1974 Dodge Coronet Differentials

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Chrysler 7.25″

Worn or damaged differential end yoke causing driveline Vibrations- This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• KIT BRG & SEAL CHRYSLER 9.25″

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Chrysler 8.25″ with 27 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Redline Heavy Shockproof Gear Oil is formulated to provide lasting protection.

Product Features:

• Includes three quarts of Redline Shockproof oil

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side adjuster
• Fits Chrysler 7.25″ and 8.25″

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

These Yukon replacement diff covers are a direct bolt-on.

Product Features:

• Fits Chrysler 8.25″
• Steel

Product Features:

• CHRY 10BLT 8.25+8.36 R&P-4.56 RATIO

Product Features:

• CHRY 8 3/4″ RING GEAR BOLTS C 8.25″

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Yukon Gear & Axle manufactures a full line of top-quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers, and other general maintenance items. You can count on Yukon to fulfill all your differential small parts needs.

Product Features:

• Belleville plate, non-splined
• Fits Dana Spicer 44 Power Lok

Product Features:

• PINION SHIM 8 3/4″ EARLY

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Fits M86610 race
• All-steel construction
• For accurate installation of bearing races

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Right hand adjuster lock for 9.25″ GM IFS.

Product Features:

• Standard open carrier case
• Does not include spider gears
• Fits Chrysler 8.25″
• 29 spline only
• ABS and non-ABS compatible

For vehicles that are driven daily, the Power Trax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Power Trax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Power Trax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Power Trax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds.

Product Features:

• The Power Trax Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Power Trax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
• Power Trax lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
• Power Trax offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
• Power Trax ia an Extreme Traction System

Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.

Product Features:

• Fits 1976 and up Chrysler 8.25″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon 4340 Chrome-Moly replacement inner axle for Dana 60 with a length of 16.17″ and 35 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
• Dana engineering-approved for fit, form and function
• Meets or exceeds OE specifications.

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Yukon yoke for GM 12 bolt car & truck, 1330 u/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. All Yukon yokes come with a Limited warranty against manufacturing defects.

Product Features:

• Fits 1976 and up Chrysler 8.25″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side adjuster lock bolt
• Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″

Product Features:

• MINI-INSTLTN KIT-CHRYSLER 7 1/4″

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut washer
• Fits Chrysler 8.75″ with 10 spline pinion