975 Ford Custom 500, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Air Intakes are key to keeping your Custom 500 functioning at its best. At Advance Auto Parts, we offer a wide selection of 25 Air Intakes for the 1975 Ford Custom 500, designed to meet your needs without breaking the bank.
From
Carburetor Kit
replacements to
Carburetor Parts
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Air Intakes for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Air Intakes for your 1975 Ford Custom 500 at great prices.
Our Air Intakes inventory for this model
ranges from just $4.29 to $1,400.99, with
an average price of $472.70.
Our 25 Air Intakes in stock come from 8 trusted brands, so you’re sure to find the right part for your 1975 Ford Custom 500 without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1975 Ford Custom 500, we stock popular OEM and aftermarket Air Intakes from top names
like Felpro Edelbrock, and more.
Felpro Air Intakes
start at just $4.29 and boast an impressive 4.6 stars average rating from customers.
With 70 customer reviews and counting, our 1975 Ford Custom 500 Air Intakes have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Air Intake upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1975 Ford Custom 500 is always ready to roll. We’re committed to providing you with everything you need to keep your Custom 500 in top shape, all in one place.
Start shopping confidently below for your 1975 Ford Custom 500!
Best-Selling Carburetor Kits for 1975 Ford Custom 500s
Enhance the driving experience in your Ford with 2 quality Carburetor Kit components, starting at $24.99.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1848)
from
$26.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1762)
from
$24.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Most Popular 1975 Ford Custom 500 Carburetor Parts
Customize your Ford with 9 Carburetor Parts products
like Carburetors and
Carburetor and Injector Mount Gaskets, all
priced under $921.99.
Holley – Street Carburetor: 500 CFM, Manual Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-4412S)
from
$549.99
The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to push you to the finish line on Saturday night, the Holley 0-4412 Performance 2BBL is the perfect choice.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
United Carb – Carburetor-Remanufactured (Part No.7-7574)
from
$254.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Holley – Performance and Race Carburetor: 500 CFM, No Choke, 2 Barrel, 2300 Bore, Single Inlet (Part No.0-4412HBX)
from
$921.99
Xtreme Performance – Holley Ultra XP(TM) Circle Track Carburetors! Ultra XP carbs are 38% lighter than our original HP, have fuel capacity that is 20% greater and 30 other new features! They’re available in our Hard Core Gray(TM) hard coat anodized finish with Black(TM) billet for improved corrosion protection & also available in natural tumble-polished aluminum with Black(TM) metering blocks and base plate. The Aluminum Ultra XP Cirlce Tracks are available in 650 & 750 CFM’s. Holley Ultra XP carburetors are Specifically Calibrated for Circle Track & offer new features such as anti-siphon valve in the main body; high capacity HP bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, fully tunable billet metering blocks, billet base plate, wedge floats, adjustable secondary linkage and knurled (hand adjustable) curb idle screws. Holley Ultra XP carburetors are the ultimate in square bore race carburetors!
Product Features:
See More
Product Features:
- All Aluminum Construction
- No Choke Tower For Unobstructed Airflow
- Air Bleeds Moved Outward Allow Smoother Transition Of Airflow
- Down-Leg Boosters For Improved Fuel Signal
- Contoured Hex Head Squirter Screw For Streamlined Airflow
- Internal Pump Passage On Metering Block w/Tunable Bleed Off
- Built In Drain Plug Provides Easy Access to Empty Bowl
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Window On Both Sides Of Bowl For Fuel Level Adjust
Holley – Performance and Race Carburetor: 500 CFM, No Choke, 2 Barrel, 2300 Bore, Dual Inlet, Shiny (Part No.0-4412BKX)
from
$819.99
Xtreme Performance – Holley Ultra XP(TM) Circle Track Carburetors! Ultra XP carbs are 38% lighter than our original HP, have fuel capacity that is 20% greater and 30 other new features! They’re available in our Hard Core Gray(TM) hard coat anodized finish with Black(TM) billet for improved corrosion protection & also available in natural tumble-polished aluminum with Black(TM) metering blocks and base plate. The Aluminum Ultra XP Cirlce Tracks are available in 650 & 750 CFM’s. Holley Ultra XP carburetors are Specifically Calibrated for Circle Track & offer new features such as anti-siphon valve in the main body; high capacity HP bowls which feature 20% more fuel capacity to eliminate starvation, integrated fuel shelf to minimize fuel aeration and internal baffling to control fuel slosh. Other features include all aluminum construction, fully tunable billet metering blocks, billet base plate, wedge floats, adjustable secondary linkage and knurled (hand adjustable) curb idle screws. Holley Ultra XP carburetors are the ultimate in square bore race carburetors!
Product Features:
See More
Product Features:
- All Aluminum Construction
- No Choke Tower For Unobstructed Airflow
- Air Bleeds Moved Outward Allow Smoother Transition Of Airflow
- Down-Leg Boosters For Improved Fuel Signal
- Contoured Hex Head Squirter Screw For Streamlined Airflow
- Internal Pump Passage On Metering Block w/Tunable Bleed Off
- Built In Drain Plug Provides Easy Access to Empty Bowl
- Fuel Bowl Provides 20% More Fuel Capacity Controls Slosh
- Clear Sight Window On Both Sides Of Bowl For Fuel Level Adjust
Holley – Street Carburetor: 500 CFM, Manual Choke, 2 Barrel, 2300 Bore, Single Inlet, Gold Dichromate (Part No.0-4412C)
from
$665.99
The 0-4412 is designed as a stock replacement for 2BBL street applications as well as being mandated for some oval track racing sanctioning bodies. Whether you are looking for a replacement carburetor to replace your tired and worn factory 2BBL or one to
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
- Does Not Work w/A.O.D. Transmissions
- Installation/Tuning DVD Incl.
Holley – Street Avenger Carburetor (Part No.0-80350)
from
$652.99
Product Features:
See More
- Vibratory polished for good looks
- Optimized street calibration that works-out-of-the-box
- Factory preset electric choke for easy startups (Range identified and restricted for easy no trouble adjustment)
- Built in No Trouble fuel inlet filter
- Street Avenger fuel metering system provides precise fuel control for great low end torque and awesome acceleration
- Compatible with GM, Chrysler, and Ford A/T kickdown linkage. Additional parts may be required.
- Gen IV No Trouble power valve
- Limited warranty – Guaranteed to be free from defects in material and workmanship for the life of the product!
- 100% wet-flow tested by Holley technicians to assure it arrives ready to run!
Holley – Performance and Race Carburetor: 500 CFM, No Choke, 2 Barrel, 2300 Bore, Single Inlet (Part No.0-4412CT)
from
$649.99
Competition fuel curves provide safe and reliable horsepower for high performance race engines.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Corrosion Resistance w/Classic Look
- Man. Choke Cable Hand Controlled For Cold Start Control
- 50CC Accelerator Pump For Add. Fuel Under Initial Acceleration
- Power Valve Blow-Out Protection
- 100% Wet-Flow Tested To Assure It Arrives Ready To Run
Holley – Street Carburetor: 500 CFM, Electric Choke, 2 Barrel, 2300 Bore, Single Inlet, Shiny (Part No.0-80500)
from
$614.99
Street Avenger carburetors are known to bolt on right out of the box and Holley is excited to announce the addition of our new 2bbl Street Avenger models available in 350 and 500 CFM. Street Avenger carburetors have great features such as optimized street calibrations; three vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included 3/8″ fuel line connection so there are no unnecessary trips back to the parts store.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Built In No Trouble Fuel Inlet Filter
- Provides Precise Fuel Control For Low End Torque/Acceleration
- Gen Iv No Trouble Power Valve
- Three Vacuum Ports [1 Pcv/Brake 1 Timed Spark 1 Full]
- Limited Lifetime Warranty Defects In Material/Workmanship
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Victor Reinz – Carburetor Mounting Gasket (Part No.71-13696-00)
from
$16.99
Product Features:
See More
- Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
- Dana engineering-approved for fit, form and function
- Meets or exceeds OE specifications
Top Picks for 1975 Ford Custom 500 Throttle Bodies & Carb Parts
Upgrade Ford Custom 500s with top-quality Throttle Bodies & Carb Parts parts, including 2 OEM and aftermarket selections for your 1975 model.
Felpro – Carburetor Mounting Gasket (Part No.60716)
from
$7.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Fuel Injection Throttle Body Mounting Gasket (Part No.ES 70582)
from
$15.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
In-Demand Air Cleaner Parts for 1975 Ford Custom 500s
Select from 2 premium Air Cleaner Parts parts for your 1975 Ford Custom 500, with prices ranging from $4.29 to $46.99.
Felpro – Air Cleaner Mounting Gasket (Part No.60038)
from
$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Most Sold 1975 Ford Custom 500 Intake Manifold Parts
Explore our best-selling Ford parts for the 1975 Custom 500 among 10 OEM and aftermarket options starting from $26.99.
Felpro – Valley Pan Gasket Set (Part No.MS 96020)
from
$45.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- RIGHT TYPE – Valve stem seals designs are application-specific for the repair occasion using either deflector (umbrella) seals, O-ring style or positive seals
- QUALITY MATERIALS – Each valve stem seal features materials based on the specific application for your vehicle repair
- ENGINEERING EXPERTISE – Parts are reviewed, validated and approved by Fel-Pro engineers through rigorous research, development and testing
- INSTALLATION AID – Installation tool included to protect inner lip of seal from damage during seal installation
- COVERAGE – Available for domestic and foreign nameplate vehicles
Felpro – INTAKE MANIFOLD GASKET SET (Part No.MS 90361)
from
$26.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES – Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE – Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED – Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR – Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Mr. Gasket – Intake Gasket (Part No.222)
from
$45.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.brbrFits all Ford 351M/400 – 4V or 4-Barrel heads.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Die-cut for an excellent fit
- Can be trimmed if necessary for modified port applications
- Complete with manifold end seals
- For OE replacement, high performance street, drag race and oval track use
Edelbrock – Performer 400 Intake Manifold for 1971-82 Ford 351/M400 (Part No.2171)
from
$443.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Holley EFI – KIT; FORD 351W HI-RAM; 95MM EFI BLACK (Part No.300-241BK)
from
$1400.99
KIT; FORD 351W HI-RAM; 95MM EFI BLACK
Holley EFI – MFLD KIT; FORD 351W HI-RAM; 95MM EFI (Part No.300-241)
from
$1400.99
MFLD KIT; FORD 351W HI-RAM; 95MM EFI
Holley EFI – KIT; FORD 351W HI-RAM; 105MM EFI BLACK (Part No.300-242BK)
from
$1400.99
KIT; FORD 351W HI-RAM; 105MM EFI BLACK
Holley – 351W Ford Hi-Ram Carbureted Manifold Base (Part No.300-243)
from
$819.99
Product Features:
See More
- Plenum Top Gasket Type – 3/32″ Round O-ring Cord
- Manifold is designed for a 9.5″ deck height.
- Requires the Use of Holley EFI Dual Sync Distributor – 565-111
- For carbureted applications use MSD PN 85787 Ford 351W Distributor with Steel Gear
Edelbrock – Performer Ford 400 EGR Intake Manifold (Part No.3771)
from
$553.99
3) For off-highway use, non-EGR 4V system with an Edelbrock #8714 4V spacer.
Product Features:
See More
Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
- Accepts Late-Model Choke And Waterneck
Edelbrock – Performer 351-W Intake Manifold for S/B Ford 351 Windsor (Part No.2181)
from
$402.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Stock Replacement
- 50-State Street Legal
Top-Rated Air Intakes Brands For Your 1975 Ford Custom 500
Shop for the best-rated brands offering Air Intakes and other products for your 1975 Ford Custom 500s. Below you’ll find some of our best rated Air Intakes from Felpro and Edelbrock, and more. Air Intakes from these brands that fit a 1975 Custom 500 start at just $4.29 and are rated as high as 4.6 stars. OEM and aftermarket Air Intakes don’t get more top quality, durable, and affordable than from the brands below.
Popular Felpro 1975 Ford Custom 500 Air Intakes
When it comes to maintaining or upgrading your 1975 Ford Custom 500, using quality Air Intakes is essential to ensure durability and a perfect fit. Felpro ticks all of those boxes. We offer a wide selection of Felpro Air Intakes, specifically designed for the 1975 Ford Custom 500. With over 3 Felpro brand Air Intakes in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $4.29, with an average price of just $19.42. Plus, with over 43 customer reviews and an average rating of 4.6 stars, you can trust that our Felpro Air Intakes will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
Popular Edelbrock 1975 Ford Custom 500 Air Intakes
Edelbrock auto parts is one of the highest quality Air Intake brands in the market. Any 1975 Ford Custom 500 owner should feel confident when installing genuine Edelbrock parts in their vehicle. To ensure the best fit and performance for your 1975 Custom 500, Advance Auto Parts carries a full inventory of 1 Edelbrock Air Intakes. Plus you will be keeping your Ford in peak condition while saving money because prices on these Edelbrock Air Intakes range up to $46.99, plus, with more than 19 customer reviews and an impressive 4.4 stars average rating, you can be confident the Fram Air Intakes below will deliver on both quality and value.
FAQs for 1975 Ford Custom 500 Air Intakes
Which Air Intakes are best-sellers for 1975 Ford Custom 500s?
Out of 25 Air Intakes that fit 1975 Ford Custom 500s, the following parts are the top sellers:
- Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (17140002) – $46.99
- Fuel Injection Throttle Body Mounting Gasket (3504263) – $15.99
- Intake Gasket (17360239) – $45.49
What’s the price range for 1975 Ford Custom 500 Air Intakes?
Air Intake prices for the 1975 Ford Custom 500 start at $4.29 and go up to $1,400.99 for the most premium parts.
What’s the average price of a Air Intake for a 1975 Ford Custom 500?
The average price for Air Intakes for the 1975 Ford Custom 500 is $472.70. Keep in mind the variety of part types within our Air Intake category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Air Intakes for other Ford Custom 500 model years?
What are the cheapest Air Intakes for my 1975 Ford Custom 500?
The cheapest 1975 Ford Custom 500 Air Intakes we carry in stock are:
- Air Cleaner Mounting Gasket (5785448) – $4.29
- Carburetor Mounting Gasket (5182409) – $7.99
- Fuel Injection Throttle Body Mounting Gasket (3504263) – $15.99
- Carburetor Mounting Gasket (50259811) – $16.99
- Carburetor Repair Kit (12592541) – $24.99
What are the top-rated Air Intakes that fit the 1975 Ford Custom 500?
Out of 70 reviews by customers, our 1975 Ford Custom 500 Air Intakes have an average customer rating of . These are some of the highest-rated Air Intake types for the 1975 Ford Custom 500 and their top-rated products:
- Intake Manifold Parts
- Valley Pan Gasket Set (5186064) – $45.99
- INTAKE MANIFOLD GASKET SET (5184568) – $26.99
- Throttle Bodies & Carb Parts
- Valley Pan Gasket Set (5186064) – $45.99
- INTAKE MANIFOLD GASKET SET (5184568) – $26.99
- Air Cleaner Parts
- Valley Pan Gasket Set (5186064) – $45.99
- INTAKE MANIFOLD GASKET SET (5184568) – $26.99
What types of Air Intakes do you sell for my 1975 Ford Custom 500?
As of 3/1/26, these are some of the most in-demand types of Air Intakes for a 1975 Ford Custom 500:
Can I get help with 1975 Ford Custom 500 Air Intake orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Air Intakes and more.
What is your return policy for Ford Custom 500 Air Intakes?
Advance Auto Parts keeps returns simple. For new Ford Custom 500 Air Intakes and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
