from

$49.49

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

Fits MSD/GM V8 Distributors
Made from high quality materials
Brass terminals
High dielectric properties

from

$153.99

Beautifully chrome plated. Complete with drain plug, washer & bolts (stock depth). Chrome-plated dipsticks with tubes sold separately.

Product Features:

Chrome plated
Includes drain plug/washer/bolts

from

$369.99

HoleShot 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$85.09

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$48.49

All MSD extra duty distributor caps are designed with performance in mind and are molded from high quality, voltage insulating material and use low resistance terminals.

Product Features:

Update The GM Points Cap w/MSD Performance
High Quality; Voltage Insulating Material
Low Resistance
Performance replacement part

from

$72.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$499.99

Power Train

from

$211.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:10 & DWN

from

$78.99

Replace your stock black engine pulleys with a pair of chrome plated steel pulleys from Mr. Gasket. The pulleys are highly polished then chrome plated. Designed for small and big block Chevrolet engines with 5/8 inch water pump shaft.

Product Features:

Highly Polished For Lasting Beauty
Single Groove
w/Long Water Pump

from

$100.99

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

10-15% More Energy
Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Highly Specialized Silicone Magnetic Steel Cores
Standard Motor Products SMP Dr-31
MSD 8225

from

$43.99

These are high quality gaskets that works well on those hard to seal applications. The low density fiber & rubber blend gasket material seals those minor head imperfections with a low clamp force. At .312 inch, the extra thickness can also offer slightly more clearance for roller rockers. Ideal for all those high performance applications where you take the valve covers off and on a lot, and sticking is a problem.brbrFits all 1965-2000 Chevy Big Blocks: 366,396,402,427,454 including GM (General Motors) Gen VI Crate Engines like the 502 and 572.

Product Features:

These Are A Cork Rubber Blend
Extra Thick 5/16 In Creates Positive Seal
Also Available In Standard Thickness
For OE Replacement And High Performance Apps

from

$165.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 130 gph Free Flow
Shutoff Pressure Pre-Set From 7.5 To 9 PSI
Fuel Pressure Regulator Required Recommend P/N 12-704
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT

from

$15.99

Bolts on with existing timing cover bolts. It is chrome plated steel, which makes is a better compliment to a chrome timing cover. It also has an adjustable red timing pointer. This allows for better visibility and helps you set your timing more easily. Just loosen the screw, set the pointer to the desired initial timing level, and screw it back down. Then you’ll be able to more clearly see if your timing is where you want it when checking your timing.

Product Features:

Bolts on using existing timing cover bolts
Chrome finish compliments chrome timing covers
Red adjustable pointer makes it easier to check timing

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$20.99

Product Features:

Made from HYPER-Flex Polyurethane

from

$1009.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
64cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$105.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance And Fuel Economy
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$14.99

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

2 in. adjustable range
Includes necessary hardware
Chrome plated
Individually packaged

from

$237.99

Exhaust Manifold/Header

from

$38.99

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

Gains Both Performance and Longevity
Will Handle Any and All Torque
Out Lasts Rubber

from

$21.99

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$42.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$209.99

Give your vintage vehicle’s exhaust system an upgrade with a DynoMax? dual header kit. Designed to attach to OE manifolds, it features a special reducer that allows for a variety of mounting options.

Product Features:

COMPATIBILITY — Designed for a variety of full-size 1973-89 GMC 4WD trucks and Chevrolet 4WD SUVs; see product information for compatibility and engine spec
BUILD IT YOURSELF — Design and custom fabricate your own exhaust system with this kit that attaches to OE manifolds
FLEXIBLE MOUNTING — Special reducer design allows for a variety of mounting options
IMPROVED FLOW CAPACITY — Smooth bends improve flow capacity over traditional bends
SPECS — Extra-long tailpipes with side exits with a full 2.25-in. diameter; tailpipes exit each side of vehicle behind rear tires
COMPLETE SOLUTION — Includes all the necessary clamps, hangers, flanges, gaskets, mounting hardware, intermediate, extension and tail pipes
PREMIUM MATERIALS — Made from quality aluminized steel for durability and long life
PREMIUM MATERIALSÿ–ÿMade from quality aluminized steel for durability and long life
BETTER TOGETHER — Complete your system with premium DynoMax mufflers and DynoMax accessories for a complete performance exhaust system
WARNING — Not legal for use on pollution-controlled motor vehicles

from

$31.99

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Withstands Intense Exhaust Heat
Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Deteriorating
Anti-stick Properties
Easy Removal For Disassembly

from

$363.99

These Mr. Gasket chrome alternators are remanufactured to exceed original equipment specifications for maximum dependability.

Product Features:

Fits Most 1966-’72 GM Vehicles
Bolt Spacing 6.6″
80 Amps
GM 10DN Style Alternator
Chrome Plated Finish
includes V-Belt Pulley – 1-Groove
Use w/ OEM Style Regulator

from

$42.49

Fits GM (General Motors) Powerglide transmissions with an aluminum case. Chrome plated dipstick that includes O-ring for a positive seal.

Product Features: