from

$427.99

Product Features:

Satin Finish
4 Barrel
Annular Booster Type
Electric Choke Type
750 cfm Maximum Flow Rating

from

$38.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$104.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$12.09

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

Chrome Plated Steel
Set of 2 Caps
Easy Installation
2 Per Set

from

$95.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$105.99

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$48.49

Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:

Extra Thick Contact Arms
Large Radius Tungsten Contacts
High Strength Phenolic Rubbing Blocks
Prevents Points Float
Moisture-Proof Buna-N Condenser

from

$373.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$126.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$18.99

Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.

Product Features:

Allows Sway Bar System to Work At 100% Efficiency
Zerk Type Fittings
Allows for Periodic Greasing
Lasts Much Longer Than OEM Rubber Bushings
Handling Characteristics Improve Dramatically

from

$653.99

The street pro-billet distributors are the perfect choice for powerful engines that see plenty of street time. The street models share the same features as the small diameter models shown above, plus feature a vacuum advance. This canister provides improved economy and an accurate mechanical advance lets you dial-in an advance curve to match your driving needs. A magnetic pick-up produces accurate trigger signals that remain stable throughout the entire rpm range of your engine and is completely maintenance-free.

Product Features:

Billet housing 5/8 in. smaller dia. than stock Ford distributors
CARB E.O. Approved
Easy-to-adjust mech. advance w/supplied springs and stop bushings
Vacuum advance canister for improved economy (can be locked out)
CNC machined billet aluminum housing and billet aluminum base
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range
QPQ coated polished steel shaft; guided by sealed ball bearings
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction
Mech. advance assem. can be locked out for crank trigger systems
Advance weight pins are staked and tig welded to the plate

from

$26.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$27.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$577.99

RngPnn

from

$112.99

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

8.8mm Graphite Suppression
Silicone Spark Plug Boots
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

from

$19.99

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Chrome Plated
This Is A 45 Degree Neck
Comes With O-ring And Bolts
Has Small Hose Fitting On It

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$349.99

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer

from

$421.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$226.99

Product Features:

FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$158.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for Ford, Lincoln and Mercury (externally balanced) 289 and 302ci V8 engines with 28.2 ounce imbalance. Features include high tensile strength steel to resist elongation and cracking, 11.4 inch bolt pattern and 164 tooth ring gear. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M flexplates are ideal for hot rods, street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with C4 and C6 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$38.49

Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Thick parallel ground washer provides more accurate, uniform torque
Hex Prevents Socket Slippage
Accurate And Uniform Torque
Black Plated Finish

from

$154.99

The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

from

$42.49

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$15.99

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi

Product Features:

PerTronix D4062 Flame-Thrower HEI Distributor Rotor Blue
Made from hi-performance 60 KV rated alkyd molding compound.

from

$67.99

The B&M Shift Improver kit, is the easiest way to get the performance you want out of your transmission. A few simple modifications and your transmission will shift fast, firm and live longer.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features: