from

$396.99

Aluminum Girdle cover for 8.2″ and 8.5″ GM TA HD.

Product Features:

Fits GM 8.5″ and 8.6″
Aluminum girdle cover

from

$103.99

12P, 12T, CI VET, & 55GM 8460N REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits GM 12 bolt passenger car, 12 bolt truck and 1963-1979 Corvette

from

$8.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$618.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits GM 18.5″ with 30 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$376.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$425.99

Yukon positraction internals (0.806″ diameter) for GM 12P and 12T with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit GM 12 bolt passenger car and truck Dura Grip positraction with 30 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$518.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM88510 race
All steel construction

from

$2.49

Product Features:

RING GEAR BOLT 8.5″ 7.5″ 7/16 X 20 LEFT HAND

from

$47.99

Standard open cross pin (0.795″ diameter) for 8.5″ GM. fits some Eaton positractions.

Product Features:

Cross pin shaft for GM 8.5″ and 8.6″
Fits standard open differentials only
0.795″ diameter

from

$11.99

Standard Open pinion gear thrust washer for GM 12P and 12T.

Product Features:

Pinion gear thust washer for GM 12 bolt passenger car and truck
Fits standard open differentials only

from

$98.99

Product Features:

MINI SPOOL GM 10 BOLT 8 1/2″ 28 SPLINE

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$176.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits GM 8.5″ rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$21.99

Pinion nut washer for GM 12 bolt car & truck, 55-62 GM car & truck, GM 8.2″ & 63-79 Corvette.

Product Features:

Pinion nut washer for GM 12 bolt car and truck, 1955-1964 GM car and truck, GM 8.2″ and 1963-1979 Corvette.

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$52.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$336.99

Yukon positraction internals (0.795″ diameter) for 8.5″ GM with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. This kit is compatible with Yukon Dura Grip or Eaton positractions. It will not fit a factory Gov-Loc positraction.

Product Features:

Spider gear kit
Fits GM 8.5″ with 28 spline Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$404.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Carbon fiber clutches

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only

from

$519.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This is a thin gear designed for a 4.10 & up carrier.

Product Features:

Fits GM 12 bolt passenger car
8.875″ ring gear diameter
30 spline pinion
12 ring gear bolts
3.73 ratio
Thin gear set for 4.10 and up carrier

from

$139.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (with Supershims).

Product Features:

Fits GM 8.2″
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$386.99

GM 12P DURA GRIP case, bare, 4.10 & up, 30spline & 33spline.

Product Features:

Fits GM 12 bolt passenger car with 33 spline axles
Does not include spider gears

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$269.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features: