from

$788.99

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application. The dual spring design creates a stronger valve spring that can easily handle the increased lift found in extreme stress applications. COMP Cams Dual Valve Springs exceed the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 112 lbs. @ 1.900″, Open Pressure: 355 lbs. @ 1.200″
O.D.: 1.509″, I.D.: 0.697″
Dual valve springs with damper

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$92.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Assures Longer Lasting Cab to Bed Alignment
Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$337.99

This Spectre polished aluminum oil pan is designed to fit 1955-’79 small block Chevrolet 283-350 engines with a driver’s side dipstick (except 1962-’67 Chevrolet II and Corvette with stock exhaust). This oil pan is made from a heavy die-cast polished aluminum featuring a finned diamond design. The stock oil capacity is maintained at 4 quarts and uses a 1975 and later gasket with thick front seal. The required mounting fasteners are included.

Product Features:

Stock 4 quart capacity
Polished die-cast aluminum
Finned diamond design finish
Includes mounting fasteners

from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$23.79

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

Fits Chevy engines
Includes a 1/2 inch NPT threaded hole for by-pass hose
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$53.99

When a high pressure fuel pump is run with a steel roller cam core, the stock fuel pump pushrod is not compatible with the steel core. You can damage an expensive roller cam as a result of wear at the fuel pump lobe. COMP Cams offers several fuel pump pushrods for various applications.

Product Features:

Lightweight tubing with bronze tip for steel cams
5.75″ Length
Eliminates wear at the fuel pump lobe often caused by a stock fuel pump pushrod

from

$369.99

HoleShot 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$48.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$108.99

What better way to check you oil level by using one of B&M’s transmission fluid dipsticks? The cap screws into the tube and is O-ring sealed, while the base of the tube has a sealing grommet where it goes into the transmission.

Product Features:

Automatic Transmission Dip Stick
Mounts to bellhousing
Sold as a kit
Natural finish
Fits TH350 & TH350C

from

$27.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$366.99

Designed to fit Hooker Competition header, Manifold or catalytic converter back applications. Cat-back kits install behind the converter and all other applicable emission control devices.

Product Features:

Reducer Flex-Tubes
Reduces Backpressure
Hardware Included
Instructions Included

from

$100.99

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

10-15% More Energy
Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Highly Specialized Silicone Magnetic Steel Cores
Standard Motor Products SMP Dr-31
MSD 8225

from

$74.99

Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:

Made of Superior Hyper-Flex+ Material
Adds Dramatic Amount of Performance/Durability
Helps Vehicle Be in Control
Allows the Suspension to Function Properly

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$107.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$164.99

This Small Block Chevrolet Steel Timing Cover features a welded thrust plate tab for use with a cam button. It allows adjustment for correct end play with out additional modifications and includes gaskets, seal and bolts and has a black powder coated finish.

Product Features:

Features a welded thrust plate tab for use with a cam button
Allows adjustment for correct end play without additional modifications required
Includes gaskets, seals and bolts
Black powder coated finish

from

$463.99

Product Features:

Fuel Economy From The Engine
Leak Test For Max Performance
Ceramic Headers
Rust And Corrosion Resistance
Mandrel-Formed Power Plenum
Leakproof O-Ringed Port Seals
Include All Mounting Hardware

from

$626.99

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

Vibratory Polished For Good Looks
Optimized Street Calibration That Works Out Of The Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
No Unnecessary Trips Back To The Parts Store
Limited Lifetime Warranty
100% Wet-Flow Tested To Assure It Arrives Ready To Run
Street Ready; Out Of The Box

from

$101.99

Product Features:

MINI SPOOL – DANA 44, 30 SPL.

from

$111.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$48.49

All MSD extra duty distributor caps are designed with performance in mind and are molded from high quality, voltage insulating material and use low resistance terminals.

Product Features:

Update The GM Points Cap w/MSD Performance
High Quality; Voltage Insulating Material
Low Resistance
Performance replacement part

from

$7.99

Spectre’s Harmonic Balancer Bolt Kit is designed to fit Chevrolet Small Block 265-400 V8 engines. This grade 8 bolt is 2-1/2 inches long, and features a plated finish for corrosion resistance. This kit also includes a security lock washer.

Product Features:

Fits Chevrolet Small Block 265-400 V8 engines
Features a corrosion resistant plated finish
Gold iridite finish
Grade 8 bolt, 7/16 inch-20 by 2-1/2 inches
Includes security lock washer

from

$16.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for repair applications
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$468.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM street-driven power. Dual-plane high-rise intake with 180 degree firing order. Produces incredible top-end horsepower. Retains good throttle response and acceleration. Larger plenum and runners maximize other upgrades. Edelbrock total power package maximizes gains. Available in cast, polished or endurashine finish.

Product Features: