1973 GMC C15/C1500 Pickup Drivetrains
More 1973 GMC C15/C1500 Pickup Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1973 GMC C15/C1500 Pickup, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1973 GMC C15/C1500 Pickup Drivetrains
Yukon Gear – Standard Open Spider Gear Replacement Kit For Dana 60 And 61 With 35 Spline Axles (Part No.16085)
from
$301.99
Yukon standard open spider gear replacement kit for Dana 60 and 61 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Dana Spicer 60 open differential with 35 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
National – Bearings (Part No.HM89449)
from
$25.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – GM 12 Bolt Truck Cover Gasket (Part No.23015)
Yukon Gear – 1330 Dual-Size Cap U/Joint (Part No.42017)
from
$61.99
Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.
See More
Yukon Gear – Replacement Chrome Cover For Dana 44 (Part No.32004)
from
$67.99
0.080″ thick Chrome replacement cover for Dana 44.
Product Features:
See More
Product Features:
- Fits standard rotation Dana Spicer 44
- Chrome
Yukon Gear – Minor Install Kit For Dana 60 And 61 Differential (Part No.12026)
from
$151.99
Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 rear
- Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.
National – Shaft Repair Sleeve (Part No.99125)
from
$27.49
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Pro-King – Differential Internal Nest Kit (Part No.742J717)
from
$219.99
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – Bearing Race Driver (Part No.56006)
from
$215.99
Bearing race driver for Dana 44 rear. (TK 31520) No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits 31520 race
- All steel construction
Yukon Gear – C/Clip (Part No.33083)
from
$8.99
C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.
Product Features:
See More
Product Features:
- c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
- .150″ thick
Dorman – Spindle Nut 3/4 In.-20 Hex Size 1-1/16 In. (Part No.615-065.1)
from
$6.99
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Powertrax – No-Slip Traction System (Part No.9207822805)
from
$544.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles. Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction. Powertrax® = Extreme Traction Systems!
See More
National – Multi Purpose Seal (Part No.5200)
from
$12.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Powertrax – Grip LS Traction System (Part No.LS231230)
from
$480.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!
See More
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6053)
from
$39.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to CHEV 60-02; DODGE 64-66; FORD 75-15; GMC 60-02;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1960-2015
- Weight approx: 3 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.28 INCH / 58 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- NO STUDS
Motive Gear – Differential Gear Install Kit (Part No.GM12IK)
Yukon Gear – Replacement Yoke For Dana 30, 44, 50, And 300 With 26 Spline And A 1310 U/Joint Size (Part No.41018)
from
$121.99
Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 44
- 26 spline
- 1310 u-joint size
- 3.219″ snap ring span
- 1.062″ cap diameter
- Outside snap ring design
- U-bolt style
Yukon Gear – Set Up Bearing (Part No.56039)
from
$276.99
Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.
Product Features:
See More
Product Features:
- Set up bearing kit
- Fits Dana Spicer 60
- Easily slips on and off carrier journals to allow for easier carrier shim adjustment
Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)
from
$5.99
3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 60, 70 and 80
- 3/8″
Pro-King – Differential Pinion Shim Kit (Part No.742G200A)
from
$18.49
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – 1310, U/Jnt Straps & Bolts, 8.5" Front, 12P & 12T GM (Part No.41196)
from
$67.99
1310, U/Jnt straps & bolts, 8.5″ front, 12P & 12T GM.
Product Features:
See More
Product Features:
- u-joint strap kit
- Fits GM 12 bolt passenger car and truck and 8.5″ front
- 1310 u-joint size
- Includes two straps and four bolts
Yukon Gear – Pinion Install Kit For Dana 60 Rear Differential (Part No.13032)
from
$295.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 rear
- Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
Yukon Gear – 8.75" Chrysler & 55P Chevy Power Lok Clutches, Model 20 Also, Posi (Part No.16148)
from
$275.99
8.75″ Chrysler & 55P Chevy Power Lok clutches, Model 20 also, POSI.
Product Features:
See More
Product Features:
- Clutch kit
- Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Powr Lok positraction
Yukon Gear – Dana 60 Pinion Gear Thrust Washer, Standard Open & Tracloc (Also 8.75" Chrysler Std) Dana 70 2Pc (Part No.33287)
from
$5.99
Dana 60 pinion gear Thrust washer, standard Open & TracLoc (also 8.75″ Chrysler STD) Dana 70 2PC.
Product Features:
See More
Product Features:
- Pinion gear thrust washer for Dana Spicer 60
- Fits standard open and Trac Loc applications
USA Standard Gear – Steel Spool For Dana 44 With 30 Spline Axles, 3.73 & Down (Part No.59013)
from
$282.99
Product Features:
See More
- Fits Chrysler Dana Spicer 44 with 30 spline axles
- 3.73 and down ratio only
- Provides 100% traction to both wheels at all times
- Not recommended for street driven vehicles
National – Bearings (Part No.HM88610)
from
$15.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Replacement Cross Pin Shaft For Dana 60, Fits Standard Open And Trac Loc Posi (Part No.33314)
Yukon Gear – Dana 30 / 44 Roll Pin Replacement (Part No.33312)
from
$12.99
Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.
Product Features:
See More
Product Features:
- Roll pin for Dana Spicer 30 and Dana Spicer 44
- 0.235″ diameter
Popular 1973 GMC C15/C1500 Pickup Drivetrains Categories
1973 GMC C15/C1500 Pickup Drivetrains
You count on your 1973 GMC C15/C1500 Pickup to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 222 Drivetrains ranging in price from $0.91 to $1,674.99, you’re sure to find everything you need for your 1973 GMC C15/C1500 Pickup.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 18 different brands like Valvoline, Moog, and National. 1973 GMC C15/C1500 Pickup Drivetrains start as low as $0.91!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 9,482 extensive product reviews on 1973 GMC C15/C1500 Pickup Drivetrains. Some of the top-rated Drivetrains products we carry are Bearings with 4.2 stars and Greaseable Super Strength Universal Joint with 4.6 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1973 GMC C15/C1500 Pickup below to get started!
Top-Rated Drivetrains Brands For Your 1973 GMC C15/C1500 Pickup
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1973 GMC C15/C1500 Pickup running right for years to come. In our inventory you’ll find brands like Valvoline, Moog, National, and even more.
Popular Felpro Drivetrains
You’ll find popular Felpro brand products across Differentials. All are waiting to get your 1973 GMC C15/C1500 Pickup back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated Drivetrains
If are what you’re looking for, our inventory holds plenty. We stock brand Drivetrains for your 1973 GMC C15/C1500 Pickup, and some of our most reviewed parts include:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 1973 GMC C15/C1500 Pickup Drivetrains
What are the most purchased Drivetrains for the 1973 GMC C15/C1500 Pickup?
Out of 222 Drivetrains for the 1973 GMC C15/C1500 Pickup, the most popular in our inventory are:
What are the top-rated 1973 GMC C15/C1500 Pickup Drivetrains?
Top-rated Drivetrains for your 1973 GMC C15/C1500 Pickup based on customer reviews/ratings are:
from
$16.99
(39)
Bearings
“Perfect fit. Make sure you get your bearings completely filled with grease when reassembling your hubs.”
from
$32.99
(37)
Greaseable Super Strength Universal Joint
“grease fitting I like location dont like needle design to grease should be regular design fitting”
