1974 Ford E-200 Econoline Distributors

A distributor’s performance is only as good as its drive gear. MSD Performance has put a great deal of effort into researching and testing a variety of metallurgical compositions, heat treating and coatings to provide you with a durable, accurate and strong distributor gear. MSD engineers have built test fixtures and spent hundreds of hours testing and evaluating the metallurgy of our gears. The result is a special alloy gear that is treated to a low-friction coating process. To you this means long life, an easy break-in period and reliable performance.

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

“Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “”arc-thru”” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.”

“Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “”arc-thru”” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.”

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed.

Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system or operating system fault.

In the world of modern engine design, it’s hard to beat a hydraulic roller camshaft for all-around performance. It’s crucial to match the distributor gear with the cam material to prevent premature failure of the cam or distributor gear which can lead to engine damage.

TSP Pro Series Pro Billet Distributor is for the racer who needs added spark and precision for their high performance power plant. It features a high quality, fully adjustable mechanical advance and an accurate magnetic pickup trigger. The CNC-machined aluminum body and hardened steel shaft, guided by a sealed ball bearing on top and a sintered steel bushing on the bottom, ensure stability up to 10,000 RPM. The dielectric cap features bolt-down and twist-lock capabilities. It has solid brass terminals and comes with a color-matched wire retainer.

TSP Ready to Run Distributor offers performance and convenience at a great price. It features a CNC-machined billet aluminum body and hardened steel shaft, with a sealed ball bearing on top and a sintered steel bushing on the bottom. Its easy-to-change module means you won?t need to use an external ignition box, and its small size will fit most applications. It has a clip-on cap with solid brass terminals and a color-matched wire retainer.

MSD now offers Ford distributors with steel gears for use with hydraulic roller cams.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

“Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “”arc-thru”” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.”

BWD SELECT designs, specifies, and manufactures replacement parts with one goal in mind-make them the very best. To maximize performance and longevity, we use the finest materials and improve on OE specifications, whenever possible.

The distributor cap & rotor are just two pieces of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Flame Thrower Street/Strip distributors have a speciallFlame-Thrower Street/Strip distributors have a specially designed HEI distributor module and coil combination which operates without misfire beyond 7500 RPM. That’s nearly 3000 RPM higher than most stock HEI Distributors. Race HEI Distributors feature an electronic HEI Distributor module and 50,000 volt coil combination that optimizes spark energy and peak current to the spark plug in the 6000 to 8500 RPM range.y designed module and coil combination which operates without misfire beyond 7500 RPM

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

This special com­bination of bronze and nickel creates high-strength gear teeth that are less prone to wear even with high-volume oil pumps.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

This distributor drive gear is designed to match the fit, function and appearance of the original part on specified vehicles, and is engineered for durability and reliable performance.

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.