1974 Buick Regal Performance and Racing Products

Name: Unilite Breakerless Ignition Conversion Kit
Brand: Mallory
SKU: 503M
Price: 176.99 USD

Below you will find various in-demand Buick Performance and Racing Products, components and accessories for your 1974 Regal. Advance Auto Parts has popular Regal parts like Performance Exhaust Products, Performance Engines, Performance Distributors and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Regal model years including 2003, 2004, 2011, 2012, 2013, 2014, 2015, 2016, 2017 and more. Select a category of 1974 Buick Regal Performance and Racing Products below and start saving instantly.

Popular 1974 Buick Regal Performance and Racing Products Categories

Performance Carburetors

Performance Engine Coolant Thermostats

Performance Fuel Pumps

Performance Coils

Performance Exhaust Mufflers

Performance Distributor Cap and Rotor Kits

Performance Shifters

Performance Distributors

Performance Engine and Transmission Mounts

Performance Water Outlets

Performance Radiator Caps

Performance Engine Cylinder Head Gaskets

Performance Differential Covers

Performance Front Shock and Struts

Performance Engine Intake Manifold Gaskets

Performance Engine Valve Springs

Performance Engine Valve Cover Gasket Sets

Performance Spark Plug Wires

Performance Chassis Bushing Kits

Performance Exhaust Manifold Gaskets

Performance Posi Units and Components

Performance Ignition Kits

Performance Upper Performance Control Arm Bushings

Performance Engine Rocker Arms

Performance Ring and Pinions

Performance Ignition Parts

Performance Points and Condensers

Performance Sway Bar Link Kits

Performance Lower Control Arm Bushings

Performance Brake Bleeders

Performance Tie Rod End Boots

Performance Transmission Shift Kits

Performance Vacuum Advances

Performance Ball Joint Boots

Performance Nitrous Systems

Nitrous Oxide Injection System Kit

Performance Torque Converters

Performance Transmission Rebuild Kits

Manual Transmission Main Shaft Race

Performance Rear Shock and Struts

Essential Performance and Racing Products for 1974 Buick Regals

from

$176.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$210.99

Performance Replacement HEI Distributor, direct plug-in with OE type connectors, GM HEI equipped Cars, Trucks (Pre-Computer). High dielectric strength cap, brass male towers. ACCEL Performance Replacement Distributors are the perfect choice for your daily driver or street machine. Using all new components, these distributors feature High-performance ACCEL Electronics. All new components-housings are either new castings or turned from billet stock, centerless ground shaft with oil lite bushings. High dielectric strength cap, balanced rotor. Male tower distributor cap with brass cap and rotor contacts (Ford and AMC Models feature screw-mounted wire retainer for the ultimate plug wire retention). Iron or steel distributor gear. Direct plug-in replacement with factory-type connectors for plug and play installation.

Product Features:

Direct Plug In Factory Replacement Plug And Play
CNC Machined 6061 T6 Billet Aluminum Housing
High Dielectric Strenght Thermoplastic Cap With Br
4 Topin Module With Dwell Control Triggers At 75 R
Easy Access Fully Adjustable Mechanical Advance
Adjustable Vacuum Advance
Includes Performance Coil
Fit non computerized vehicles

from

$10.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Lasts Longer
Looks Great

from

$17.09

Distributor Condenser

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$609.99

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine
New Turbine Hub
New Springs/Rollers In Stator

from

$94.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$104.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$32.99

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Product Features:

Manufactured from .020″ steel shim stock.
Thinner than composition head gaskets – increases engine compression.
Stress formed embossments seal extreme cylinder pressures.
For high performance street, drag race and oval track use.

from

$35.99

The Edelbrock valve cover gaskets #7546?provide excellent sealing integrity and conformability for easy installation. The multi-layer construction has two highly compressible, high rubber content, fiber-reinforced outside layers which are chemically bonde

Product Features:

0.1875 in. Thickness
Core-Reinforced-Composite Material
For Buick 400-455
Set of 2
Made In The USA

from

$40.99

Brake Bleeder Screws

from

$154.99

The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$42.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

from

$357.99

Product Features:

Incredible Improvement in Control
Maintains Proper Caster and Camber Alignment
Increase in Handling and Control
Greatly Reduce Wheel Hop on Quick Acceleration
Even Braking Control is Improved
Better Suspension Stability

from

$26.99

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features:

Made from HYPER-Flex Polyurethane
Allows Vehicle to Work At Maximum Efficiency
Easy to Install
Superior Performance and Greater Longevity
Lasts Much Longer Than OEM Rubber End Links

from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$7.69

CUP

from

$98.99

Product Features:

MINI SPOOL GM 10 BOLT 8 1/2″ 28 SPLINE

from

$451.99

The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$96.99

The traditional ACCEL combination of yellow wire and red spark plug boots has been added to these SuperStock Spiral Core 5000 Series wire sets, which feature color-matched wire and spark plug boots in blue, black, and red. With only 500 ohms/ft. of resistance, more ignition energy can reach the spark plug, producing a longer-lasting, hotter spark flame kernel. The results is higher performance through improved efficiency, quicker throttle response, and reduced emissions. This 8mm wire’s double silicone construction is rated to 550 degrees F. The high-gloss wire jacket resists moisture, chemicals, and heat extremes for longer life and great looks. The fiberglass braid adds greater pull strength and terminal retention, while the stainless steel spark plug terminals provide excellent long life, electrical conductivity, and corrosion resistance. Both universal and custom-fit applications are available for early and late model cars and trucks.

Product Features:

500 Ohms/ft Of Resistance
550 F Rated Silicone Jacket
Stainless Steel Plug Terminals
High RFI Suppression For Street And Strip Use
High-strength Fiberglass Braid Construction
8mm High Gloss Silicone Jacket
500 Ohms Resistance

from

$320.99

Product Features:

Easily Concealable
Install In Minutes
Quick Removal
No Obvious Signs Of Installation
No Obvious Signs Of Use

from

$104.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

Universal Floor Mount Application
Base Trimmed For Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$89.99

A true performance application component for cars, trucks, hot rods, racing/competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Unique Safety Interlock Design
Impervious to Vehicle Oils and Chemicals
Strong Enough Too Handle High Performance

from

$222.99

Product Features:

GM 10BL 7.5 &7.625 R/P 4.56 MGP

from

$191.99

RngPnn

Upgrade your 1974 Buick Regal with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1974 Buick Regal, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Buick or enhancing its overall performance, Performance and Racing Products are key to keeping your Regal functioning at its best. At Advance Auto Parts, we offer a wide selection of 90 Performance and Racing Products for the 1974 Buick Regal, designed to meet your needs without breaking the bank. From Performance Exhaust Product replacements to Performance Engines upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1974 Buick Regal at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.69 to $1,138.99, with an average price of $327.93. Our 90 Performance and Racing Products in stock come from 17 trusted brands, so you’re sure to find the right part for your 1974 Buick Regal without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1974 Buick Regal, we stock popular OEM and aftermarket Performance and Racing Products from top names like Mr. Gasket, Edelbrock, Energy Suspension, and more. Mr. Gasket Performance and Racing Products start at just $12.99 and boast an impressive 4 stars average rating from customers. Edelbrock and Energy Suspension also bring quality to the table, with Performance and Racing Products available starting at $9.99, and at an average 4 stars rating. With 297 customer reviews and counting, our 1974 Buick Regal Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1974 Buick Regal is always ready to roll. We’re committed to providing you with everything you need to keep your Regal in top shape, all in one place. Start shopping confidently below for your 1974 Buick Regal!

Best-Selling Performance Exhaust Products for 1974 Buick Regals

Enhance the driving experience in your Buick with 2 quality Performance Exhaust Product components, starting at $34.49.

show more show less

from

$133.99

This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$34.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

Most Popular 1974 Buick Regal Performance Engines

Customize your Buick with 15 Performance Engines products like Performance Engine Intake Manifold Gaskets, Performance Engine Cylinder Head Gaskets, and Performance Engine Coolant Thermostats, all priced under $825.99.

show more show less

from

$499.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$339.99

Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$26.99

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$111.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$27.49

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Complete with o-rings and mounting bolts
Features an o-ring style seal to prevent water leaks
Chrome plated
1/2″ NPT port can be used for various coolant temp related sensors or switches

from

$35.99

0.1875 in. Thickness
Core-Reinforced-Composite Material
For Buick 400-455
Set of 2
Made In The USA

from

$299.99

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$68.99

Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:

Five layer (graphite core/perforated steel outer layers) composite construction
Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
Provides excellent stability, compressibility and high temperature endurance
Coated with high temperature silicone to ensure sealing of engine fluids
Will not brinell (indent) aluminum cylinder heads
For high performance street, drag race and oval track use
Compatible w/High Octane Fuel
Compatible With Exotic Fuel

from

$94.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$43.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$825.99

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine
Dual Pattern Drive Lugs
New Turbine Hub
New Springs/Rollers In Stator

from

$665.99

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

3400-3800 RPM
Small And Big Blocks
Serious Performance
Furnace Brazed
Fully Balanced

from

$499.99

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$141.99

Product Features:

Non-Rotator Type
1.550 in. Outer Diameter
.190 Wire Size
Single Coil Spring Type
Set of 16

from

$106.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Top Picks for 1974 Buick Regal Performance Distributors

Upgrade Buick Regals with top-quality Performance Distributors parts, including 2 OEM and aftermarket selections for your 1974 model.

show more show less

from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$647.99

If you’re looking for a performance distributor for your Buick or Nailhead your search is over! MSD’s Ready-to-Run distributor incorporates a magnetic pickup that never wears out! Plus, the distributor has a built in ignition module so there is no need to mount an external MSD Ignition control. Not only do you get the benefits of electronic triggering, but your engine will awaken with the powerful sparks from the ignition module. This module delivers up to 7.5 A to the coil creating a stout inductive spark. This improves combustion of the fuel mixture resulting in quick starts, a smooth idle and great performance! Another advantage of an MSD distributor is the accurate and adjustable mechanical advance assembly. The advance curve is easy to adjust with different advance springs and stop bushings which are included. To top it off there is a vacuum advance canister and MSD’s strong cap and wire retainer.

Product Features:

Simple and clean three wire installation
CARB E.O. Approved
Does not require an MSD Ignition Control
Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
Mech. advance assem. can be locked out for crank trigger systems
QPQ coated polished steel shaft; guided by sealed ball bearings
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range

In-Demand Performance Ignition Products for 1974 Buick Regals

Select from 11 premium Performance Ignition Products parts for your 1974 Buick Regal, with prices ranging from $17.09 to $186.99.

show more show less

from

$112.99

HEI owners now have a choice to replace their stock coil with the MSD high energy unitized coil for GM HEI distributors. This coil is a direct replacement of the stock coil and offers increased spark energy when used with the MSD HEI module, PN 83645. The coil features special low induc?tance, high temperature windings which charge faster to give you increased spark energy at higher rpm. The premium epoxy filled construction is designed to withstand harsh race applications as well as the wear and tear that daily usage dishes out, and still deliver more spark energy to the spark plugs.

Product Features:

Direct performance replacement for GM HEI coil-in-cap dist.
70:1 Turns Ratio
Lower Primary Resistance Produces High Voltage Output
Full Power Sparks To 9000 Rpm w/PN[83647] MSD HEI Module

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$134.99

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$113.99

Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:

10-15% More Energy
Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Highly Specialized Silicone Magnetic Steel Cores
Similar to Standard Motor Products SMP Dr-32
Long Life And Great Looks

from

$105.99

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$186.99

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

Glass Filled Polyester Case
Longer Spark Duration
Increased Performance
No Energy Loss Due To Arcing
Includes Brass Contact Terminal

from

$176.99

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$112.99

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

8.8mm Graphite Suppression
Silicone Spark Plug Boots
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

HEI Adjustable Vacuum Advance Kit - Includes weights, camplate, and bushings - Improve performance

from

$55.99

HEI Adjustable Vacuum Advance Kit – Includes weights, camplate, and bushings – Improve performance

from

$17.09

Distributor Condenser

Most Sold 1974 Buick Regal Performance Fuel Systems

Explore our best-selling Buick parts for the 1974 Regal among 8 OEM and aftermarket options starting from $12.99.

show more show less

from

$12.99

This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.

Product Features:

Chrome Plated Steel
Comes With Gasket

from

$494.99

The Edelbrock 1411 Performer Series 750 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$428.99

The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$394.99

The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$451.99

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$12.99

Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Product Features:

Necessary if switching to electric fuel pump
Includes block off plate gasket
Includes chrome mounting bolts with washers
Triple chrome plated

from

$498.99

The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Electric Choke
4 Barrel Count
Square Bore
Electric Choke Installed from Factory
Smooth Secondary Transition
Includes Only Timed Vacuum Port
Includes EGR ; Fuel Vapor Outlet

from

$538.99

The Edelbrock 1412 Performer Series 800 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1412 Performer Series 800 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation. Dyno tests proved that the EPS 800 carb outperformed a Holley #3310 carb out-of-the-box by 26 ft-lbs. of torque and 22 hp on a small-block Chevy engine equipped with an Edelbrock Performer RPM power package

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet
Can Easily Calibrate with Rods and Jets

Top-Rated Performance and Racing Products Brands For Your 1974 Buick Regal

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1974 Buick Regals. Below you’ll find some of our best rated Performance and Racing Products from Mr. Gasket, Edelbrock, and Energy Suspension, and more. Performance and Racing Products from these brands that fit a 1974 Regal start at just $9.99 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Mr. Gasket 1974 Buick Regal Performance and Racing Products

When it comes to maintaining or upgrading your 1974 Buick Regal, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Mr. Gasket ticks all of those boxes. We offer a wide selection of Mr. Gasket Performance and Racing Products, specifically designed for the 1974 Buick Regal. With over 8 Mr. Gasket brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $12.99, with an average price of just $50.19. Plus, with over 28 customer reviews and an average rating of 4 stars, you can trust that our Mr. Gasket Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$68.99

This product is not rated

Ultra Seal: Head Gasket

“”

from
$48.09

This product is not rated

Thermocap Radiator Cap

“”

from
$27.49

This product is not rated

Water Neck

“”

Popular Edelbrock 1974 Buick Regal Performance and Racing Products

Edelbrock auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1974 Buick Regal owner should feel confident when installing genuine Edelbrock parts in their vehicle. To ensure the best fit and performance for your 1974 Regal, Advance Auto Parts carries a full inventory of 21 Edelbrock Performance and Racing Products. Plus you will be keeping your Buick in peak condition while saving money because prices on these Edelbrock Performance and Racing Products range from $35.99 to $1,138.99, plus, with more than 76 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

from
$35.99

This product is not rated

Valve Cover Gasket Set for Buick

“”

from
$1138.99

This product is not rated

Performer RPM 2 Carb/Plate Nitrous Systems for Dominator

“”

from
$498.99

This product is not rated

Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

“”

FAQs for 1974 Buick Regal Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1974 Buick Regals?

Out of 90 Performance and Racing Products that fit 1974 Buick Regals, the following parts are the top sellers:

High Performance 180 Degree Thermostat for Increased Flow (17360033) – $26.99
High Performance Sway Bar End Link Kit with Hardware (16360004) – $26.99
Fuel Pump Block-Off Plate (6121586) – $12.99

What’s the price range for 1974 Buick Regal Performance and Racing Products?

Performance and Racing Product prices for the 1974 Buick Regal start at $7.69 and go up to $1,138.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1974 Buick Regal?

The average price for Performance and Racing Products for the 1974 Buick Regal is $327.93. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Buick Regal model years?

Yes, we currently carry Performance and Racing Products for 38 model years of Buick Regals between 1973 and 2017. Performance and Racing Products are bought most frequently for the following model years: 2017, 2016, 2015, 2014, 2013, 2012, 2011, 2004, and 2003.

What are the cheapest Performance and Racing Products for my 1974 Buick Regal?

The cheapest 1974 Buick Regal Performance and Racing Products we carry in stock are:

CUP (50206003) – $7.69
Tie Rod Dust Boot (17360821) – $9.99
Ball Joint Dust Boot Set (22906820) – $10.99
Fuel Pump Block-Off Plate (6121586) – $12.99
Sbc Blk Off Plate W/Bolts (22905347) – $12.99

What are the top-rated Performance and Racing Products that fit the 1974 Buick Regal?

Out of 297 reviews by customers, our 1974 Buick Regal Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1974 Buick Regal and their top-rated products:

Performance Suspension Products
- Drag Shock-70/30:GM (Rear) (22905061) – $104.99

What types of Performance and Racing Products do you sell for my 1974 Buick Regal?

As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1974 Buick Regal:

Can I get help with 1974 Buick Regal Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Buick Performance and Racing Products and more.

What is your return policy for Buick Regal Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Buick Regal Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1974 Buick Regal Performance and Racing Products

Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)

Accel – Dist:Chev V8 Hei Vac W/Coil (Part No.59107C)

Energy Suspension – Ball Joint Dust Boot Set (Part No.9.13128R)

Mallory – Distributor Condenser (Part No.401)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Mallory – Distributor Wiring Harness (Part No.29349)

B & M – Holeshot 2400 (Part No.70419)

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Lakewood – Drag Shock-70/30:GM (Rear) (Part No.40310)

Mr. Gasket – Head Gasket (Part No.1130G)

Edelbrock – Valve Cover Gasket Set for Buick (Part No.7546)

Earls Performance Product – Brake Bleeder Screws (Part No.280029ERL)

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Moderate Sound (Part No.942451)

Mr. Gasket – Intake Gasket (Part No.143)

Energy Suspension – Hyper-Flex System (Part No.3.18111G)

Energy Suspension – High Performance Sway Bar End Link Kit with Hardware (Part No.9.8117R)

Accel – Distributor Cap And Rotor Kit (Part No.8124)

FAG US – CUP (Part No.LM48510)

Motive Gear – Differential Mini Spool (Part No.MS10-28)

Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)

Accel – 8Mm Super Stock Spiral Cust Bk (Part No.5048K)

Edelbrock – Concealed Nitrous Kits for Carbureted Applications (20-30 Hp) (Part No.70027)

Lakewood – Drag Shock-70/30:GM (Part No.40120)

Mr. Gasket – Thermocap Radiator Cap (Part No.2476BK)

B & M – Automatic Shifter, Quicksilver 4 Speed (Part No.80683)

Energy Suspension – Transmission Mount (Part No.3.1132R)

Motive Gear – Performance Differential Ring and Pinion (Part No.G875456)

Richmond Gear – RngPnn (Part No.GM75342TK)

Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Center Outlet, Non-Reversible, Aggressive Sound (Part No.942441)

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1479)

B & M – Tork Master 3000 (Part No.20402)

B & M – Tork Master 2400 (Part No.20404)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Mr. Gasket – Water Neck (Part No.2557)

Edelbrock – Valve Cover Gasket Set for Buick (Part No.7546)

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 4 Piece Set (Part No.1357)

B & M – Holeshot 3600 (Part No.20425)

B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)

B & M – Holeshot 2400 (Part No.20412)

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1125)

Accel – Distributor Cap And Rotor Kit (Part No.8124)

MSD Ignition – Distributor; Buick 455 V8; Ready-to-Run (Part No.8552)

MSD Ignition – High Energy Ignition Coil for GM HEI Distributors (Part No.8225)

Mallory – Unilite Ignition Module (Part No.605)

Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)

Accel – GM Hei Supercoil Red/White (Part No.140005)

Accel – Supercoil (Part No.140001)

Mallory – Distributor Wiring Harness (Part No.29349)

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)

Accel – Custom Fit Spark Plug Wire Set (Part No.8843)

Mr. Gasket – HEI Adjustable Vacuum Advance Kit – Includes weights, camplate, and bushings – Improve performance (Part No.6011)

Mallory – Distributor Condenser (Part No.401)

Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1515)

Edelbrock – Performer 1411 Carburetor: 750 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1411)

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)

Spectre – Sbc Blk Off Plate W/Bolts (Part No.42463)

Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)

Edelbrock – Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1412)