Name: Spartan Locker For Toyota 95" Landcruiser With 30 Spline Axles, Includes Heavy-Duty Cross Pin Shaft
Brand: USA Standard Gear
SKU: 17033
Price: 603.99 USD

from

$603.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 9.5″ Landcruiser with 30 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$358.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 1990 and down Toyota Landcruiser
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

from

$564.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Toyota 9.5″ Landcruiser
9.50″ ring gear diameter
27 spline pinion
10 ring gear bolts
4.11 ratio

from

$15.99

Toyota Landcruiser pinion nut, coarse spline, LARGE. 22mm x 1.5mm.

Product Features:

Pinion nut
Fits Toyota Landcruiser with 10 spline pinion

from

$161.99

Ring gear bolt kit for Toyota Landcruiser.

Product Features:

Fits standard rotation Toyota Landcruiser
Included are ring gear bolts and nuts

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$115.99

Bearing race driver front Toyota 7.5″, 8″, Landcruiser, and the Suzuki Samurai. No return. (TOY30306).

Product Features:

Bearing race driver
Fits 30306 race
All steel construction

from

$1099.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts.

Product Features:

Fits Toyota 9.5″ Landcruiser with 30 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$376.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$27.99

Product Features:

Cross pin shaft
Fits Toyota Landcruiser

from

$311.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits reverse rotation Toyota Landcruiser
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$551.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$131.02

Differential Bearing

from

$21.99

Product Features:

Ring gear bolt and nut kit
Fits Toyota Landcruiser
Includes one bolt and one nut

from

$31.99

Product Features:

Pinion gear thrust washer
Fits Toyota Landcrusier

from

$441.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Toyota Landcruiser reverse rotation front
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve, thread locker, marking compound with brush and silicone.

from

$30.99

Toyota Landcruiser crush sleeve. Approx 2.220″ long.

Product Features:

Crush sleeve
Fits Toyota Landcruiser
2.220″ tall

from

$9.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$21.99

Product Features:

KIT SHIM SIDE 9.5″ GM

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$19.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$24.99

Landcruiser standard Open side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits Toyota Landcrusier

from

$57.99

Yukon small hole yoke for ’82 and older Toyota 8″ and Landcruiser with 27 spline. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features: