1973 Dodge Coronet Differentials

Product Features:

• Flat drive plate
• Fits Dana Spicer 44 Powr Lok

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• MASTER KIT CHRYS. 8.75″ 1.875″ PINI

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

• Includes three quarts of Redline Shockproof oil

Product Features:

• KIT SHIM PINION

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

• Pinion nut washer
• Fits Chrysler 8.75″ with 10 spline pinion

Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7290 U/joint size (1350 with U/joint adapter.) All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 8.75″
• 10 spline
• 7290 u-joint size
• Inside snap ring design
• 2.625″ snap ring span
• 1.125″ cap diameter
• Strap style

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Chrysler 8.75″ ’42’ case housing with 25520 carrier races
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

8.25″ Chrysler pinion gear thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits Chrysler 8.25″

Yukon standard open spider gear kit for 7.25″ Chrysler with 25 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Chrysler 7.25″ rear with open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Yukon axle kit for Chrysler 8.75″. This kit contains two green bearings, ten axle studs and two cut to length axles that fit A, B & E body cars, 5 x 4.5″ pattern.

Product Features:

• 30 spline
• 5 x 4.5″ bolt pattern
• Cut to length design fits 28″-32″ applications
• Axle kit
• Includes two axles, two green bearings and 10 axle studs

Yukon Performance 2-1/16″ deck steel spool for 8.75″ Chrysler with 30 spline axles. Spool uses 2.050″ journal bearings (LM104949/12). Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 8.75″ with 30 spline axles
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Pinion seal for 8.75″ Chrysler or for 9.25″ Chrysler with 41 or 89 housing.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Chrysler 8.75″ with ’41’ and ’89’ case housings and 2000 and down Chrysler 9.25″

Product Features:

• MINI INSTALL KIT CHRYSLER 8.75 8 3/4″ EARLY 742 CASE

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Chrysler 8.75″ ’41’ case
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction

This differential ring and pinion directly replaces the original equipment on specific vehicle years, makes and models.

Product Features:

• Direct replacement – this ring and pinion set matches the fit and function of the original components on certain vehicle applications
• Effective fix – eliminates grinding and whining from failed original bearings
• Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
• Trustworthy quality – backed by team of designers and engineers in the United States

Side gear thrust washer for 7.25″ Chrysler.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 7.25″

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

8.75″ Chrysler 89 solid crush sleeve replacement spacer, preload. This item is compatible with ’89 case dropouts only.

Product Features:

• Crush sleeve eliminator kit for Chrysler 8.75″ with ’89’ case housing

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

Differential carrier side bearing screw adjuster for Chrysler 7.25″ and 8.25″.

Product Features:

• Side adjuster
• Fits Chrysler 7.25″ and 8.25″

Product Features:

• Dropout housing
• Fits Chrylser 8.75″
• ’89’ case design
• Nodular iron for added strength

Product Features:

• Pinion nut
• Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion