from

$329.99

The B&M Sport Shifter features, Neutral safety switch, backup light switch, lighted gear indicator and black T-Handle and cable. Fits Most 3 and 4 Speed applications.

Product Features:

Base Trims For Custom Fit
Neutral Safety Switch
Backup Light Switch
Lighted Gear Indicator
Black T-Handle and Cable

from

$62.99

The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$78.99

Replace your stock black engine pulleys with a pair of chrome plated steel pulleys from Mr. Gasket. The pulleys are highly polished then chrome plated. Designed for small and big block Chevrolet engines with 5/8 inch water pump shaft.

Product Features:

Highly Polished For Lasting Beauty
Single Groove
w/Long Water Pump

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$21.99

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$7.99

Spectre’s Harmonic Balancer Bolt Kit is designed to fit Chevrolet Small Block 265-400 V8 engines. This grade 8 bolt is 2-1/2 inches long, and features a plated finish for corrosion resistance. This kit also includes a security lock washer.

Product Features:

Fits Chevrolet Small Block 265-400 V8 engines
Features a corrosion resistant plated finish
Gold iridite finish
Grade 8 bolt, 7/16 inch-20 by 2-1/2 inches
Includes security lock washer

from

$199.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1958-1986 Chevrolet Small Block 265-400 engines, this valve cover features polished aluminum construction and a ball milled design. Sold in pairs, this tall profile cover includes baffles to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1958-1986 Chevrolet Small Block 265-400 engines
Baffled for breather system compatibility
Sold in pairs
Polished aluminum construction
Tall profile
Features OEM style sealing edge
Holes in cover have an inside diameter of 1.220 inches

from

$379.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$58.99

Chrome water neck with a swivel top allows you to place your coolant hose where you want it to be, not just where the neck allows. Precision die cast for better fitment, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Chrome Plated Aluminum
O-ring To Prevent Leaks
Swivels For Hard To Fit Applications
Comes With Allen Head Bolts

from

$518.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$13.29

The special self locking timing cover bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5. Application: Chevy small and big block, 1/4 inch-20 ix 1/2 inch,10 pieces.

Product Features:

Ideal For Tight Spaces
Serrations Prevent Loosening
Flange Distributes Pressure
Zinc Plated Bolts
Grade 5 Material
Easy Installation

from

$42.49

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

42000 Volts
Effective To 6500 RPM
Quicker Starting
Improved Throttle Response
Higher RPM Power
Can Finished In Yellow

from

$62.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
Not for OEM Hydraulic Roller-Lifter Camshaft Eng.

from

$471.99

The unique design of these distributors fit tight intake systems while still transferring the high voltage of the MSD racing ignition to the spark plugs. The high voltage carrying capabilities are the result of several features which have been designed into these low-profile distributors. This includes a large diameter cap with wide spaced terminals and an injection molded Rynite rotor with thick vanes to stir up the air inside the cap. The high dielectric Rynite base also prevents arcing to the billet housing. Since these distributors are used primarily in racing applications, an oversized steel shaft is responsible for delivering the sparks. This shaft is QPQ coated for friction reduction and receives guidance from a sealed ball-bearing assembly and an extra long, precision sintered bushing for smooth operation. Note: must be used with an MSD crank trigger and ignition control.

Product Features:

Designed to fit low in the block to clear firewall/intake combos
Supplied w/Bronze Gear
Supplied w/Large Diameter HEI Style Distributor Cap And Rotor
Must Be Used w/An MSD Crank Trigger And MSD Ignition Control
O-ring seals can be installed for oil press. control (Mods only)
Special oil tract improves lubrication to the dist./cam gear
QPQ coated polished steel shaft; guided by sealed ball bearings
Oversized Polished Steel Shaft w/QPQ Coating

from

$65.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$17.49

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

Ideal For Tight Spaces
Serrations Prevent Loosening
Flange Distributes Pressure
Zinc Plated Bolts
Grade 5 Material
Easy Installation

from

$211.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:10 & DWN

from

$19.29

These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated. Similar in design to OEM units, these brackets can be adapted to other engines.

Product Features:

Chrome plated
Similar to OEM design
May be adaptable to other applications

from

$83.29

Billet aluminum handle with flexible braded steel tube mounts to the firewall. 29-3/4 inch long.

Product Features:

Braided Stainless Steel
Firewall Mounting
Includes Oil Fill Tube

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$363.99

These Mr. Gasket chrome alternators are remanufactured to exceed original equipment specifications for maximum dependability.

Product Features:

Fits Most 1966-’72 GM Vehicles
Bolt Spacing 6.6″
80 Amps
GM 10DN Style Alternator
Chrome Plated Finish
includes V-Belt Pulley – 1-Groove
Use w/ OEM Style Regulator

from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$1009.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
64cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$154.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers