from

$126.99

Product Features:

Carrier shim kit
Fits Dana Spicer 70 and 70HD

from

$194.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 60 differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Dana Spicer 60
Includes carrier bearings and races and carrier shim kit

from

$11.29

Product Features:

O-ring for seal housing
Fits Dana Spicer 60

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$36.99

Product Features:

Bulkhead fitting kit
Includes bulkhead fitting, outer fitting and o-ring

from

$89.99

Chrome replacement cover for Dana 60 and 61(not reverse rotation!).

Product Features:

Fits standard rotation Dana Spicer 60
Chrome

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$205.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:56 & UP

from

$266.99

Product Features:

GM10.5″ INTERNAL KIT (OPEN) 30 SPL

from

$892.99

Yukon replacement positraction internals for Dana 60 and 61 (full-floating) with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Dana Spicer 60 with Trac Loc positraction with 30 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$156.99

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

Cross pin shaft
Fits Dana Spicer 60 and 70
Powr Lok positraction only

from

$17.99

Manufactured with premium-grade steel, National® taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$16.99

Product Features:

Pinion depth shims for Dana Spicer 70 and 70HD, Ford 10.25″ and 10.5″

from

$14.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$323.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$3.99

Product Features:

Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″

from

$13.99

Product Features:

Cover gasket
Fits Dana Spicer 60, 70, 70U and 70HD

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$284.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 70
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$218.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$9.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$15.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

from

$5.99

Dana 60 pinion gear Thrust washer, standard Open & TracLoc (also 8.75″ Chrysler STD) Dana 70 2PC.

Product Features:

Pinion gear thrust washer for Dana Spicer 60
Fits standard open and Trac Loc applications

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$454.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Dana Spicer 70U
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers , thread locker, marking compound with brush, and gasket.