from

$86.99

Replacement shim kit for Dana 30, front & rear, also D36ICA & Dana 44ICA.

Product Features:

Complete shim kit for Dana Spicer 30 front and rear, also Dana Spicer 36

from

$125.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1330 u-joint size
3.625″ snap ring span
1.125″ cap diameter
Outside snap ring design
U-bolt style

from

$12.99

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

Roll pin for Dana Spicer 30 and Dana Spicer 44
0.235″ diameter

from

$27.99

Product Features:

Bulkhead fitting

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$7.99

Dana 28 & Dana 30 pinion gear Thrust washer. Also fits AMC Model 35 with 1.560″ side gear bore only.

Product Features:

Pinion gear thrust washer for Dana Spicer 25, 27 and 30

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$155.99

Yukon replacement standard open spider gear kit for Dana 30 with 27 spline axles and with or without quick disconnect. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 30 open differential with 27 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 30

from

$16.92

Pinion Seal, Red

from

$639.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. Does not fit Std. JK Carrier. Use YC D706008

Product Features:

Fits Dana Spicer 30 with 27 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$6.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
3/4″ x 16 thread

from

$151.99

Product Features:

Spider gear kit
Fits Dana Spicer 30 27 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$7.96

Differential Carrier

from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 25, 27, 30, 44 and 50

from

$13.99

Product Features:

O-ring for seal housing
Fits Dana Spicer 30 and AMC Model 35

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$299.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits standard rotation Dana Spicer 30 without crush sleeve
7.20″ ring gear diameter
26 spline pinion
10 ring gear bolts
4.56 ratio

from

$12.99

Product Features:

Cross pin shaft for Dana Spicer 30
Fits standard open differentials only

from

$18.99

Product Features:

Bulkhead quit connect fitting

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$172.99

Set-up carrier bearing kit (2 bearings, no races) LM501349. No return.

Product Features:

Set up bearing kit
Fits Dana Spicer 30
Easily slips on and off carrier journals to allow for easier carrier shim adjustment

from

$167.99

Yukon replacement standard open carrier case for Dana 30, 3.73 & up,bare. This case includes carrier shims, roll pin, ring gear bolts and a cover gasket. If purchasing this case for a D30 JK front, you will need to also purchase spider gear set YPKD30-S-27.

Product Features:

Standard open carrier case
Fits Dana Spicer 30
3.73 and up ratio only
Does not include spider gears
Includes ring gear bolts, carrier shim kit, roll pin, and cover gasket

from

$7.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$10.99

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
1.560″ I.D.
Fits standard open differentials only

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$279.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 30 rear
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$67.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Powr Lok button kit
Fits Dana Spicer 30, 44 and Chrysler 8.75″

1973 Volvo 164 Differentials

More 1973 Volvo 164 Differentials

Essential 1973 Volvo 164 Differentials

Yukon Gear – Replacement Shim Kit For Dana 30, Front & Rear, Also D36Ica & Dana 44Ica (Part No.55023)

Yukon Gear – Replacement Yoke For Dana 30, 44, And 50 With 26 Spline And A 1330 U/Joint Size (Part No.41020)

Yukon Gear – Dana 30 / 44 Roll Pin Replacement (Part No.33312)

Yukon Gear – Zip Locker Bulkhead Fitting (Part No.34001)

Yukon Gear – Dana 25 / 27 / 30 / 36 / 44 / 53 Pinion Nut Washer Replacement (Part No.33163)

Yukon Gear – Dana 28 & Dana 30 Pinion Gear Thrust Washer (Part No.33285)

Yukon Gear – Replacement Ring Gear Bolt For Model 35, Dana 25, 27, 30 & 44 – 3/8" X 24 (Part No.33038)

Yukon Gear – Replacement Standard Open Spider Gear Kit For Dana 30 With 27 Spline Axles (Part No.16073)

Yukon Gear – Replacement Cover Gasket For Dana 30 (Part No.23003)

SKF – Pinion Seal, Red (Part No.J701050573SKF)

USA Standard Gear – Spartan Locker for Dana 30 Differential with 27 Spline Axles, Includes Heavy-duty Cross Pin Shaft (Part No.17000)

Yukon Gear – Replacement Pinion Nut For Dana 25, 27, 30, 36, 44, 53 & GM 7.75" (Part No.33143)

USA Standard Gear – Open Spider Gear Set For Dana Spicer 30, 27 Spline (Part No.39005)

Professional Parts Sweden – Differential Carrier (Part No.J705017349PPS)

Yukon Gear – Replacement Outer Oil Slinger For Dana 25, 27, 30, 44 & 50 (Part No.33011)

Yukon Gear – O-Ring For Dana 30 & Model 35 Zip Locker Seal Housing (Part No.34005)

Yukon Gear – Dana 30 & Dana 44 Power Lok Bolt, Left Hand, & 8.75" Chrysler & 55P (Part No.33234)

USA Standard Gear – Ring & Pinion Replacement Gear Set For Dana 30 In A 4.56 Ratio (Part No.36026)

Yukon Gear – Replacement Cross Pin Shaft For Standard Open Dana 30 (Part No.33316)

Yukon Gear – Zip Locker Bulkhead Quick-Disconnect Fitting (Part No.34038)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

Yukon Gear – Set Up Bearing (Part No.56036)

Yukon Gear – Replacement Standard Open Carrier Case For Dana 30, 3.73 & Up, Bare (Part No.20114)

Driveworks – Taper Bearing Cup (Part No.S-LM-501314)

Yukon Gear – Dana 30 Side Gear Thrust Washer (Part No.33284)

USA Standard Gear – Spartan Spring & Pin Kit, Fits Smaller Designs (Part No.17011)

Yukon Gear – Pinion Install Kit For Dana 30 Rear Differential (Part No.13017)

Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)

Popular 1973 Volvo 164 Differentials Categories

1973 Volvo 164 Differentials

Differentials Brands To Make Your 1973 Volvo 164 Last

Popular Valvoline Differentials

FAQs for 1973 Volvo 164 Differentials

What are the most purchased Differentials for the 1973 Volvo 164?

What are the top-rated 1973 Volvo 164 Differentials?

More Popular Parts for All Makes