from

$31.99

Product Features:

Pinion gear thrust washer
Fits Toyota Landcrusier

from

$603.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Toyota 9.5″ Landcruiser with 30 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$5.99

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landrcuiser (fine spline pinion) & T100/Tacoma with factory locker. 30mm socket, M20 x 1.5 thread.

Product Features:

Pinion nut for Suzuki Samurai, Toyota 8″, V6, Landcruiser with 30 spline pinion and Tacoma/T100 with factory locker
20mm x 1.5 thread
30mm socket

from

$436.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 1991 and up Toyota Landcruiser
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

from

$8.51

Axle Seal

from

$10.99

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

from

$8.99

Toyota Landcruiser ring gear nut for ring gear bolt.

Product Features:

Ring gear nut
Fits Toyota Landcruiser

from

$469.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Toyota 9.5″ Landcruiser
9.50″ ring gear diameter
27 spline pinion
10 ring gear bolts
4.88 ratio

from

$8.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$126.99

Bearing race driver front Toyota 7.5″, 8″, Landcruiser, and the Suzuki Samurai. No return. (TOY30306).

Product Features:

Bearing race driver
Fits 30306 race
All steel construction

from

$1099.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts.

Product Features:

Fits Toyota 9.5″ Landcruiser with 30 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$36.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Compatible with most oils and EP lubricants at higher operating temperatures
High resistance to oxidation and ozone and has low swell in hydrocarbon fluids
Temperature range: -20°F to 300°F; -29°C to 149°C
National® oil seals are recognized worldwide for their quality and reliable performance for every type of repair.

from

$103.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. No side shims.

Product Features:

Fits standard rotation Toyota Landcruiser
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$169.99

Yukon yoke for ’78 to ’84 Toyota Lancruiser with 27 spline pinion. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits 1978-1984 Toyota Landcruiser
27 spline

from

$192.99

Ring gear bolt kit for Toyota Landcruiser.

Product Features:

Fits standard rotation Toyota Landcruiser
Included are ring gear bolts and nuts

from

$274.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits standard rotation Toyota Landcruiser
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$34.99

Toyota Landcruiser crush sleeve. Approx 2.220″ long.

Product Features:

Crush sleeve
Fits Toyota Landcruiser
2.220″ tall

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications