1973 Chevrolet Monte Carlo Performance Engines

Essential 1973 Chevrolet Monte Carlo Performance Engines

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.5885)

Ultra Seal: Oil Pan Gasket

from

$42.49
Manufactured from cellulose/nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile rubber composition gasket material
  • Provides excellent sealing and durability
  • Complete with molded rubber front/rear oil pan end seals where applicable
  • For OE replacement, high performance street, drag race and oval track use
  • Graphite Non-Wicking Rubber
  • No Cork Particles
  • Easy Removal For Disassembly
See More

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height

from

$126.99
Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:
  • Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
  • O.D.: 1.254″, I.D.: .880″
  • Single valve springs with damper
  • Approximately .490″ max lift at recommended installed height
See More

Edelbrock – Replacement Timing Cover Gasket #4243 For SB Chevy, Fits 2-Piece Part #4242 (Part No.4243)

Replacement Timing Cover Gasket #4243 For SB Chevy, Fits 2-Piece Part #4242

from

$41.99
Product Features:
  • Replacement Gasket Set For PN[4242]
See More

Edelbrock – Pushrod Set for S/B Chevy (Part No.9630)

Pushrod Set for S/B Chevy

from

$189.99


Product Features:
  • Case-Hardened Tubing
  • Welded Ends
  • 5/16 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Mr. Gasket – Precision Timing Tape (Part No.1591)

Precision Timing Tape

from

$16.49
Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:
  • 8″ diameter
  • 1970-73, 396-427-454 cu. in.
  • 1967-69, 302 cu. in.
  • 1965-68, 327 cu. in. hi-performance
  • 1970-76, 400 cu. in.
  • 1970-73, 350 cu. in.
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Rear Main Seal Gasket

from

$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Mr. Gasket – Water Neck (Part No.2557)

Water Neck

from

$27.49
Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:
  • Complete with o-rings and mounting bolts
  • Features an o-ring style seal to prevent water leaks
  • Chrome plated
  • 1/2″ NPT port can be used for various coolant temp related sensors or switches
See More

Competition Cams – CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA (Part No.12-601-8)

CAMSHAFT, SBC 291 MUTHA THUMPR HYDRAULIC ROLLER 1 EA

from

$522.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5867)

Ultra Seal: Valve Cover Gasket Set

from

$38.49
Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair, these gaskets are .187 inch thick. They fit both 1987-2002 Gen I Chevrolet Small Blocks as well as 1992-1997 Gen II LT-Based Small Blocks.

Product Features:
  • Manufactured from high-density cork /rubber blend gasket material
  • A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
  • Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
  • For OE replacement, high performance street, drag race and oval track
  • .187″ thick
  • Handles Ex Flange Pressure
  • Forms Leak Proof Seal
  • Black Latex Coating
See More

Mr. Gasket – Intake Gasket Set – Standard Duty – Big Block Chevy With Stock Rectangle Ports – 1.75"W X 2.50"H (Part No.108)

Intake Gasket Set - Standard Duty - Big Block Chevy With Stock Rectangle Ports - 1.75"W X 2.50"H

from

$29.99
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals & distributor gaskets if applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Competition Cams – MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST (Part No.1412-16)

MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST

from

$213.99
These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed

Product Features:
  • Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
  • For applications with less than 350 lbs. of open spring pressure
  • Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
  • Ultimate street roller rocker arm designed for serious performance enthusiasts
See More

Edelbrock – Performer Big-Block Chevy Oval Port Hydraulic Flat Tappet Springs (Part No.60489)

Performer Big-Block Chevy Oval Port Hydraulic Flat Tappet Springs

from

$830.99
Product Features:
  • Made of aluminum with a natural finish
  • 100cc chambers with 290cc intake ports
  • 2.19 in. intake and 1.88 in. exhaust valves
  • Bare Cylinder Head
  • Standard intake and exhaust port location
See More

Edelbrock – Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8 (Part No.5002)

Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8

from

$411.99
Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:
  • Designed for 2500 to 6500 Performance
  • Designed for Hi-Perf Street; Drag or Marine Use
  • Matched to Edelbrock Torker II Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Dyno Matched/Street Proven Performance
  • Take The Guesswork Out Of Camshaft Selection
See More

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

Intake Manifold Bolt Set - Chevrolet Small Block - Socket Head 3/8"-16 X 1" Bolts & Washers

from

$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:
  • Zinc plated to resist corrosion and provide a clean professional appearance
  • Made from Grade 5 steel for strength and durability
  • Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
  • Allen (socket) Head
  • Zinc Plated For Protection
See More

Mr. Gasket – Ultra Seal: Cylinder Head Bolts (Part No.941G)

Ultra Seal: Cylinder Head Bolts

from

$73.99
These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:
  • Cylinder Head Bolts
  • Longer-Than-Stock
  • High Quality Grade 8 Alloy
  • Increase Torque Settings
  • Higher Clamp Loads On Gasket
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Performer Series Retainer (Qty 16)

from

$95.99
Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:
  • Valve Spring Retainers for Use OE Cast Iron Heads
  • Superior Quality Heat-Treated Steel
  • Machined for Strength with Black Oxide Finish
  • Finish Ensures Rust and Corrosion Protection
See More

Weiand – Action Plus Water Pumps (Part No.9240P)

Action Plus Water Pumps

from

$215.99
Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:
  • Twisted Snout Water Pump Design For Updated Style
  • Street Performance
  • Heavy Duty Shaft w/5/8 in. Pilot
  • Six-Blade Stamped Steel
  • Anti-Cavitation Impeller
  • 100 Percent Leak Tested
See More

Holley – Strip Dominator; Intake Manifold (Part No.300-25)

Strip Dominator; Intake Manifold

from

$343.99
Strip Dominator intake manifold square bore carburetor mounting flange. Single plane with isolated plenum. Isolated water cross-over.

Product Features:
  • Single Plane With Isolated Plenum
  • Square Bore Carburetor Mounting Flange
  • Isolated Water Cross-Over
  • Power Band 4500-7600 rpm
  • Height Front 5.11 in. Rear 5.97 in.
  • Port Size 2.05 in. Height 1.22 in. Width
  • No Exhaust Heat Crossover Provision
  • Ideal For Drag Cars w/Auto Trans.
See More

B & M – Torque Converter, Holeshot 3000 (Part No.70421)

Torque Converter, Holeshot 3000

from

$789.99
The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

B & M – Torque Converter, Holeshot 2000 (Part No.70417)

Torque Converter, Holeshot 2000

from

$544.99
The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, new turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5801G)

Ultra Seal: Head Gasket

from

$64.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.190 inch, Compressed thickness 0.038 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1037)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$65.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Competition Cams – Thumpr 243/257 Hydraulic Flat Cam and Lifter Kit for Chevrolet Big Block 396-454 (Part No.CL11-602-4)

Thumpr 243/257 Hydraulic Flat Cam and Lifter Kit for Chevrolet Big Block 396-454

from

$1322.99
BIG BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.

Product Features:
  • Cam and lifter kit for Big Block Chevy engines
  • CL-Kit includes cam, lifters, assembly lube, instructions and decals
  • HYDRAULIC – Big Mutha’ Thumpr: Street/strip, needs 9.5:1 compression, 2800+ stall, intake, gears and headers, very rough idle.
  • 295/312 Advertised Duration, 243/257 Duration @ .050″, .522″/.507″ Lift, 107 Lobe Separation
  • Valve spring upgrade required
See More

Edelbrock – Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire (Part No.5487)

Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire

from

$367.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched To Performer Intake PN[5486]
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

Cylinder Head Dowel Pins

from

$17.79
Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Cylinder Head Dowel Pins

from

$14.99
Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

1973 Chevrolet Monte Carlo Performance Engines

Maybe you’re in the middle of a full rebuild of that 1973 Chevrolet Monte Carlo. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 130 different Performance Engines in our inventory ranging from $14.99 to $1,322.99. That means you can find the exact parts or products you need to keep that 1973 Chevrolet Monte Carlo running smoothly.

Performance Engines are only as good as their brand. We stock 8 different brands to make sure you have plenty of trusted parts to choose from for your 1973 Chevrolet Monte Carlo. Mr. Gasket, Edelbrock, and FEL-PRO Performance are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1973 Chevrolet Monte Carlo, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 512 reviews in this category, some of the top rated parts include Action Plus Water Pumps with 3.7 stars and Action Plus Water Pumps with 1.5 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1973 Chevrolet Monte Carlo rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1973 Chevrolet Monte Carlo Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1973 Chevrolet Monte Carlo demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Monte Carlo the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular B & M Performance Engines

We carry B & M parts in our stock across Performance Torque Converters categories, plus more. For a 1973 Chevrolet Monte Carlo, our most popular B & M Performance Engines include:
Tork Master 2400
from $339.99
(1)
Tork Master 2400
Performance Torque Converters
Tork Master 3000
from $499.99
(1)
Tork Master 3000
Performance Torque Converters

Top 1973 Chevrolet Monte Carlo Performance Engines from Mr. Gasket

Mr. Gasket products are another trusted brand when it comes to Performance Engines for your 1973 Chevrolet Monte Carlo. Popular Mr. Gasket parts include:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats

FAQs for 1973 Chevrolet Monte Carlo Performance Engines

What are the most purchased Performance Engines for the 1973 Chevrolet Monte Carlo?

Out of 130 Performance Engines for the 1973 Chevrolet Monte Carlo, the most popular in our inventory are:
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
from $195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
from $39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Lower Intake Manifold Gasket Set: 9 Piece Set
from $27.49
This product is not rated
Lower Intake Manifold Gasket Set: 9 Piece Set
Performance Engine Intake Manifold Gaskets

What are the top-rated 1973 Chevrolet Monte Carlo Performance Engines?

Top-rated Performance Engines for your 1973 Chevrolet Monte Carlo based on customer reviews/ratings are:
Action Plus Water Pumps
from $215.99
(3)
Action Plus Water Pumps
“I bought this item for my 1979 Camaro SBC for Street/Strip application. Water pump weighs 4 LBS less than factory, comes with its own cork gaskets. N”
Action Plus Water Pumps
from $215.99
(2)
Action Plus Water Pumps
“The twisted neck comes to far up on the hub. For a 2 groove pulley it causes the pulley to hit the water pump. You will also need new bolts for the”
Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet
from $334.99
(1)
Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet
“put this cam and lifter kit in my 412 inch small block chevy. works well with patriot alum. heads and edelbrock duel quad intake. all this is running ”