from

$329.99

Yukon positraction internals for 8.8″ Ford with 31 spline axles. This kit fits Yukon Gura Grip & Eaton positractions. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 8.8″ with Yukon Dura Grip positraction with 31 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$269.99

Plain Silver aluminum pinion Supprt for 9″ Ford Daytona, HD 6061.

Product Features:

Fits Ford 9″ with 28 spline pinion
Larger inner pinion bearing reduces gear deflection under high load
Races installed
6061 aluminum

from

$279.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses carrier bearings & races with an I.D. of 1.625″ and an O.D. of 2.891″. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Ford 9″ with LM501310 carrier race
Included are Timken bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$877.99

Yukon Extra HD 3.250″ nodular Iron dropout for Ford 9″ with load bolt. Yukon nodular iron dropouts feature a 5/8″ cap bolt and forged caps for maximum strength. Load bolt design prevents gear deflection under heavy loads. Rated up to 1400HP!

Product Features:

Fits Ford 9″
3.250″ carrier race diameter
Nodular iron for added strength
Load-bolt design reduces ring gear deflection under high horsepower

from

$51.99

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

Carrier race
Fits Ford 9″
Conversion race to install small bearing carrier into 3.250″ dropout

from

$4.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$8.99

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

Pinion gear thrust washer
Fits Ford 8.8″
0.750″ I.D.

from

$313.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Ford 9″
9.00″ ring gear diameter
28 spline pinion
10 ring gear bolts
6.50 ratio

from

$37.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$125.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$207.99

8.8″ Ford TracLoc (with long ears–for early models only) clutch set, both sides.

Product Features:

Clutch kit
Fit Ford 8.8″ Trac Loc positraction

from

$14.99

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion support o-ring
Fits Ford 9″

from

$434.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ with oversize Daytona pinion support
28 spline
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$6.99

Pinion support bolt for 8″ and 9″ Ford.

Product Features:

Pinion support bolt for Ford 8″ and 9″
3/8″ x 24 thread
1.0″ long

from

$5.79

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$1422.99

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$10.99

Crush Sleeve for Model 35, Chrysler 7.25″, 8.25″ Ford 8″ & GM 7.75″. Approx 0.495″ long.

Product Features:

Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
0.495″ tall

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$12.79

Product Features:

High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks
Long-life friction modifiers and premium base oils help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
Enhanced cleaning additives help reduce varnish formation and keep the transmission running properly longer
Engineered with a unique blend of viscosity modifiers and base oils to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$45.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$8.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$7.99

Product Features:

Housing stud
Fits Ford 8″ and 9″

from

$784.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″ with 31 spline axles
Trac Loc positraction
Clutch style positraction
Aggressive design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA